DS2502-E64 ,IEEE EUI-64 Node Address Chip19-5072; 12/09 DS2502-E64IEEE EUI-64 Node Address Chip
DS2502-E64+ ,IEEE EUI-64 Node Address Chip19-5072; 12/09 DS2502-E64IEEE EUI-64 Node Address Chip
DS2502P ,1 kbit Add-Only MemoryDS2502/5/6-UNWTMUniqueWare Add-Only Memorywww.dalsemi.comSPECIAL
DS2502P ,1 kbit Add-Only MemoryDS2502/5/6-UNWTMUniqueWare Add-Only Memorywww.dalsemi.comSPECIAL
DS2502P ,1 kbit Add-Only MemoryDS2502/5/6-UNWTMUniqueWare Add-Only Memorywww.dalsemi.comSPECIAL
DS2502P+ ,1Kb Add-Only MemoryFEATURES PIN ASSIGNMENT§ 1024 bits Electrically Programmable ReadTO-92NC 1 8 NCOnly Memory (EPROM) ..
E53NA50 ,NABSOLUTE MAXIMUM RATINGSSymbol Parameter Value UnitV Drain-source Voltage (V =0) 500 VDS GSV 500 VD ..
EA2-12 ,COMPACT AND LIGHTWEIGHTAPPLICATIONSElectronic switching systems, PBX, key telephone systems, automatic test equipment and ..
EA2-12NU ,COMPACT AND LIGHTWEIGHTFEATURESª Low power consumptionª Compact and light weightª 2 form c contact arrangementª Low magnet ..
EA2-12S ,COMPACT AND LIGHTWEIGHTFEATURESª Low power consumptionª Compact and light weightª 2 form c contact arrangementª Low magnet ..
EA2-12TNU ,COMPACT AND LIGHTWEIGHTAPPLICATIONSElectronic switching systems, PBX, key telephone systems, automatic test equipment and ..
EA2-4.5NU ,COMPACT AND LIGHTWEIGHTAPPLICATIONSElectronic switching systems, PBX, key telephone systems, automatic test equipment and ..
DS2502-E64
IEEE EUI-64 Node Address Chip
FEATURES IEEE-approved factory programmed 64-bit
node address chip (EUI-64) with 768 bits
user-programmable OTP-EPROM
communicates with the economy of one
signal plus ground Meets the node identification requirements of
IEEE Standard 1394-1995 (FireWire) Unique, factory-lasered and tested 64-bit
registration number assures absolute
traceability because no two parts are alike Built-in multidrop controller ensures
compatibility with other 1-Wire products Device is an “add only” memory where
additional data can be programmed into
EPROM without disturbing existing data Reduces control, address, data, power and
programming signals to a single pin Directly connects to a single port pin of a
microprocessor and communicates at up to
16.3k bits per second Presence detector acknowledges when reader
first applies voltage Low cost TO-92 or TSOC surface mount
packages Reads over a wide voltage range of 2.8V to
6.0V from -40°C to +85°C; programs at
11.5V to 12.0V from -40°C to +50°C
3 2 1
PIN ASSIGNMENT
ORDERING INFORMATION
PART TEMP
RANGE
PIN-
PACKAGE DS2502-E64+ -40°C to +85°C 3 TO-92
DS2502P-E64+ -40°C to +85°C 6 TSOC
+ Denotes a lead(Pb)-free/RoHS-compliant package.
FireWireTM is a trademark of Apple Computer, Inc.
DESCRIPTION The DS2502-E64 is a variant of the DS2502 1024-bit Add-Only Memory. It differs from the standard
DS2502 in its custom ROM family code 89h, and the UniqueWare Identifier 5E7h in place of the upper
12 bits of the standard ROM serialization field. Otherwise, the electrical and logical behavior is identical
to that of the DS2502. For technical details please refer to the DS2502 data sheet.
