M74HCT245RM13TR ,OCTAL BUS TRANSCEIVER (3-STATE NON INVERTING)ABSOLUTE MAXIMUM RATINGS Symbol Parameter Value UnitV Supply Voltage-0.5 to +7 VCCV DC Input V ..
M74HCT245TTR ,OCTAL BUS TRANSCEIVER (3-STATE NON INVERTING)Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional o ..
M74HCT257B1R ,QUAD 2 CHANNEL MULTIPLEXER (3-STATE)Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional o ..
M74HCT257M1R ,QUAD 2 CHANNEL MULTIPLEXER (3-STATE)M74HCT257QUAD 2 CHANNEL MULTIPLEXER (3-STATE) ■ HIGH SPEED : t = 13 ns (TYP.) at V = 4.5VPD CC■ LO ..
M74HCT273 ,OCTAL D TYPE FLIP FLOP WITH CLEARM74HCT273OCTAL D TYPE FLIP FLOP WITH CLEAR ■ HIGH SPEED : ..
M74HCT273M1R ,OCTAL D TYPE FLIP FLOP WITH CLEARM74HCT273OCTAL D TYPE FLIP FLOP WITH CLEAR ■ HIGH SPEED : ..
MAX1510ETB+T ,Low-Voltage DDR Linear RegulatorsFeaturesThe MAX1510/MAX17510 DDR linear regulators source ● Internal Power MOSFETs with Current Lim ..
MAX1512ETA ,EEPROM-Programmable TFT VCOM CalibratorELECTRICAL CHARACTERISTICS(Circuit of Figure 1, V = 3V, V = 10V, V = 5V, R = 30.1kΩ , T = 0°C to +8 ..
MAX1512ETA+ ,EEPROM-Programmable TFT VCOM CalibratorELECTRICAL CHARACTERISTICS (continued)(Circuit of Figure 1, V = 3V, V = 10V, V = 5V, R = 30.1kΩ , T ..
MAX1512ETA+T ,EEPROM-Programmable TFT VCOM CalibratorFeaturesThe MAX1512 is a programmable VCOM-adjustment♦ 7-Bit Adjustable Sink-Current Outputsolution ..
MAX1513ETP ,2.7 to 5.5 V, TFT-LCD power-supply controllerFeatures♦ 2.7V to 5.5V Input Supply RangeThe MAX1513/MAX1514 provide complete power-sup-ply solutio ..
MAX1513ETP+ ,TFT-LCD Power-Supply ControllersFeatures♦ 2.7V to 5.5V Input Supply RangeThe MAX1513/MAX1514 provide complete power-sup-ply solutio ..
M74HCT245M1R-M74HCT245RM13TR-M74HCT245TTR
OCTAL BUS TRANSCEIVER (3-STATE NON INVERTING)
1/9August 2001 HIGH SPEED:
tPD = 13ns (TYP.) at VCC = 4.5V LOW POWER DISSIPATION:CC = 4μA(MAX.) at TA =25°C COMPATIBLE WITH TTL OUTPUTS : IH = 2V (MIN.) VIL = 0.8V (MAX) SYMMETRICAL OUTPUT IMPEDANCE:
|IOH| = IOL = 6mA (MIN) BALANCED PROPAGATION DELAYS:
tPLH ≅ tPHL PIN AND FUNCTION COMPATIBLE WITH
74 SERIES 245
DESCRIPTIONThe M74HCT245 is an advanced high-speed
CMOS OCTAL BUS TRANSCEIVER (3-STATE)
fabricated with silicon gate C2 MOS technology.
This IC is intended for two-way asynchronous
communication between data buses, and the
direction of data transmission is determined by
DIR input. The enable input G can be used to
disable the device so that the buses are effectively
isolated.
All inputs are equipped with protection circuits
against static discharge and transient excess
voltage.
All floating bus terminals during High Z State must
be held HIGH or LOW.
M74HCT245OCTAL BUS TRANSCEIVER
WITH 3 STATE OUTPUTS (NON INVERTED)
PIN CONNECTION AND IEC LOGIC SYMBOLS
ORDER CODES
M74HCT2452/9
INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION
TRUTH TABLE X : Don’t Care
Z : High Impedance
ABSOLUTE MAXIMUM RATINGS Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is
not implied
(*) 500mW at 65 °C; derate to 300mW by 10mW/°C from 65°C to 85°C
RECOMMENDED OPERATING CONDITIONS
M74HCT2453/9
DC SPECIFICATIONS
AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6ns)
M74HCT2454/9
CAPACITIVE CHARACTERISTICS 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without
load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/8 (per circuit)
TEST CIRCUIT CL = 50pF/150pF or equivalent (includes jig and probe capacitance)
R1 = 1KΩ or equivalent
RT = ZOUT of pulse generator (typically 50Ω)
M74HCT2455/9
WAVEFORM 1 : PROPAGATION DELAY TIME (f=1MHz; 50% duty cycle)
WAVEFORM 2 : OUTPUT ENABLE AND DISABLE TIME (f=1MHz; 50% duty cycle)
