DS26502LN+ ,T1/E1/J1/64KCC BITS ElementApplications BITS Timing Accepts 16.384MHz, 12.8MHz, 8.192MHz, Rate Conversion 4.096MHz, 2.048MHz ..
DS26502LN+ ,T1/E1/J1/64KCC BITS ElementFUNCTIONAL DESCRIPTION........30 7.2 SPI SERIAL PORT INTERFACE
DS26503 ,T1/E1/J1 BITS ElementFEATURES Fast Transmitter Output Disable through Device Accepts 8kHz and 19.44MHz References ..
DS26503 ,T1/E1/J1 BITS ElementFEATURES The DS26503 is a building-integrated timing- G.703 2048kHz Synchronization Interface sup ..
DS26503L+ ,T1/E1/J1 BITS ElementFEATURES The DS26503 is a building-integrated timing- G.703 2048kHz Synchronization Interface Comp ..
DS26503LN+ ,T1/E1/J1 BITS ElementAPPLICATIONS Clock BITS Timing 8-Bit Parallel Control Port, Multiplexed or Rate Conversion Nonmul ..
E53NA50 ,NABSOLUTE MAXIMUM RATINGSSymbol Parameter Value UnitV Drain-source Voltage (V =0) 500 VDS GSV 500 VD ..
EA2-12 ,COMPACT AND LIGHTWEIGHTAPPLICATIONSElectronic switching systems, PBX, key telephone systems, automatic test equipment and ..
EA2-12NU ,COMPACT AND LIGHTWEIGHTFEATURESª Low power consumptionª Compact and light weightª 2 form c contact arrangementª Low magnet ..
EA2-12S ,COMPACT AND LIGHTWEIGHTFEATURESª Low power consumptionª Compact and light weightª 2 form c contact arrangementª Low magnet ..
EA2-12TNU ,COMPACT AND LIGHTWEIGHTAPPLICATIONSElectronic switching systems, PBX, key telephone systems, automatic test equipment and ..
EA2-4.5NU ,COMPACT AND LIGHTWEIGHTAPPLICATIONSElectronic switching systems, PBX, key telephone systems, automatic test equipment and ..
DS26502L+-DS26502LN+
T1/E1/J1/64KCC BITS Element
GENERAL DESCRIPTION The DS26502 is a building-integrated timing-
supply (BITS) clock-recovery element. It also
functions as a basic T1/E1 transceiver. The
receiver portion can recover a clock from T1,
E1, 64kHz composite clock (64KCC), and
6312kHz synchronization timing interfaces. In
T1 and E1 modes, the Synchronization Status
Message (SSM) can also be recovered. The
transmit portion can directly interface to T1, E1,
or 64KCC synchronization interfaces as well as
source the SSM in T1 and E1 modes. The
DS26502 can translate between any of the
supported inbound synchronization clock rates to
any supported outbound rate. A separate output
is provided to source a 6312kHz clock. The
device is controlled through a parallel, serial, or
hardware controller port.