DS2502-E64
IEEE EUI-64 Node Address Chip
SIDE VIEW
TOP VIEW
THE DOT MARKS PIN 1
TSOC PACKAGE
E 6 4
2 5 0 2
YYWW
DATANCNCNC
GND
YYWW = DATE CODE
RR = DIE REVISION CODE
CCCCCC = COUNTRY CODE
BOTTOM VIEW
TO-92
DS2502-E64
YYWWRR
CCCCCC
GND
DATA
NC 31
19-5072; 12/09
DS2502-E64
The first 32 bytes of the DS2502-E64’s EPROM memory contain a globally unique 64-bit node address
(EUI-64) and are write-protected. The data structure follows the conventions of UniqueWare devices
using Default Data Structure (Figure 1). This format is also known as UDP (universal data packet) and is
commonly used in 1-Wire APIs. Therefore, if using one of those APIs one can call a high level function
to read and verify the inverted CRC16. The UDP is defined in Application Note 114, 1-Wire File
Structure, and the APIs can be found in the 1-Wire Software Development Kits.
Figure 1. EUI-64 NODE ADDRESS CHIP DATA STRUCTURE CRC16
COMPANY ID VALUE EXTENSION ID VALUE PROJECT ID (UNUSED)
MSB LSB MSB LSB MSB LSB MSB LSB
LENGTH 17 BYTES
FFh 2 BYTES 3 BYTES CONSTANT
006035h 5 BYTES SERIALIZATION 4 BYTES CONSTANT
00001128h
1 BYTE
0Ch
HIGH ADDRESS LOW ADDRESS
The data record starts with a length byte (0Ch) and the 4-byte UniqueWare Project ID 00001128h. The
next eight bytes contain the EUI-64 global identifier (node address) which consists of an incrementing
40-bit extension identifier and the IEEE-assigned 24-bit company ID value 006035h. An inverted 16-bit
CRC ends the data record. The remaining bytes of the 32-byte memory page remain unprogrammed.
Neither the 40–bit extension identifier nor the 24-bit company ID are related to the 64-bit ROM
registration number. The ROM registration number is used to provide a unique address to access the
DS2502-E64 when multidropped on a 1-Wire bus.
EXAMPLE Assume that a manufacturer’s company ID value is 006035h and the 40-bit extension identifier is
234567ABCDh. The EUI-64 value generated from these two numbers is 006035234567ABCDh, whose
byte and bit representations are illustrated in Figure 2.
Figure 2. SAMPLE EUI-64 VALUE MOST SIGNIFICANTBYTE LEAST SIGNIFICANTBYTE
00 60 35 23 45 67 AB CD HEX
0000 0000 0110 0000 0011 0101 0010 0011 0100 0101 0110 0111 1010 1011 1100 1101 BINARY
MOST SIGNIFICANT BIT LEAST SIGNIFICANT BIT
This information is stored in the DS2502-E64 as 64-bit number with the least significant byte at the lower
address. Including the length byte and the inverted CRC, the complete set of data is shown in Figure 3.
Figure 3. PHYSICAL ADDRESS AND DATA MAPPING INSIDE THE DEVICE ADDRESS 0E 0D 0C 0B 0A 09 08 07 06 05 04 03 02 01 00
DATA 3E FF 00 60 35 23 45 67 AB CD 00 00 11 28 0C
DS2502-E64
The four bytes at memory addresses 01h to 04h contain the UniqueWare Project ID 00001128h. The two
bytes at addresses 0Dh and 0Eh are the inverted 16-bit CRC over the length byte, Project ID and EUI-64
value. The least significant byte of the CRC is stored at address 0Dh. This CRC is generated according to
the standardized CRC16 polynomial function X16 + X15 + X2 + 1. For more details on generating CRC
values including examples in both hardware and software, see Application Note 27, Understanding and
Using Cyclic Redundancy Checks with Maxim iButton Products.
The contents of the memory address range 0Fh to 1Fh is FFh. These cells cannot be altered since the
whole memory page is write-protected. The memory range from 20h to 7Fh, however, is user-
programmable. It can be write-protected by programming the corresponding write-protect bit in the status
memory of the DS2502-E64.
DS2502-E64
REVISION HISTORY
REVISION
DATE DESCRIPTION PAGES
CHANGED Changed the Ordering Information to lead free. 1
Included an explanation of “Default Data Structure” above Figure 1. 2
Emphasized that the 16-bit CRC is inverted. 2
Inserted actual CRC value to Figure 3. 2
Reformatted Figures 1 to 3. 2
Removed reference to the Book of iButton Standards. 2
12/09
Changed notation of hexadecimal numbers from 16 or H to h. 1, 2, 3
This datasheet has been :
www.ic-phoenix.com
Datasheets for electronic components.
