M74HC125RM13TR ,QUAD BUS BUFFERS (3-STATE)Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional o ..
M74HC126M1R ,QUAD BUS BUFFER (3-STATE)Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional o ..
M74HC126RM13TR ,QUAD BUS BUFFER (3-STATE)M74HC126QUAD BUS BUFFER (3-STATE) ■ HIGH SPEED: t = 8ns (TYP.) at V = 6VPD CC■ LOW POWER DISSIPAT ..
M74HC126TTR ,QUAD BUS BUFFER (3-STATE)ABSOLUTE MAXIMUM RATINGS Symbol Parameter Value UnitV Supply Voltage-0.5 to +7 VCCV DC Input V ..
M74HC132B1R ,QUAD 2-INPUT SCHMITT NAND GATEAbsolute Maximum Ratings are those values beyond which damage to the device may occur. Functional o ..
M74HC132M1R ,QUAD 2-INPUT SCHMITT NAND GATEM74HC132QUAD 2-INPUT SCHMITT NAND GATE ■ HIGH SPEED:t = 11ns (TYP.) at V = 6VPD CC■ LOW POWER DISS ..
MAX13082ECSA ,+5.0V, ±15kV ESD-Protected, Fail-Safe, Hot-Swap, RS-485/RS-422 Transceiversfeatures independentlyprogrammable receiver and transmitter output phasePART TEMP RANGE PIN-PACKAGE ..
MAX13082ECSA+ ,+5.0V, ±15kV ESD-Protected, Fail-Safe, Hot-Swap, RS-485/RS-422 TransceiversFeaturesThe MAX13080E–MAX13089E +5.0V, ±15kV ESD-protect-♦ +5.0V Operationed, RS-485/RS-422 transce ..
MAX13082EESA+ ,+5.0V, ±15kV ESD-Protected, Fail-Safe, Hot-Swap, RS-485/RS-422 TransceiversFeaturesThe MAX13080E–MAX13089E +5.0V, ±15kV ESD-protect-♦ +5.0V Operationed, RS-485/RS-422 transce ..
MAX13082EESA+T ,+5.0V, ±15kV ESD-Protected, Fail-Safe, Hot-Swap, RS-485/RS-422 Transceiversfeatureslew-rate-limited drivers but allow transmit speeds up to♦ Pin-Selectable Full-/Half-Duplex ..
MAX13084EASA ,+5.0V, ±15kV ESD-Protected, Fail-Safe, Hot-Swap, RS-485/RS-422 TransceiversFeaturesThe MAX13080E–MAX13089E +5.0V, ±15kV ESD-protect-♦ +5.0V Operationed, RS-485/RS-422 transce ..
MAX13084ECPA ,+5.0V, ±15kV ESD-Protected, Fail-Safe, Hot-Swap, RS-485/RS-422 Transceiversfeatures independentlyprogrammable receiver and transmitter output phasePART TEMP RANGE PIN-PACKAGE ..
M74HC125B1R-M74HC125M1R-M74HC125RM13TR
QUAD BUS BUFFERS (3-STATE)
1/10August 2001 HIGH SPEED:
tPD = 8ns (TYP .) at VCC = 6V LOW POWER DISSIPATION:CC = 4μA(MAX.) at TA =25°C HIGH NOISE IMMUNITY:NIH = VNIL = 28 % VCC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE:
|IOH| = IOL = 6mA (MIN) BALANCED PROPAGATION DELAYS:
tPLH ≅ tPHL WIDE OPERATING VOLTAGE RANGE:CC (OPR) = 2V to 6V PIN AND FUNCTION COMPATIBLE WITH
74 SERIES 125
DESCRIPTIONThe M74HC125 is an high speed CMOS QUAD
BUFFER (3-STATE) fabricated with silicon gate2 MOS technology.
The device requires the 3-STATE control input G
to be set high to place the output into the high
impedance state.
All inputs are equipped with protection circuits
against static discharge and transient excess
voltage.
M74HC125QUAD BUS BUFFER (3-STATE)
PIN CONNECTION AND IEC LOGIC SYMBOLS
ORDER CODES
M74HC1252/10
INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION
TRUTH TABLE
ABSOLUTE MAXIMUM RATINGS Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is
not implied
(*) 500mW at 65 °C; derate to 300mW by 10mW/°C from 65°C to 85°C
RECOMMENDED OPERATING CONDITIONS
M74HC1253/10
DC SPECIFICATIONS
M74HC1254/10
AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 6ns)
CAPACITIVE CHARACTERISTICS 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without
load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/4 (per buffer)
M74HC1255/10
TEST CIRCUIT CL = 50pF/150pF or equivalent (includes jig and probe capacitance)
R1 = 1KΩ or equivalent
RT = ZOUT of pulse generator (typically 50Ω))
WAVEFORM 1 : PROPAGATION DELAY TIMES (f=1MHz; 50% duty cycle)
M74HC1256/10
WAVEFORM 2 : OUTPUT ENABLE AND DISABLE TIMES (f=1MHz; 50% duty cycle)