APPLICATIONS BITS Timing
Rate Conversion
ORDERING INFORMATION
PART TEMP RANGE PIN-PACKAGE DS26502L 0°C to +70°C 64 LQFP
DS26502LN -40°C to +85°C 64 LQFP
FEATURES � G.703 2048kHz Synchronization Interface
Compliant � G.703 64kHz Centralized (Option A) and
Codirectional Timing Interface Compliant � G.703 Appendix II 64kHz and 6312kHz
Japanese Synchronization Interface
Compliant � Interfaces to Standard T1/J1 (1.544MHz) and
E1 (2.048MHz) � Interface to CMI-Coded T1/J1 and E1 � Short- and Long-Haul Line Interface � Transmit and Receive T1 and E1 SSM
Messages with Message Validation � T1/E1 Jitter Attenuator with Bypass Mode � Fully Independent Transmit and Receive
Functionality � Internal Software-Selectable Receive- and
Transmit-Side Termination for
75Ω/100Ω/110Ω/120Ω T1, E1, and
Composite Clock Interfaces � Monitor Mode for Bridging Applications � Accepts 16.384MHz, 12.8MHz, 8.192MHz,
4.096MHz, 2.048MHz, or 1.544MHz Master
Clock � 64kHz, 8kHz, and 400Hz Outputs in
Composite Clock Mode � 8-Bit Parallel Control Port, Multiplexed or
Nonmultiplexed, Intel or Motorola � Serial (SPI) Control Port � Hardware Contr-ol Mode � Provides LOS, AIS, and LOF Indications
Through Hardware Output Pins � Fast Transmitter-Output Disable Through
Device Pin for Protection Switching � IEEE 1149.1 JTAG Boundary Scan � 3.3V Supply with 5V Tolerant Inputs and
Outputs
DS26502
T1/E1/J1/64KCC BITS Element
DESIGN KIT AVAILABLE
DS26502 T1/E1/J1/64KCC BITS Element
TABLE OF CONTENTS
1. FEATURES.......................................................................................................................7 1.1 GENERAL.....................................................................................................................................7
1.2 LINE INTERFACE...........................................................................................................................7
1.3 JITTER ATTENUATOR (T1/E1 MODES ONLY)..................................................................................7
1.4 FRAMER/FORMATTER...................................................................................................................8
1.5 TEST AND DIAGNOSTICS...............................................................................................................8
1.6 CONTROL PORT............................................................................................................................8
2. SPECIFICATIONS COMPLIANCE...................................................................................9
3. BLOCK DIAGRAMS.......................................................................................................11
4. PIN FUNCTION DESCRIPTION.....................................................................................14 4.1 TRANSMIT PLL...........................................................................................................................14
4.2 TRANSMIT SIDE..........................................................................................................................14
4.3 RECEIVE SIDE............................................................................................................................15
4.4 CONTROLLER INTERFACE............................................................................................................16
4.5 JTAG.........................................................................................................................................21
4.6 LINE INTERFACE.........................................................................................................................21
4.7 POWER......................................................................................................................................22
5. PINOUT...........................................................................................................................23
6. HARDWARE CONTROLLER INTERFACE....................................................................26 6.1 TRANSMIT CLOCK SOURCE.........................................................................................................26
6.2 INTERNAL TERMINATION..............................................................................................................26
6.3 LINE BUILD-OUT.........................................................................................................................27
6.4 RECEIVER OPERATING MODES....................................................................................................27
6.5 TRANSMITTER OPERATING MODES..............................................................................................28
6.6 MCLK PRE-SCALER...................................................................................................................28
6.7 OTHER HARDWARE CONTROLLER MODE FEATURES....................................................................29
7. PROCESSOR INTERFACE............................................................................................30 7.1 PARALLEL PORT FUNCTIONAL DESCRIPTION................................................................................30
7.2 SPI SERIAL PORT INTERFACE FUNCTIONAL DESCRIPTION............................................................30
7.2.1 Clock Phase and Polarity.....................................................................................................................30
7.2.2 Bit Order...............................................................................................................................................30
7.2.3 Control Byte.........................................................................................................................................30
7.2.4 Burst Mode...........................................................................................................................................30
7.2.5 Register Writes.....................................................................................................................................31
7.2.6 Register Reads....................................................................................................................................31
7.3 REGISTER MAP...........................................................................................................................32
