FAN5607HMPX ,LED Driver with Adaptive Charge Pump DC/DC ConverterFeatures Description• Parallel LED Driver Supports all Forward Voltages The FAN5607 generates regul ..
FAN5608HMPX ,Serial/Parallel LED Driver with Current-Regulated, Step-Up DC/DC ConverterFeatures Description• Two Independent Channels Drive up to Six LEDs per The FAN5608 LED driver gene ..
FAN5608HMPX ,Serial/Parallel LED Driver with Current-Regulated, Step-Up DC/DC Converter FAN5608Serial/Parallel LED Driver with Current-Regulated, Step-Up DC/DC Co ..
FAN5608HMPX ,Serial/Parallel LED Driver with Current-Regulated, Step-Up DC/DC ConverterFeatures Description• Two Independent Channels Drive up to Six LEDs per The FAN5608 LED driver gene ..
FAN5608MPX ,Serial/Parallel LED Driver with Current-Regulated, Step-Up DC/DC Converter FAN5608Serial/Parallel LED Driver with Current-Regulated, Step-Up DC/DC Co ..
FAN5609MPX ,LED Driver with Adaptive Charge Pump DC/DC ConverterApplications• Parallel LED Driver Supports All Forward Voltages • Cell Phones• Adaptive V Adjustmen ..
FJA13009TU ,NPN Silicon TransistorFJA13009FJA13009High Voltage Switch Mode
FJA13009TU ,NPN Silicon TransistorApplications High Speed Switching Suitable for Switching Regulator and Motor ControlTO-3P11.Base ..
FJA4210 ,PNP Epitaxial Silicon TransistorFJA4210FJA4210Audio Power Amplifier• High Current Capability : I = -10AC• High Power Dissipation•Wi ..
FJA4213OTU ,PNP Epitaxial Silicon TransistorFJA4213FJA4213Audio Power Amplifier High Current Capability I = -15AC High Power DissipationWide ..
FJA4213RTU ,PNP Epitaxial Silicon TransistorFJA4213FJA4213Audio Power Amplifier High Current Capability I = -15AC High Power DissipationWide ..
FJA4310 ,Audio Power AmplifierFJA4310FJA4310Audio Power Amplifier• High Current Capability : I =10AC• High Power Dissipation•Wide ..
FAN5607HMPX
LED Driver with Adaptive Charge Pump DC/DC Converter
Features Parallel LED Driver Supports all Forward Voltages Adaptive V
OUT
Adjustment to the Highest Diode V oltage Internally Matched LED Current Sources Built-in Charge Pump has Three Modes of Operation: 1X, 1.5X, and 2X Mode Up to 93% Efficiency Low EMI, Low Ripple Up to 120mA Output Current ( ) External Resistor to Set Maximum (100%) LED Current Enable Input Can be Duty-Cycle-Modulated to Control
LED Current Level Between 0 and 100% 2.4V to 5.5V Input Voltage Range
< 1µA in Shutdown Mode 1MHz Operating Frequency Shutdown Isolates Output from Input Soft-Start Limits Inrush Current Short Circuit Protection Minimal External Components Needed Available in a 4x4mm 16-lead MLP Package
Applications Cell Phones Handheld Computers PDA, DSC, MP3 Players Keyboard Backlight LED Displays
DescriptionThe FAN5607 generates regulated output current from a bat-
tery with input voltage varying between 2.7V to 5.5V.
Switch reconfiguration and fractional switching techniques
are utilized to achieve high efficiency over the entire input
voltage range. A proprietary internal circuitry continuously
monitors each LED current loop and automatically adjusts
the generated output DC voltage to the lowest minimum
value required by the LED having the highest forward volt-
age. This adaptive nature of the FAN5607 eliminates the
need for LED pre-selection (matching) and ensures opera-
tion at high efficiency. When the input voltage is sufficiently
high to sustain the programmed current level in the LEDs,
the FAN5607 re-configures itself to operate as a linear regu-
lator, and the DC-DC converter is turned off. Only two 0.1µF
to 1µF bucket capacitors and two 4.7µF input/output capaci-
tors are needed for proper operation. LED current can be
programmed using an external resistor. The resistor sets the
maximum LED current and a PWM signal applied to the
enable pin can modulate that current level between 0mA
(off) and the maximum level.
Soft-start circuitry prevents excessive current draw during
power on. The device has built-in short circuit protection.
The device is available in 4x4mm 16-lead MLP package. 30mA×
