M74HC74M1R ,DUAL D TYPE FLIP FLOP WITH PRESET AND CLEARM74HC74DUAL D TYPE FLIP FLOP WITH PRESET AND CLEAR ■ HIGH SPEED : ..
M74HC74RM13TR ,DUAL D TYPE FLIP FLOP WITH PRESET AND CLEARlogic diagram has not be used to estimate propagation delays2/12M74HC74
M74HC74TTR ,DUAL D TYPE FLIP FLOP WITH PRESET AND CLEARM74HC74DUAL D TYPE FLIP FLOP WITH PRESET AND CLEAR ■ HIGH SPEED : ..
M74HC75M1R ,4 BIT D TYPE LATCHM74HC754 BIT D TYPE LATCH ■ HIGH SPEED : t = 11ns ( ..
M74HC85M1R ,4-BIT MAGNITUDE COMPARATORAbsolute Maximum Ratings are those values beyond which damage to the device may occur. Functional o ..
M74HC85M1R ,4-BIT MAGNITUDE COMPARATORM74HC854-BIT MAGNITUDE COMPARATOR ■ HIGH SPEED : t ..
MAX15005BAUE+ ,4.5V to 40V Input Automotive Flyback/Boost/SEPIC Power-Supply ControllersFeaturesThe MAX15004A/B/MAX15005A/B high-performance, ● Wide Supply Voltage Range Meets Automotive ..
MAX15006AASA+T ,40V, Ultra-Low Quiescent-Current Linear Regulators in 6-Pin TDFN/8-Pin SOElectrical Characteristics(V = 14V, I = 1mA, C = 0.1μF, C = 2.2μF, T = T = -40°C to +125°C, unless ..
MAX15006AATT+ ,40V, Ultra-Low Quiescent-Current Linear Regulators in 6-Pin TDFN/8-Pin SOFeatures● Wide Operating Input Voltage Range (4V to 40V)The MAX15006/MAX15007 ultra-low quiescent-c ..
MAX15006BASA+T ,40V, Ultra-Low Quiescent-Current Linear Regulators in 6-Pin TDFN/8-Pin SOApplicationsPART TEMP RANGEPACKAGE MARK● AutomotiveMAX15006AASA+ -40°C to +125°C 8 SO-EP* —● Tire-P ..
MAX15006BATT+ ,40V, Ultra-Low Quiescent-Current Linear Regulators in 6-Pin TDFN/8-Pin SOElectrical Characteristics(V = 14V, I = 1mA, C = 0.1μF, C = 2.2μF, T = T = -40°C to +125°C, unless ..
MAX15007AASA+ ,40V, Ultra-Low Quiescent-Current Linear Regulators in 6-Pin TDFN/8-Pin SOFeatures● Wide Operating Input Voltage Range (4V to 40V)The MAX15006/MAX15007 ultra-low quiescent-c ..
M74HC74B1R-M74HC74M1R-M74HC74RM13TR-M74HC74TTR
DUAL D TYPE FLIP FLOP WITH PRESET AND CLEAR
1/12July 2001 HIGH SPEED :
fMAX = 67MHz (TYP.) at VCC = 6V LOW POWER DISSIPATION:CC =2μA(MAX.) at TA =25°C HIGH NOISE IMMUNITY:NIH = VNIL = 28 % VCC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE:
|IOH| = IOL = 4mA (MIN) BALANCED PROPAGATION DELAYS:
tPLH ≅ tPHL WIDE OPERATING VOLTAGE RANGE:CC (OPR) = 2V to 6V PIN AND FUNCTION COMPATIBLE WITH
74 SERIES 74
DESCRIPTIONThe M74HC74 is an high speed CMOS DUAL D
TYPE FLIP FLOP WITH CLEAR fabricated with
silicon gate C2 MOS technology.
A signal on the D INPUT is transferred on the Q
OUTPUT during the positive going transition of the
clock pulse. CLEAR and PRESET are
independent of the clock and accomplished by a
low on the appropriate input.
All inputs are equipped with protection circuits
against static discharge and transient excess
voltage.
M74HC74DUAL D TYPE FLIP FLOP WITH PRESET AND CLEAR
PIN CONNECTION AND IEC LOGIC SYMBOLS
ORDER CODES
M74HC742/12
INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION
TRUTH TABLE X : Don’t Care
LOGIC DIAGRAM This logic diagram has not be used to estimate propagation delays
M74HC743/12
ABSOLUTE MAXIMUM RATINGS Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is
not implied
(*) 500mW at 65 °C; derate to 300mW by 10mW/°C from 65°C to 85°C
RECOMMENDED OPERATING CONDITIONS
M74HC744/12
DC SPECIFICATIONS
M74HC745/12
AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6ns)
CAPACITIVE CHARACTERISTICS 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without
load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/2 (per FLIP/
FLOP)
M74HC746/12
TEST CIRCUIT CL = 50pF or equivalent (includes jig and probe capacitance)
RT = ZOUT of pulse generator (typically 50Ω)
WAVEFORM 1: nCK TO nQ,nQ PROPAGATION DELAY TIMES,nD TO nCK SETUP AND HOLD
TIMES, nCK MINIMUM PULSE WIDTH, MAXIMUM nCK FREQUENCY (f=1MHz; 50% duty cycle)
