DS9503 ,ESD Protection Diode with ResistorsFEATURES SYMBOL AND CONVENTI Zener characteristic with voltage snap–back C to protect against ..
DS9503P ,ESD Protection Diode with Resistors
DS9503P. ,ESD Protection Diode with Resistors
DS9503P+ ,ESD Protection Diode with ResistorsFEATURES SYMBOL AND CONVENTI Zener characteristic with voltage snap–back C to protect against ..
DS9503P+ ,ESD Protection Diode with Resistors19-4699; 7/09 DS9503 ESD Protection Diode with Resistors ONS SPECIAL
DS96172CN ,RS-485/RS-422 Quad Differential Line Driversfeatures separate active high Enables for eachdriver pair. Compatible RS-485 receivers, transceiver ..
ED1402 ,NPN general purpose transistor
ED1402B ,NPN general purpose transistor
ED1402B ,NPN general purpose transistor
ED1402C ,NPN general purpose transistor
ED1402C ,NPN general purpose transistor
ED1402E ,NPN general purpose transistor
DS9503
ESD Protection Diode with Resistors
SPECIAL FEATURES Zener characteristic with voltage snap–back
to protect against ESD hits High avalanche voltage, low leakage and low
capacitance avoid signal attenuation Compatible to all 5V logic families Space saving, low inductance TSOC surface
mount package On–chip 5resistors for isolation at both
anode and cathode terminals Industrial temperature range
DS9503
ESD Protection Diode with Resistors
SYMBOL AND CONVENTIONS
PACKAGE OUTLINE VCA
TSOC SURFACE MOUNT PACKAGE
6 1 2 3
TOP VIEW
SIDE VIEW
19-4699; 7/09
ORDERING INFORMATION DS9503P+ 6-lead TSOC package
DS9503P+T&R 6-lead TSOC package
+Denotes a lead(Pb)-free/RoHS-compliant package.
T&R = Tape and reel.
DESCRIPTION This DS9503 is designed as an ESD protection device for 1–Wire MicroLAN interfaces. In contrast to the
DS9502, the DS9503 includes two 5isolation resistors on chip. Although 5are negligible during
communication, they represent a high impedance relative to the conducting diode during an ESD event.
Thus, the diode absorbs the energy while the resistors further isolate and protect the circuit at the other
side of the package. If used with circuits that already have a strong ESD–protection at their I/O port, the
ESD protection level is raised to more that 27 kV (IEC 801–2 Reference model). In case of abnormal
ESD hits beyond its maximum ratings the DS9503 will eventually fail “short” thus preventing further
damage.
During normal operation the DS9503 behaves like a regular Zener Diode. When the voltage exceeds the
trigger voltage, the I/V characteristic of the device will “snapback” allowing the same or higher amount
of current to flow, but at a significantly lower voltage. As long as a minimum current or voltage is
maintained, the device will stay in the “snapback mode”. If the voltage or the current falls below the
holding voltage or holding current, the device will abruptly change to its normal mode and conduct only a
DS9503
DC CHARACTERISTICS Figure 1 VCA/V
IC/A
1 2 3 4 5 6 7 8 9 10 11
1.0
0.8
0.6
0.4
0.2
I-TRIGGER
V-TRIGGER VAV
SEE DETAIL DRAWING
DC CHARACTERISTICS DETAIL DRAWING Figure 2
TEST PULSE WAVEFORM Figure 3
TYPICAL APPLICATION Figure 4 DS9503
ABSOLUTE MAXIMUM RATINGS* Operating Temperature –40°C to +85°C
Storage Temperature –55°C to +125°C
Soldering Temperature 260°C for 10 seconds
Continuous DC Current Through Package 80 mA This is a stress rating only and functional operation of the device at these or any other conditions
above those indicated in the operation sections of this specification is not implied. Exposure to
absolute maximum rating conditions for extended periods of time may affect reliability
ELECTRICAL CHARACTERISTICS (-40C to +85C)
PARAMETER SYMBOLMIN TYP MAX UNITS NOTES Leakage Current IL 30 100 nA 1
Avalanche Voltage VAV 7.4 11.05 V 2,3
Trigger Voltage VTRIGGER 10 11 V 2, 4
Trigger Current ITRIGGER 1000 mA 4
Holding Voltage VHOLD 5.5 V 2,4
Holding Current IHOLD 11 mA 4
Forward Voltage (-10 mA) VF -0.7 -0.8 V 5
Forward Current (-0.7V) IF -10 -100 mA 5
Maximum Peak Current IPP 2.0 A 6
Continuous Current Through Diode ICC 80 mA
Isolation Resistance RI 5
CAPACITANCE (tA=25C)
PARAMETER SYMBOLMIN TYP MAX UNITS NOTES Junction Capacitance (5V) CJ5 40 pF 2
Junction Capacitance (0V) CJ0 70 pF 2
THERMAL RESISTANCE
PARAMETER SYMBOLMIN TYP MAX UNITS NOTES Junction To Package RJC 75 K/W
Junction To Ambient RJA 200 K/W
NOTES: 1. At 7.0V.
2. All voltages are referenced from Cathode to Anode.
3. At 0.3 A.
4. Not production tested, guaranteed by design.
5. Typical values at room temperature.
6. See pulse specification.
DS9503
REVISION HISTORY
REVISION
DATE DESCRIPTION PAGES
CHANGED Added “lead-free” note to the Ordering Information table. 1
Fixed the X/Y scale in Figure 1. 2
In the Electrical Characteristics table, changed the VAV specification maximum
value to 11V; the VTRIGGER specification typical value to 10V and maximum value
to 11V; the ITRIGGER specification typical value to a blank; and the IHOLD
specification minimum value to an 11mA. 072209
Added note 4 (“Not production tested, guaranteed by design”) to the VTRIGGER,
ITRIGGER, VHOLD, and IHOLD specifications in the Electrical Characteristics table. 3
This datasheet has been :
www.ic-phoenix.com
Datasheets for electronic components.
