L6287 ,POWER COMBO DRIVERL6287POWER COMBO DRIVERDESCRIPTIONThe F-VHS Motor Driver COMBO IC includes adouble three phase brus ..
L6287 ,POWER COMBO DRIVERELECTRICAL CHARACTERISTICS (Tj = 0 to125 C; VCC = VS = 5V 5%; VDC = VDL = V = 10 to 18V;unless othe ..
L6301 , The best light source is supported by the best electrode technology
L6301 , The best light source is supported by the best electrode technology
L6301 , The best light source is supported by the best electrode technology
L6370D ,2.5A HIGH-SIDE DRIVER INDUSTRIAL INTELLIGENT POWER SWITCHELECTRICAL CHARACTERISTICS (V = 24V; T = –25 to +125°C, unless otherwise specified)S JSymbol Param ..
LC3517AML-15 ,150ns, 2048-word x 8-bit CMOS static RAM (SRAM)FEATURES. 100 ns (11:3517A-10 series), 120 ns (UB5WA.12 series) and 150 ns (LC3517A-15 series) maxi ..
LC3517AS-15 ,150ns, 2048-word x 8-bit CMOS static RAM (SRAM)BLOCK DIAGRAM+2riir;PIN DESCRIPTION".LLCiiiinECTCiFCT' num» _n“_n“—“——nn—IICiLLCTCEtiCT,SPECI FICAT ..
LC3517ASL-10 ,100ns, 2048-word x 8-bit CMOS static RAM (SRAM)FEATURES. 100 ns (11:3517A-10 series), 120 ns (UB5WA.12 series) and 150 ns (LC3517A-15 series) maxi ..
LC3517ASL-12 ,120ns, 2048-word x 8-bit CMOS static RAM (SRAM)BLOCK DIAGRAM+2riir;PIN DESCRIPTION".LLCiiiinECTCiFCT' num» _n“_n“—“——nn—IICiLLCTCEtiCT,SPECI FICAT ..
LC35256A-10 ,256 K (32768 words x 8 bit) SRAM with OE and CE pinsOrdering number: EN4916ANo. 4916AOverviewThe LC35256A, AS, AM, and AT are 32768 words K8-bits async ..
LC35256AM-10 ,256 K (32768 words x 8 bit) SRAM with OE and CE pinsFeatures. Supply voltage range: 2.7 to 5.5 V5 V operation: 5.0 V :10%3 V operation: 2.7 to 3.6 V. A ..
L6287
POWER COMBO DRIVER
L6287POWER COMBO DRIVER
DESCRIPTIONThe F-VHS Motor Driver COMBO IC includes a
double three phase brushless motor driver plus a
DC full bridge motor driver for VCR application.
The package is SDIP42 (38+2+2 pin ground
frame).
The device is realized in BCD technology with
power LDMOS output stages.
The gate drive for high side stages is provided by
an internal charge pump with two external capaci-
tors. The first three phase motor driver is devoted
to the DRUM motor control.
The phase sequence update signal is provided in-
itially by an external start-up signal (FSTART),
whose frequency is internally divided by four,
while, during normal operation, is provided by an
optical tacho converter signal.
This signal is used as clock and reset for the state
machine.
The regulation of the speed is externally provided
by means of PWM signal generated by the μP
(DPWM), without external sensing resistor. The
feedback to the μP unit is given by a suitable
open drain output signal (PUD) synchronized by
the internal state machine.
The second three phase motor driver is devoted
to the CAPSTAN control. While the DRUM will al-
ways spin in a fixed direction, the CAPSTAN mo-
tor needs a more sophisticated logic to control the
changes in spin direction.
The motor position detection is carried out by
means of three comparators for Hall effect sen-
sors. The loop regulation for this motor is still pro-
vided by the μP with the signals CPWM and
CDIR.
The LOADING motor section include a full bridge
DC motor driver. The motor operations are di-
rectly set by the inputs LPWM, LDIR according to
the truth table reported on the page 5.
The device also includes a circuit for early ther-
mal alarm, last thermal alarm and thermal shut-
down with hysteresys. The output of this stage is
an open drain, kept ON during normal operations.
The THERM signal follows the inverted FSTART
signal between early warning and last warning
temperature, while remains in high impedance
(OFF) after lastwarning temperature and during
thermal shutdown.
The STANDBY state of the device is imposed by
THERMAL SHUTDOWN
UNDERVOLTAGE ON VCC SUPPLY
EXTERNAL SIGNAL FSTART;
This state is imposed automatically after a de-
fined time-out.
The time-out is realized by sensing the falling
edges of the FSTART signal: if no edges are re-
corded for a time interval greater than a certain
time constant, the STANDBY condition is gener-
ated.
The time constant is defined by the external ca-
pacitor CTO.
In the STANDBY state the main functions (upper
power stages, opto decoder, etc) of the device
are turned off in order to minimize the power con-
sumption.
The device also implement a HEATER function.
The HEATER transistor is OFF during thermal
shutdown, undervoltage condition and during nor-
mal working mode.
The HEATER transistor is driven ON when the
external STANDBY condition is present according
to the following table:
During the ON condition, the specified heater Ron
is not guaranteed if all the voltage supplies are
not at their minimum nominal value.
ABSOLUTE MAXIMUM RATINGS(**) Not operative - STANDBY condition
(***) Each motor driver
PINS CONNECTION
THERMAL DATANote: Batwing pin.
L62872/9
BLOCK DIAGRAM
L6287
PIN DESCRIPTION
L62874/9
ELECTRICAL CHARACTERISTICS (Tj = 0 to125°C; VCC = VS = 5V ±5%; VDC = VDL = VDD = 10 to 18V;unless otherwise specified.)
POWER SUPPLY
# WARNINGThe functionality of the I.C. is guaranted in this voltage range. Nevertheless the specified operating voltages (VDC, VDD, VDL), must be selected
according to the load characteristics. Proper cautions must be taken in the application in order to assure that the drain-source voltage across
each output power transistor does not exceed 20V max.
LOADING MOTOR
DRUM MOTOR
CAPSTAN MOTOR
(*) WARNINGThese current values are compatible with the structure of the IC power structure. Nevertheless the use of these current levels could produce
junction temperatures that force IC outside of the operative range due to the thermal characteristics of the choosen package.
L6287
