CBT3306PW ,CBT3306; Dual bus switchLOGIC DIAGRAM (positive logic) FUNCTION TABLEINPUT2 3 FUNCTION FUNCTION1A 1BOEL A port = B port11OE ..
CBT3384 ,10-bit bus switch with 5-bit output enables and Schottky undershoot protection
CBT3384D ,CBT3384; 10-bit bus switch with 5-bit output enablesINTEGRATED CIRCUITSCBT338410-bit bus switch with 5-bit output enablesProduct data2001 Dec 20Superse ..
CBT3384DB ,10-bit bus switch with 5-bit output enablesINTEGRATED CIRCUITSCBT338410-bit bus switch with 5-bit output enablesProduct data2001 Dec 20Superse ..
CBT3384DK ,10-bit bus switch with 5-bit output enablesINTEGRATED CIRCUITSCBT338410-bit bus switch with 5-bit output enablesProduct data2001 Dec 20Superse ..
CBT3384PW ,10-bit bus switch with 5-bit output enablesLogic diagram5. Pinning information5.1 PinningCBT3384 CBT33841OE 1 24 V 1OE 1 24 VCC CC1B1 2 23 2B5 ..
CDCV857BIDGG ,2.5 V Phase Lock Loop DDR Clock Driverblock diagram3Y02Y05Y137PWRDWN6Power DownY116AVDD and Test10Y2Logic9Y220Y319Y322Y423Y446Y547Y513CLK ..
CDCV857BIDGGR ,2.5 V Phase Lock Loop DDR Clock Drivermaximum ratings over operating free-air temperature (unless otherwise noted)Supply voltage range, V ..
CDCVF111FN ,1:9 Differential LVPECL Clock Drivermaximum ratings” may cause permanent damage to the device. These are stress ratings only, andfuncti ..
CDCVF111FN ,1:9 Differential LVPECL Clock Drivermaximum ratings over operating free-air temperature range (unless otherwise noted)Supply voltage ra ..
CDCVF2310PW ,High Performance 1:10 Clock Buffer for General Purpose ApplicationsFeatures 3 DescriptionThe CDCVF2310 device is a high-performance, low-1• High-Performance 1:10 Cloc ..
CDCVF2310PWG4 ,High Performance 1:10 Clock Buffer for General Purpose Applications 24-TSSOP -40 to 856.2 ESD RatingsVALUE UNIT(1)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001 2000ElectrostaticV V ..
CBT3306PW
CBT3306; Dual bus switch
Product data
File under Integrated Circuits — ICL03
2001 Nov 08
Philips Semiconductors Product data
CBT3306Dual bus switch
FEATURES 5 Ω switch connection between two ports TTL-compatible input levels Package options include plastic small outline (SO) and
thin shrink small outline (TSSOP) Latch-up protection exceeds 100 mA per JESD78 ESD protection exceeds 2000 V HBM per JESD22-A114 and
1000 V CDM per JESD22-C101
DESCRIPTIONThe CBT3306 Dual FET Bus Switch features independent line
switches. Each switch is disabled with the associated Output Enable
(OE) input is high.
The CBT3306 is characterized for operation from –40 to +85 °C.
PIN CONFIGURATION
PIN DESCRIPTION
QUICK REFERENCE DATA
ORDERING INFORMATIONStandard packing quantities and other packaging data is available at www.philipslogic.com/packaging.
LOGIC DIAGRAM (positive logic)
FUNCTION TABLE
Philips Semiconductors Product data
CBT3306Dual bus switch
ABSOLUTE MAXIMUM RATINGS1Tamb = –40 to +85 °C, unless otherwise specified.
NOTES: Stresses beyond those listed may cause permanent damage to the device. These are stress ratings only and functional operation of the
device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to
absolute-maximum-rated conditions for extended periods may affect device reliability. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. The package thermal impedance is calculated in accordance with JESD 51.
RECOMMENDED OPERATING CONDITIONS1
NOTE: All unused control inputs of the device must be held at VCC or GND to ensure proper device operation.
DC ELECTRICAL CHARACTERISTICSTamb = –40 to +85 °C, unless otherwise specified.
NOTES: All typical values are at VCC = 5 V, Tamb = 25 °C. This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND Measured by the voltage drop between the A and the B terminals at the indicated current through the switch.
On-state resistance is determined by the lowest voltage of the two (A or B) terminals.
Philips Semiconductors Product data
CBT3306Dual bus switch
AC CHARACTERISTICSTamb = –40 to +85 °C; CL = 50 pF
NOTE: The propagation delay is the calculated RC time constant of the typical on-state resistance of the switch and the specified load capacitance,
when driven by an ideal voltage source (zero output impedance).
AC WAVEFORMSVM = 1.5 V, VIN = GND to 3.0 V
Waveform 1. Input to Output Propagation Delays
Waveform 2. 3-State Output Enable and Disable Times
NOTES: tPLZ and tPHZ are the same as tdis. tPZL and tPZH are the same as ten. tPLH and tPHL are the same as tpd.
TEST CIRCUIT AND WAVEFORMS
NOTES: All input pulses are supplied by generators having the following
characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns. The outputs are measured one at a time with one transition per
measurement.
Philips Semiconductors Product data
CBT3306Dual bus switch
TSSOP8: plastic thin shrink small outline; 8 leads; body width 4.4 mm SOT530-1
Philips Semiconductors Product data
CBT3306Dual bus switch
SO8: plastic small outline package; 8 leads; body width 3.9 mm SOT96-1
