CGY50 ,Broadband MMIC Amplifier GaAs MMIC CGY 50____________________________________________________________________ ..
CGY60 ,GaAs MMIC (Low noise preamplifier for mobile communication PCN, DECT, GSM in 2.7V to 6V systems) GaAs MMIC CGY 60Data Sheet• Low noise preamplifier for mobile communication (PCN, DECT, GSM) in 2. ..
CGY60 ,GaAs MMIC (Low noise preamplifier for mobile communication PCN, DECT, GSM in 2.7V to 6V systems)Characteristics Symbol Limit Values Unitmin. typ. max.Drain current I – 69 mADPower Gain G dBV = 3 ..
CGY62 ,GaAs MMIC (Two-stage microwave broadband amplifier IC 50 ヘ input / output) GaAs MMIC CGY 62______________________________________________________________________ ..
CGY62 E6327 ,Broadband MMIC AmplifierCharacteristics Symbol min typ max UnitDrain current I - 130 175 mADPower Gain G dBf = 200 MHz to 1 ..
CH035H-40PT , SCHOTTKY BARRIER RECTIFIER VOLTAGE RANGE 20 - 40 Volts CURRENT 350 mAmperes
CMM6004-SC-0G00 , 0.25-3.0 GHz High Dynamic Range Amplifier
CMMSH1-100 , LM3402/LM3402HV 0.5A Constant Current Buck Regulator for Driving High Power LEDs
CMMSH1-100 , LM3402/LM3402HV 0.5A Constant Current Buck Regulator for Driving High Power LEDs
CMOZ18V , SURFACE MOUNT SILICON ZENER DIODE 2.4 VOLTS THRU 43 VOLTS 5% TOLERANCE
CMP04BY/883C ,Quad Low Power, Precision ComparatorSpecifications subject to change without notice.1ABSOLUTE MAXIMUM RATINGS 2Package Type u u UnitsJA ..
CMP04FP ,Quad Low Power, Precision ComparatorCHARACTERISTICS CMP04FP/FS, unless otherwise noted)1 CMP04B/FParameter Symbol Condit ..
CGY50
Broadband MMIC Amplifier
GaAs MMIC
CGY 50
____D a t a s h e e t
TypeMarkingOrdering code
(tape and reel)
Circuit diagram
Pin Configuration
Package 1)
Note: exceeding any of the max. ratings may cause permanent damage to the device. Appropriate handling isrequired to protect the electrostatic sensitive MMIC against degradation due to excess current spikes. Proper
ground connection of leads 1 and 3 ( with minimum inductance ) is required to achieve the guaranteed RF
performance, stable operating conditions and adequate tuning.Dimensions see chapter Package OutlinesSee application circuit.TS is measured on the source 1 lead at the soldering point to the PCB.
GaAs MMIC
CGY 50
____
Electrical characteristicsA = 25 °C, VG = 0 V, VD = 4.5 V, RS = RL = 50 Ω, unless otherwise specified
( for application circuit see next page )
Unit
GaAs MMICCGY 50
____
Application Circuit ( f = 800 to 1800 MHz )
50 Ohm Microstripline
Input
50Ohm
Output
50OhmDGL2C41
Legend of components
Note: Operating conditions for PIN, max : RG = RL = 50 Ω, C1, max = 220 pF,
VD = 4.5 V, VG current limited < 2 mA.
GaAs MMICCGY 50
____
Total Power Dissipation Ptot = f (TS;TA) 0 50 100
totP;[ °C ]
[ mW ]
500
GaAs MMICCGY 50
____
Typical Common Source S-ParametersG = 0V VD = 4.5 V Z0 = 50 Ω
:
www.ic-phoenix.com
.
