LM311DT ,VOLTAGE COMPARATORSABSOLUTE MAXIMUM RATINGS Symbol Parameter Value UnitV Supply Voltage 36 VCCV Differential In ..
LM311H ,Voltage ComparatorMaximum Ratings for the LM111-N/LM211-NTotal Supply Voltage (V ) 36V84Output to Negative Supply Vol ..
LM311H. ,Voltage ComparatorApplications (Note 3) (Continued)Digital Transmission Isolator Relay Driver with Strobe005704400057 ..
LM311J ,Voltage ComparatorApplications (Note 3)Offset Balancing StrobingDS005704-36DS005704-37Note: Do Not Ground Strobe Pin. ..
LM311J ,Voltage ComparatorGeneral Descriptiontions. The LM111 has the same pin configuration as theThe LM111, LM211 and LM311 ..
LM311J ,Voltage ComparatorLM111/LM211/LM311 Voltage ComparatorJanuary 2001LM111/LM211/LM311Voltage Comparatorthe devices are ..
LMBD3004SLT1G , HIGH VOLTAGE SURFACE MOUNT SWITCHING DIODE
LMBD6100LT1G , Monolithic Dual Switching Diode
LMBD7000LT1 , Dual Switching Diode
LMBD914LT1G , High-Speed Switching DIODE
LMBR0520T1G , Surface Mount Schottky Power Rectifier Pb-Free package is available
LMBR130T1G , Surface Mount Schottky Power Rectifier Pb-Free package is available
LM111D-LM211DT-LM211N-LM311DT
VOLTAGE COMPARATORS
MAXIMUM INPUT CURRENT : 150nA MAXIMUM OFFSET CURRENT : 20nA DIFFERENTIAL INPUT VOLTAGE RANGE : ±30V POWER CONSUMPTION :135mW AT ±15V SUPPLY VOLTAGE : +5V TO ±15V OUTPUT CURRENT : 50mA
DESCRIPTIONThe LM111, LM211, LM311 are voltage compara-
tors that have low input currents.
They are also designed to operate over a wide
range of supply voltages : from standard ±15V op-
erational amplifier supplies down to the single +5V
supply used for IC logic.
Their output is compatible with RTL-DTL and TTL
as well as MOS circuits and can switch voltages
up to +50V at outputs currents as high as 50mA.
ORDER CODE
N = Dual in Line Package (DIP)
D = Small Outline Package (SO) - also available in Tape & Reel (DT)
PIN CONNECTIONS (top view)
LM111
LM211 - LM311VOLTAGE COMPARATORS
LM111-LM211-LM311
SCHEMATIC DIAGRAM
ABSOLUTE MAXIMUM RATINGS
OPERATING CONDITIONS This rating applies for ±15V supplies. The positive input voltage limit is 30V above the negative. The negative input voltage is equal to the
negative supply voltage or 30V below the positive supply, whichever is less. Pd is calculated with Tamb = +25°C, Tj = +150°C and Rthja = 100°C/W for DIP8 package= 175°C/W for SO8 package
LM111-LM211-LM311
ELECTRICAL CHARACTERISTICSVCC+ = ±15V, Tamb = +25°C (unless otherwise specified) The offset voltage, offset current and bias current specifications apply for any supply voltage from a single +5V suplly up to ±15V
supplies The offset voltages and offset currents given are the maximum values required to drive the output down to +1V or up to +14V with a1mA load current. Thus, these parameters define an error band and take into account the worst-case of voltage gain and input impedance. The response time specified (see definitions) is for a 100mV input step with 5mV overdrive.
LM111-LM211-LM311
LM111-LM211-LM311
LM111-LM211-LM311