7.3.1 Power-Up Sequence............................................................................................................................34
7.3.2 Test Reset Register.............................................................................................................................34
7.3.3 Mode Configuration Register...............................................................................................................35
7.4 INTERRUPT HANDLING................................................................................................................38
7.5 STATUS REGISTERS....................................................................................................................38
7.6 INFORMATION REGISTERS...........................................................................................................39
7.7 INTERRUPT INFORMATION REGISTERS.........................................................................................39
8. T1 FRAMER/FORMATTER CONTROL REGISTERS....................................................40 8.1 T1 CONTROL REGISTERS............................................................................................................40
DS26502 T1/E1/J1/64KCC BITS Element
9.2 E1 INFORMATION REGISTERS......................................................................................................48
10. I/O PIN CONFIGURATION OPTIONS............................................................................52
11. T1 SYNCHRONIZATION STATUS MESSAGE..............................................................55 11.1 T1 BIT-ORIENTED CODE (BOC) CONTROLLER............................................................................55
11.2 TRANSMIT BOC.........................................................................................................................55
11.3 RECEIVE BOC...........................................................................................................................56
12. E1 SYNCHRONIZATION STATUS MESSAGE..............................................................64 12.1 SA/SI BIT ACCESS BASED ON CRC4 MULTIFRAME......................................................................64
12.2 ALTERNATE SA/SI BIT ACCESS BASED ON DOUBLE-FRAME.........................................................74
13. LINE INTERFACE UNIT (LIU)........................................................................................77 13.1 LIU OPERATION.........................................................................................................................78
13.2 LIU RECEIVER...........................................................................................................................78
13.2.1 Receive Level Indicator........................................................................................................................78
13.2.2 Receive G.703 Section 13 Synchronization Signal.............................................................................79
13.2.3 Monitor Mode.......................................................................................................................................79
13.3 LIU TRANSMITTER.....................................................................................................................79
13.3.1 Transmit Short-Circuit Detector/Limiter................................................................................................80
13.3.2 Transmit Open-Circuit Detector...........................................................................................................80
13.3.3 Transmit BPV Error Insertion...............................................................................................................80
13.3.4 Transmit G.703 Section 10 Synchronization Signal (E1 Mode)...........................................................80
13.4 MCLK PRE-SCALER..................................................................................................................80
13.5 JITTER ATTENUATOR..................................................................................................................80
13.6 CMI (CODE MARK INVERSION) OPTION.......................................................................................81
13.7 LIU CONTROL REGISTERS..........................................................................................................82
13.8 RECOMMENDED CIRCUITS..........................................................................................................90
14. LOOPBACK CONFIGURATION.....................................................................................95
15. 64KHZ SYNCHRONIZATION INTERFACE....................................................................96 15.1 RECEIVE 64KHZ SYNCHRONIZATION INTERFACE OPERATION.......................................................96
15.2 TRANSMIT 64KHZ SYNCHRONIZATION INTERFACE OPERATION.....................................................97
16. 6312KHZ SYNCHRONIZATION INTERFACE................................................................98 16.1 RECEIVE 6312KHZ SYNCHRONIZATION INTERFACE OPERATION...................................................98
16.2 TRANSMIT 6312KHZ SYNCHRONIZATION INTERFACE OPERATION.................................................98
17. JTAG BOUNDARY SCAN ARCHITECTURE AND TEST ACCESS PORT...................99 17.1 INSTRUCTION REGISTER...........................................................................................................103
17.2 TEST REGISTERS.....................................................................................................................104
17.2.1 Boundary Scan Register....................................................................................................................104
17.2.2 Bypass Register.................................................................................................................................104
17.2.3 Identification Register.........................................................................................................................104
