L4964HT ,HIGH CURRENT SWITCHING REGULATORFeatures of the device include overload protection,soft start, remote inhibit, thermal protection, ..
L4969 ,SYSTEM VOLTAGE REGULATOR WITH FAULT TOLERANT LOW SPEED CAN-TRANSCEIVERL4969SYSTEM VOLTAGE REGULATORWITH FAULT TOLERANT LOW SPEED CAN-TRANSCEIVERPRODUCT PREVIEW■ OPERATIN ..
L497 ,HALL EFFECT PICKUP IGNITION CONTROLLERABSOLUTE MAXIMUM RATINGSSymbol Parameter Value UnitI D.C. Supply current 200 mA3Transient Supply Cu ..
L4970 ,10A SWITCHING REGULATORABSOLUTE MAXIMUM RATINGSSymbol Parameter Value UnitV Input Voltage 55 V9V Input Operating Voltage 5 ..
L4970A ,10A SWITCHING REGULATORL4970A®10A SWITCHING REGULATOR10A OUTPUT CURRENTMULTIPOWER BCD TECHNOLOGY5.1V TO 40V OUTPUT VOLTAGE ..
L4971 ,1.5A STEP DOWN SWITCHING REGULATORL4971®1.5A STEP DOWN SWITCHING REGULATORUP TO 1.5A STEP DOWN CONVERTEROPERATING INPUT VOLTAGE FROM ..
LBC858BLT1G , General Purpose Transistors PNP Silicon
LBE63C , Power TOPLED with Lens Enhanced Optical Power LED (ATON)
LBE67C , Power TOPLED® Enhanced optical Power LED (ATON®)
LBG6SP , Advanced Power TOPLED Enhanced optical Power LED
LBH1000 , 1.6×0.8×0.4 mm(L×W×H) small size surface mount type SMD
LBH1000 , 1.6×0.8×0.4 mm(L×W×H) small size surface mount type SMD
L4964HT
HIGH CURRENT SWITCHING REGULATOR
L4964July 2003
HIGH CURRENT SWITCHING REGULATOR 4 A OUTPUT CURRENT. 5.1 V TO 28 V OUTPUT VOLTAGE RANGE. 0 TO 100 % DUTY CYCLE RANGE. PRECISE (± 3 %) ON-CHIP REFERENCE. SWITCHING FREQUENCY UP TO 120 KHz. VERY HIGH EFFICIENCY (UP TO 90 %). VERY FEW EXTERNAL COMPONENTS. SOFT START. RESET OUTPUT. CURRENT LIMITING. INPUT FOR REMOTE INHIBIT AND SYN-
CHRONUS PWM. THERMAL SHUTDOWN
DESCRIPTIONThe L4964 is a stepdown power switching regulator
delivering 4A at a voltage variable from 5.1V to 28V.
Features of the device include overload protection,
soft start, remote inhibit, thermal protection, a reset
output for microprocessors and a PWM comparator
input for synchronization in multichip configurations.
The L4964 is mounted in a 15-lead Multiwatt plas-
tic power package and requires very few external
components.
Efficient operation at switching frequencies up to
120kHz allows a reduction in the size and cost of ex-
ternal filter components.
PIN CONNECTION (top view)1/13
PIN FUNCTIONS
BLOCK DIAGRAM
L49642/13
CIRCUIT OPERATION (refer to the block diagram)The L4964 is a monolithic stepdown switching regu-
lator providing output voltages from 5.1 V to 28 V
and delivering 4A.
The regulation loop consists of a sawtooth oscillator,
error amplifier, comparator and the output stage. An
error signal is produced by comparing the output
voltage with a precise 5.1 V on-chip reference
(zener zap trimmed to ± 3 %). This error signal is
then compared with the sawtooth signal to generate
the fixed frequency pulse width modulated pulses
which drive the output stage. The gain and fre-
quency stability of the loop can be ajusted by an ex-
ternal RC network connected to pin 9. Closing the
loop directly gives an output voltage of 5.1 V. Higher
voltages are obtained by inserting a voltage divider.
Output overcurrents at switch on are prevented by
the soft start function. The error amplifier output is
initially clamped by the external capacitor Css and al-
lowed to rise, linearly, as this capacitor is charged
by a constant current source.
Output overload protection is provided in the form of
a current limiter. The load current is sensed by an
internal metal resistor connected to a comparator.
When the load current exceeds a preset threshold
this comparator sets a flip flop which disables the
output stage and discharges the soft start capacitor.
A second comparator resets the flip flop when the
voltage across the soft start capacitor has fallen to
0.4 V. The output stage is thus re-enable and the
output voltage rises under contro of the soft start net-
work. If the overload condition is still present the
limiter will trigger again when the thershold current
is reached. The average short circuit current is lim-
ited to a safe value by the dead time introduced by
the soft start network.
The reset circuit generates an output signal when
the supply voltage exceeds a threshold pro-
grammed by an external divider. The reset signal is
generated with a delay time programmed by an ex-
ternal capacitor. When the supply falls below the
threshold the reset output goes low immediately.
The reset output is an open collector.
A TTL - level input is provided for applications such
as remote on/off control. This input is activated by
high level and disables circuit operation. After an in-
hibit the L4964 restarts under control of the soft start
network.
The thermal overload circuit disables circuit opera-
tion when the junction temperature reaches about
150 and has hysteresis to prevent unstable condi-
tions.
Figure 1 : Reset Output Waveforms
L49643/13
Figure 2 : Soft Start Waveforms
Figure 3 : Current Limiter Waveforms
ABSOLUTE MAXIMUM RATINGS
THERMAL DATA
L49644/13
ELECTRICAL CHARACTERISTICS(refer to the test circuits Tj = 25o C, Vi = 25V, unless otherwise specified)
DYNAMIC CHARACTERISTICS (pin 6 to GND unless otherwise specified)
DC CHARACTERISTICS
SOFT START
INHIBIT
ERROR AMPLIFIER
L49645/13
