KA3505 ,PC SMPS Supervisory ICKA3505PC SMPS Supervisory IC
KA3511 ,Intelligent Voltage Mode PWM ICKA3511BSIntelligent Voltage Mode PWM IC
KA3511DS ,Intelligent Voltage Mode PWM ICKA3511DSIntelligent Voltage Mode PWM IC
KA3524 ,SMPS ControllerFeatures Description• Complete PWM power control circuit The KA3524 regulating pulse width modu ..
KA3525A ,SMPS ControllerKA3525ASMPS Controller
KA3525AD ,SMPS CONTROLLERELECTRICAL CHARACTERISTICS(V = 20V, T = -35˛ to + 85˛, unless otherwise specified)CC ACharacteristi ..
KRA302 , EPITAXIAL PLANAR PNP TRANSISTOR (SWITCHING, INTERFACE CIRCUIT AND DRIVER CIRCUIT)
KRA302E , EPITAXIAL PLANAR PNP TRANSISTOR
KRA302V , EPITAXIAL PLANAR PNP TRANSISTOR
KRA303 , EPITAXIAL PLANAR PNP TRANSISTOR (SWITCHING, INTERFACE CIRCUIT AND DRIVER CIRCUIT)
KRA303 , EPITAXIAL PLANAR PNP TRANSISTOR (SWITCHING, INTERFACE CIRCUIT AND DRIVER CIRCUIT)
KRA303E , EPITAXIAL PLANAR PNP TRANSISTOR
KA3505
PC SMPS Supervisory IC
Features PC Power Supply Output Monitor Circuitry Few External Components Over Voltage Protection for 3.3V / 5V / 12V Output Under V oltage Protection for 3.3V / 5V / 12V Output
With Delay Time Over Current Protection for 3.3V / 5V / 12V Output With
Delay Time Fault Protection Output With Open Collector Output Power Supply On/Off Delay Time Control (PSON) Power Good Signal Generator With Hysteresis Open Collector PG Output 300ms Power Good Delay Current Sense Setting Function With RI Latch Function Controlled by PSON and Protection Input 16-Pin Dual In-line Package
FPO (Fault Protection Output)Fault Protection Output indicates the fault condition as pro-tection signal. When fault state occurs, the main power is to be turned-off and the PGO signal goes LOW.
NORMAL = "LOW", FAULT = "HIGH"
PGO (Power Good Output)Power Good Signal Generator is to monitor the voltage level of power supply for safe operation of a microprocessor hav-ing some delay time at turn-on. The delay time is pro-grammed by a timing capacitor connected to TPG pin of KA3505. The power good output should be low state before the output voltage is out of regulation at turn-off.
NORMAL = "HIGH", FAULT = "LOW"
DescriptionThe KA3505 is complete output supervisory circuitry intend-ed for use in the secondary side of the switched mode power supply. It provides all the functions necessary to monitor and control the output of the power supply system. Power good signal generator, Remote on and off control, some precision protection features against over-voltage, under-voltage and over-current are implemented. It directly senses all the output rails for OVP and UVP without any external dividers. As for output control, Power Good Output (PGO) and Fault Protec-tion Output (FPO) are also included. Utilizing a minimum number of external components, the KA3505 offers a simple and cost effective solution, greatly reducing PCB board space for power supply system.
OCP (Over Current Protection)It has precision OCP functions for +3.3V, +5V, +12V out-puts. The block is made up of three comparators with current source setting function. Two inputs of each OCP comparator are connected to both sides of output inductor that is located in the secondary output of SMPS.
OVP (Over Voltage Protection)It has OVP functions for +3.3V, +5V, +12V outputs. The cir-cuit is made up of a comparator with three detecting inputs.
UVP (Under Voltage Protection)It also has UVP functions for +3.3V, +5V, +12V outputs. The block is made up of a comparator with three detecting inputs.
Remote ON/OFFRemote on/off section is used to control SMPS externally. If a high signal is supplied to the remote on/off input, FPO sig-nal becomes a high state and all secondary outputs are
grounded. The remote on/off signal is transferred with some on-delay and off-delay time of 8ms, 24ms respectively with
0.1mF external capacitor.