18. FUNCTIONAL TIMING DIAGRAMS.............................................................................107 18.1 PROCESSOR INTERFACE...........................................................................................................107
18.1.1 Parallel Port Mode..............................................................................................................................107
18.1.2 SPI Serial Port Mode..........................................................................................................................107
19. OPERATING PARAMETERS.......................................................................................110
20. AC TIMING PARAMETERS AND DIAGRAMS............................................................112 20.1 MULTIPLEXED BUS...................................................................................................................112
DS26502 T1/E1/J1/64KCC BITS Element
20.4 RECEIVE SIDE AC CHARACTERISTICS.......................................................................................120
20.5 TRANSMIT SIDE AC CHARACTERISTICS.....................................................................................122
21. REVISION HISTORY....................................................................................................124
22. PACKAGE INFORMATION..........................................................................................125 22.1 64-PIN LQFP (56-G4019-001).................................................................................................125
DS26502 T1/E1/J1/64KCC BITS Element
LIST OF FIGURES Figure 3-1. Block Diagram........................................................................................................................11
Figure 3-2. Loopback Mux Diagram (T1/E1 Modes Only)........................................................................12
Figure 3-3. Transmit PLL Clock Mux Diagram..........................................................................................12
Figure 3-4. Master Clock PLL Diagram....................................................................................................13
Figure 13-1. Basic Network Connection...................................................................................................77
Figure 13-2. Typical Monitor Application..................................................................................................79
Figure 13-3. CMI Coding..........................................................................................................................81
Figure 13-4. Software-Selected Termination, Metallic Protection.............................................................90
Figure 13-5. Software-Selected Termination, Longitudinal Protection.....................................................91
Figure 13-6. E1 Transmit Pulse Template................................................................................................92
Figure 13-7. T1 Transmit Pulse Template................................................................................................92
Figure 13-8. Jitter Tolerance (T1 Mode)...................................................................................................93
Figure 13-9. Jitter Tolerance (E1 Mode)...................................................................................................93
Figure 13-10. Jitter Attenuation (T1 Mode)...............................................................................................94
Figure 13-11. Jitter Attenuation (E1 Mode)..............................................................................................94
Figure 15-1. 64kHz Composite Clock Mode Signal Format......................................................................96
Figure 17-1. JTAG Functional Block Diagram..........................................................................................99
Figure 17-2. TAP Controller State Diagram............................................................................................102
Figure 18-1. SPI Serial Port Access, Read Mode, CPOL = 0, CPHA = 0...............................................107
Figure 18-2. SPI Serial Port Access, Read Mode, CPOL = 1, CPHA = 0...............................................107
Figure 18-3. SPI Serial Port Access, Read Mode, CPOL = 0, CPHA = 1...............................................107
Figure 18-4. SPI Serial Port Access, Read Mode, CPOL = 1, CPHA = 1...............................................108
Figure 18-5. SPI Serial Port Access, Write Mode, CPOL = 0, CPHA = 0...............................................108
Figure 18-6. SPI Serial Port Access, Write Mode, CPOL = 1, CPHA = 0...............................................108
Figure 18-7. SPI Serial Port Access, Write Mode, CPOL = 0, CPHA = 1...............................................109
Figure 18-8. SPI Serial Port Access, Write Mode, CPOL = 1, CPHA = 1...............................................109
Figure 20-1. Intel Bus Read Timing (BTS = 0 / BIS[1:0] = 00)...............................................................113
Figure 20-2. Intel Bus Write Timing (BTS = 0 / BIS[1:0] = 00)................................................................113
Figure 20-3. Motorola Bus Timing (BTS = 1 / BIS[1:0] = 00)..................................................................114
Figure 20-4. Intel Bus Read Timing (BTS = 0 / BIS[1:0] = 01)................................................................116
Figure 20-5. Intel Bus Write Timing (BTS = 0 / BIS[1:0] = 01)................................................................116
Figure 20-6. Motorola Bus Read Timing (BTS = 1 / BIS[1:0] = 01)........................................................117
Figure 20-7. Motorola Bus Write Timing (BTS = 1 / BIS[1:0] = 01).........................................................117
Figure 20-8. SPI Interface Timing Diagram, CPHA = 0, BIS[1:0] = 10...................................................119
Figure 20-9. SPI Interface Timing Diagram, CPHA = 1, BIS[1:0] = 10...................................................119
Figure 20-10. Receive Timing, T1, E1, 64KCC Mode............................................................................121
Figure 20-11. Transmit Timing, T1, E1, 64KCC Mode...........................................................................123
