M74HC4515B1R ,4 TO 16 LINE DECODER/LATCHM74HC4515 4 TO 16 LINE DECODER/LATCH (INV.) ■ HIGH SPEED:t = 20 ns (TYP.) at V = 6VPD CC■ LOW POWE ..
M74HC4520M1R ,DUAL 4 BIT BINARY COUNTERM74HC4520DUAL 4 BIT BINARY COUNTER ■ HIGH SPEED : f ..
M74HC4538 ,DUAL RETRIGGERABLE MONOSTABLE MULTIVIBRATORFUNCTIONAL DESCRIPTION operating. That means that after triggering whenthe voltage R/C external ret ..
M74HC4538B1R ,DUAL RETRIGGERABLE MONOSTABLE MULTIVIBRATORlogic diagram has not be used to estimate propagation delays2/11M74HC4538TIMING CHART
M74HC4538M1R ,DUAL RETRIGGERABLE MONOSTABLE MULTIVIBRATORBLOCK DIAGRAM (1) Cx, Rx, Dx are external components.(2) Dx is a clamping diode.The external capa ..
M74HC4538M1R ,DUAL RETRIGGERABLE MONOSTABLE MULTIVIBRATORFUNCTIONAL DESCRIPTION operating. That means that after triggering whenthe voltage R/C external ret ..
MAX1486CUB ,Software-Selectable / Half-/Full-Duplex / Slew-Rate-Limited / 12Mbps / RS-485/RS-422 Transceivers in MAX PackageELECTRICAL CHARACTERISTICS(V = +5V ±5%, T = T to T , unless otherwise noted. Typical values are at ..
MAX1486CUB+T ,Software-Selectable, Half-/Full-Duplex, Slew-Rate-Limited,12Mbps, RS-485/RS-422 Transceivers in µMAX PackageApplications0.1μA. All devices operate from a single 5V supply.Low-Power RS-422/RS-485 Communicatio ..
MAX1486EUB ,Software-Selectable / Half-/Full-Duplex / Slew-Rate-Limited / 12Mbps / RS-485/RS-422 Transceivers in MAX PackageFeaturesThe MAX1481/MAX1484/MAX1485/MAX1486 provide' 10-Pin µMAX Package: Smallest 10-Pin Packageso ..
MAX1486EUB ,Software-Selectable / Half-/Full-Duplex / Slew-Rate-Limited / 12Mbps / RS-485/RS-422 Transceivers in MAX PackageApplications0.1µA. All devices operate from a single 5V supply.Low-Power RS-422/RS-485 Communicatio ..
MAX1486EUB+ ,Software-Selectable, Half-/Full-Duplex, Slew-Rate-Limited,12Mbps, RS-485/RS-422 Transceivers in µMAX PackageGeneral Description ________
MAX1486EUB+ ,Software-Selectable, Half-/Full-Duplex, Slew-Rate-Limited,12Mbps, RS-485/RS-422 Transceivers in µMAX PackageFeaturesThe MAX1481/MAX1484/MAX1485/MAX1486 provide♦ 10-Pin µMAX Package: Smallest 10-Pin Packageso ..
M74HC4515B1R
4 TO 16 LINE DECODER/LATCH
1/10August 2001 HIGH SPEED:
tPD= 20 ns (TYP.) at VCC = 6V LOW POWER DISSIPATION:CC = 4μA(MAX.) at TA =25°C HIGH NOISE IMMUNITY:NIH = VNIL = 28 % VCC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE:
|IOH| = IOL = 4mA (MIN) BALANCED PROPAGATION DELAYS:
tPLH ≅ tPHL WIDE OPERATING VOLTAGE RANGE:CC (OPR) = 2V to 6V PIN AND FUNCTION COMPATIBLE WITH
74 SERIES 4515
DESCRIPTIONThe M74HC4515 is an high speed CMOS 4 LINE
TO 16 LINE SEGMENT DECODER WITH
LATCHED INPUTS fabricated with silicon gate2 MOS technology.
A binary code stored in the four input latches (A to
D) provides a low level at the selected one of
sixteen outputs excluding the other fifteen outputs,
when the inhibit input (INHIBIT) is held low. When
the inhibit input(INHIBIT) is held high, all outputs
are kept high level, while the latch function is
available. The data applied to the data inputs are
transferred to the Q outputs of latches when the
strobe input is held high. When the strobe input is
taken low, the information data applied to the data
input at a time is retained at the output of the
latches.
All inputs are equipped with protection circuits
against static discharge and transient excess
voltage.
M74HC4515 4 TO 16 LINE DECODER/LATCH (INV.)
PIN CONNECTION AND IEC LOGIC SYMBOLS
ORDER CODES
M74HC45152/10
INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION
TRUTH TABLE X : Don’t Care
M74HC45153/10
LOGIC DIAGRAM This logic diagram has not be used to estimate propagation delays
ABSOLUTE MAXIMUM RATINGS Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is
not implied
(*) 500mW at 65 °C; derate to 300mW by 10mW/°C from 65°C to 85°C
M74HC45154/10
RECOMMENDED OPERATING CONDITIONS
DC SPECIFICATIONS
M74HC45155/10
AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6ns)
CAPACITIVE CHARACTERISTICS 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without
load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC
M74HC45156/10
TEST CIRCUIT CL = 50pF or equivalent (includes jig and probe capacitance)
RT = ZOUT of pulse generator (typically 50Ω)
SWITCHING CHARACTERISTICS TEST WAVEFORM (f=1MHz; 50% duty cycle)
