L6285 ,3 CHANNELS MULTIPOWER SYSTEMABSOLUTE MAXIMUM RATINGSSymbol Parameter Value UnitV Power Supply Voltage 30 VPV Logic Supply Volta ..
L6287 ,POWER COMBO DRIVERL6287POWER COMBO DRIVERDESCRIPTIONThe F-VHS Motor Driver COMBO IC includes adouble three phase brus ..
L6287 ,POWER COMBO DRIVERELECTRICAL CHARACTERISTICS (Tj = 0 to125 C; VCC = VS = 5V 5%; VDC = VDL = V = 10 to 18V;unless othe ..
L6301 , The best light source is supported by the best electrode technology
L6301 , The best light source is supported by the best electrode technology
L6301 , The best light source is supported by the best electrode technology
LC3517AM-15 ,150ns, 2048-word x 8-bit CMOS static RAM (SRAM)SANYO SEMICONDUCTOR CORP 53E 1) " 'i"Pi707l, tllnt10'33 8'7T .TSAJ"r--etgr-23--l2-CMOS LSI2048-word ..
LC3517AML-15 ,150ns, 2048-word x 8-bit CMOS static RAM (SRAM)FEATURES. 100 ns (11:3517A-10 series), 120 ns (UB5WA.12 series) and 150 ns (LC3517A-15 series) maxi ..
LC3517AS-15 ,150ns, 2048-word x 8-bit CMOS static RAM (SRAM)BLOCK DIAGRAM+2riir;PIN DESCRIPTION".LLCiiiinECTCiFCT' num» _n“_n“—“——nn—IICiLLCTCEtiCT,SPECI FICAT ..
LC3517ASL-10 ,100ns, 2048-word x 8-bit CMOS static RAM (SRAM)FEATURES. 100 ns (11:3517A-10 series), 120 ns (UB5WA.12 series) and 150 ns (LC3517A-15 series) maxi ..
LC3517ASL-12 ,120ns, 2048-word x 8-bit CMOS static RAM (SRAM)BLOCK DIAGRAM+2riir;PIN DESCRIPTION".LLCiiiinECTCiFCT' num» _n“_n“—“——nn—IICiLLCTCEtiCT,SPECI FICAT ..
LC35256A-10 ,256 K (32768 words x 8 bit) SRAM with OE and CE pinsOrdering number: EN4916ANo. 4916AOverviewThe LC35256A, AS, AM, and AT are 32768 words K8-bits async ..
L6285
3 CHANNELS MULTIPOWER SYSTEM
L62853 CHANNELS MULTIPOWER SYSTEM
ADVANCE DATACHANNEL-A AND CHANNEL-B FOR UNIPO-
LAR STEPPER MOTORS
– LOW SIDE: RDSON = 1.2Ω
– HIGH SIDE ; RDSON = 1.2Ω
CHANNEL-C FOR DC MOTORS
– LOW SIDE: RDSON = 1.7Ω
– HIGH SIDE: RDSON = 1.2Ω
CHOPPING MODE DRIVING FOR C.L. CUR-
RENT CONTROL ON CHA AND CHB AND
O.L. VOLTAGE CONTROL ON CHC.
INTERNAL FOUR DRIVING LATCHES
16 BIT INTERNAL SHIFT REGISTER
DIRECT INTERFACE TO μP
SERIAL DRIVING SEQUENCE LOADING
CMOS COMPATIBLE INPUTS
PRE-ALARM OUTPUT SIGNAL
THERMAL SHUTDOWN
DESCRIPTIONThis Combo Motor Driver uses large scale inte-
gration to incorporate several functions into the
same chip.
1) Two unipolar stepper motor driver
2) A full bridge DC motor driver
3) Serial microprocesor interface
The power output stages are DMOS and the input
can be interfaced to a CMOS Microprocessor
logic.
The phase current in the unipolar stepper motor
windings is controlled by two external sensing re-
sistors in fixed frequency chopping mode. The os-
cillator block provides clocks each other 180° out
of phase to the two stepper motor driver in order
to avoid symultaneous current peaks.
For the DC motor driver is used a bridge; the
RMS voltage to supply this motor is fixed by a
BLOCK DIAGRAM
simple PWM open loop. The 3 motors are control-
led by the micro through 4 latches of 4 bit each.
The loading of these registers is in serial mode.
The I.C. operates at 5V supply for the logic and at
24V supply for the power stages. The packages
are SDIP42 and PLCC44 with 6 pins devoted to
ground and to sink out the heat produced by
power dissipation.
PIN CONNECTION (Top view)
ABSOLUTE MAXIMUM RATINGS
THERMAL DATA (PLCC44)
L6285
PIN DESCRIPTION
L6285
CHANNEL A AND CHANNEL B (UNIPOLAR MOTORS)
CHANNEL C (DC MOTORS) (see Fig. 5)
LOGIC LEVEL
ELECTRICAL CHARACTERISTICS (Tj = 25 °C, Vs = 5V, Vp = 24V unless othewise specified)
L6285
ELECTRICAL CHARACTERISTICS (continued)
OSCILLATOR (see Fig. 6)
INTERFACE TIMING
Note 1: No output loaded; all register to low condition; no reset applied; VP = 26.5V; VS = 5.5V
Note 2: The effect of the internal filter (RC Network) is not considered.
Figure 2: Interface Timing (Serial loading Mode)
Figure 1: Discharge time tdsc or Protection Time
L6285