M22100-B1 ,4 X 4 CROSSPOINT SWITCH WITH CONTROL MEMORYAbsolute Maximum Ratings are those values beyond which damage to the device may occur. Functional o ..
M22101B1 ,WITH CONTROL MEMORY 4 X 4 X 2 CROSSPOINT SWITCHESM22101M221024 X 4 X 2 CROSSPOINT SWITCHESWITH CONTROL MEMORY. LOW ON RESISTANCE – 75 Ω TYP AT There ..
M22102B1 ,WITH CONTROL MEMORY 4 X 4 X 2 CROSSPOINT SWITCHESAbsolute Maximum Ratings” may cause permanent damage to thedevice. This isa stress ratingonly and f ..
M2-352 ,TECHNIK - HIGH RELIABILITY FOR LOW COST
M24128 ,256/128 KBIT SERIAL I2C BUS EEPROM WITHOUT CHIP ENABLE LINESLogic DiagramThe M24256B, M24128B and M24256A are alsoavailable, and offer the extra functionality ..
M24128BFMB6TG ,128 Kbit Serial I2C Bus EEPROMAbsolute maximum ratings . 22Table 6. Operating conditions (voltage range W) . . . . . . ..
M37902FJCHP , SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37903S4CHP , 16-BIT CMOS MICROCOMPUTER
M37905F8CFP , 16-BIT CMOS MICROCOMPUTER
M37905F8CFP , 16-BIT CMOS MICROCOMPUTER
M37906F8CSP , 16-BIT CMOS MICROCOMPUTER
M37920FGCGP , SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION
M22100B1-M22100-B1
4 X 4 CROSSPOINT SWITCH WITH CONTROL MEMORY
1/10February 2003 LOW ON RESISTANCE - 75Ω Typ.
at VDD = 12v "BUILT IN" CONTROL LATCHES LARGE ANALOG SIGNAL
CAPABILITY ± VDD/2 TRANSMITS SIGNALS UP TO 10 MHz MATCHED SWITCH CHARACTERISTICS RON = 18Ω Typ. at VDD-VSS = 12V HIGH LINEARITY : - 0.5% DISTORTION Typ.
at f = 1KHz, VIN = 5 VppVDD - VSS = 10V, RL = 10KΩ STANDARD COS/MOS NOISE IMMUNITY 100% TESTED FOR QUIESCENT CURRENT
DESCRIPTIONThe M22100 combines a 4 x 4 array of crosspoints
(transmission gates) with a 4 line to 16 line
decoder and 16 latch circuits. Any one of the
sixteen transmission gates (crosspoints) can be
selected by applying the appropriate four line
address. The selected transmission gate can be
turned on or off by applying a logical one or zero,
respectively, to the data input and strobing the
strobe input to a logical one. Any number of the
transmission gates can be ON simultaneously.
When the required operating power is applied to
the 22100, the states of the 16 switches are
indeterminate.
Therefore, all switches must be turned off by
putting the strobe high and data in low, and the
addressing all switches in succession.
M221004x4 CROSSPOINT SWITCH WITH CONTROL MEMORY
PIN CONNECTION
ORDER CODES
M22100B2/10
IINPUT EQUIVALENT CIRCUIT PIN DESCRIPTION
FUNCTIONAL DIAGRAM
TRUTH TABLE
M22100B3/10
LOGIC DIAGRAM
ABSOLUTE MAXIMUM RATINGS Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is
not implied.
All voltage values are referred to VSS pin voltage.
RECOMMENDED OPERATING CONDITIONS
M22100B4/10
DC SPECIFICATIONS The Noise Margin for both "1" and "0" level is: 1V min. with VDD=5V, 2V min. with VDD=10V, 2.5V min. with VDD=15V
* : Determined by minimum feasible leakage measurement for automating testing
M22100B5/10
DYNAMIC ELECTRICAL CHARACTERISTICS (T amb = 25°C, CL = 50pF, RL = 200KΩ, tr = tf = 20 ns)
M22100B6/10
(*) Typical temperature coefficient for all VDD value is 0.3 %/°C.
(1) Peak to Peak voltage symmetrical about VDD/2
WAVEFORM 1 : PROPAGATION DELAY TIMES (f=1MHz; 50% duty cycle)
