L4962ES ,1.5A POWER SWITCHING REGULATORELECTRICAL CHARACTERISTICS (continued)Symbol Parameter Test Conditions Min. Typ. Max. UnitDYNAMIC C ..
L4963 ,1.5A SWITCHING REGULATORL4963L4963D®1.5A SWITCHING REGULATOR1.5A OUTPUT LOAD CURRENT5.1 TO 36V OUTPUT VOLTAGE RANGEDISCONTI ..
L4963D ,1.5A SWITCHING REGULATORABSOLUTE MAXIMUM RATINGSSymbolParameter Value UnitSO20 PowerdipViInput Voltage (pin 1 and pin 3 con ..
L4963D013TR ,1.5A SWITCHING REGULATORFeatures of the deviceThe L4963 is mounted in a 12+3+3 lead Powerdipinclude remote inhibit, interna ..
L4963W ,1.5A SWITCHING REGULATORL4963L4963D®1.5A SWITCHING REGULATOR1.5A OUTPUT LOAD CURRENT5.1 TO 36V OUTPUT VOLTAGE RANGEDISCONTI ..
L4964 ,HIGH CURRENT SWITCHING REGULATORFeatures of the device include overload protection,soft start, remote inhibit, thermal protection, ..
LBC856BLT1G , General Purpose Transistors PNP Silicon
LBC857BDW1T1G , Dual General Purpose Transistors
LBC857BLT1G , General Purpose Transistors PNP Silicon
LBC858BLT1G , General Purpose Transistors PNP Silicon
LBE63C , Power TOPLED with Lens Enhanced Optical Power LED (ATON)
LBE67C , Power TOPLED® Enhanced optical Power LED (ATON®)
L4962-L4962ES
1.5A POWER SWITCHING REGULATOR
L49621.5A POWER SWITCHING REGULATOR
1.5A OUTPUT CURRENT
5.1V TO 40V OUTPUT VOLTAGE RANGE
PRECISE (± 2%) ON-CHIP REFERENCE
HIGH SWITCHING FREQUENCY
VERY HIGH EFFICIENCY (UP TO 90%)
VERY FEW EXTERNAL COMPONENTS
SOFT START
INTERNAL LIMITING CURRENT
THERMAL SHUTDOWN
DESCRIPTIONThe L4962 is a monolithic power switching regula-
tor delivering 1.5A at a voltage variable from 5V to
40V in step down configuration.
Features of the device include current limiting, soft
start, thermal protection and 0 to 100% duty cycle
for continuous operating mode.
June 2000
The L4962 is mounted in a 16-lead Powerdip plastic
package and Heptawatt package and requires very
few external components.
Efficient operation at switching frequencies up to
150KHz allows a reduction in the size and cost of
external filter components.
1/16
PIN CONNECTION (Top view)2/16
* Obtained with the GND pins soldered to printed circuit with minimized copper area.
THERMAL DATA
PIN FUNCTIONS
ABSOLUTE MAXIMUM RATINGS
L4962
DYNAMIC CHARACTERISTICS
ELECTRICAL CHARACTERISTICS (Refer to the test circuit, Tj = 25 °C, Vi = 35V, unless otherwise
specified)
PIN FUNCTIONS (cont’d)3/16
L4962
4/16
DYNAMIC CHARACTERISTICS (cont’d)
DC CHARACTERISTICS
SOFT START
ERROR AMPLIFIER
OSCILLATOR
ELECTRICAL CHARACTERISTICS (continued)
L4962
CIRCUIT OPERATION (refer to the block diagram)The L4962 is a monolithic stepdown switching regu-
lator providing output voltages from 5.1V to 40V and
delivering 1.5A.
The regulation loop consists of a sawtooth oscilla-
tor, error amplifier, comparator and the output
stage. An error signal is produced by comparing the
output voltage with a precise 5.1V on-chip refer-
ence (zener zap trimmed to ± 2%).
This error signal is then compared with the sawtooth
signal to generate the fixed frequency pulse width
modulated pulses which drive the output stage.
The gain and frequency stability of the loop can be
adjusted by an external RC network connected to
pin 11. Closing the loop directly gives an output
voltage of 5.1V. Higher voltages are obtained by
inserting a voltage divider.
Output overcurrents at switch on are prevented by
the soft start function. The error amplifier output is
initially clamped by the external capacitor Css and
allowed to rise, linearly, as this capacitor is charged
by a constant current source. Output overload pro-
tection is provided in the form of a current limiter.
The load current is sensed by an internal metal
resistor connected to a comparator. When the load
current exceeds a preset threshold this comparator
sets a flip flop which disables the output stage and
discharges the soft start capacitor. A second com-
parator resets the flip flop when the voltage across
the soft start capacitor has fallen to 0.4V.
The output stage is thus re-enabled and the output
voltage rises under control of the soft start network.
If the overload condition is still present the limiter
will trigger again when the threshold current is
reached. The average short circuit current is limited
to a safe value by the dead time introduced by the
soft start network. The thermal overload circuit dis-
ables circuit operation when the junction tempera-
ture reaches about 150°C and has hysteresis to
prevent unstable conditions.
Figure 1. Soft start waveforms
Figure 2. Current limiter waveforms5/16
L4962
6/16
Figure 4. Quiescent drain
current vs. supply voltage (0%
duty cycle)
Figure 5. Quiescent drain
current vs. supply voltage
(100% duty cycle)
Figure 6. Quiescent drain
current vs. junction tem-
perature (0% duty cycle)
Figure 3. Test and application circuit (Powerdip)
L4962
Figure 7. Quiescent drain
current vs. junction tem-
perature (100% duty cycle)
Figure 8. Reference voltage
(pin 10) vs. Vi rdip) vs. Vi
Figure 9. Reference voltage
(pin 10 ) vs. junction tem-
perature
Figure 10. Open loop fre-
quency and phase re- sponse
of error amplifier
Figure 11. Switching fre-
quency vs. input voltage
Figure 12. Switching fre-
quency vs. junction tem-
perature
Figure 13. Switching fre-
quency vs. R2 (see test circuit)
Figure 15. Load transient
response
Figure 14. Line transient
response7/16
L4962
8/16
Figure 16. Supply voltage
ripple rejection vs. frequency
Figure 17. Dropout voltage
between pin 7 and pin 2 vs.
current at pin 2
Figure 18. Dropout voltage
between pin 7 and 2 vs.
junction temperature
Figure 19. Efficiency vs.
output current
Figure 20. Efficiency vs.
output current
Figure 21. Efficiency vs.
output current
Figure 22. Efficiency vs.
output voltage
Figure 23. Efficiency vs.
output voltage
Figure 24. Maximum allow-
able power dissipation vs. am-
bient temperature (Powerdip)
L4962
