BTS724G ,Smart High Side SwitchesApplications • µC compatible high-side power switch with diagnostic feedback for 12V and 24V ground ..
BTS725L1 ,2 Channel PROFET Smart High Side Powe...General DescriptionN channel vertical power FET with charge pump, ground referenced CMOS compatible ..
BTS728L2 ,Smart High-Side Power Switch Two Channels: 2 x 60m Status FeedbackBlock Diagram • Short circuit protection Vbb• Overload protection • Current limitation • Thermal s ..
BTS730 ,Smart High Side Switches
BTS730 ,Smart High Side Switches
BTS730 ,Smart High Side Switches
BZX84C9V1L ,Small Signal +5% 9.1VElectrical Characteristics table on page 3 ofthis data sheet. Semiconductor Components Industries, ..
BZX84C9V1LT1 ,SEMICONDUCTOR(TECHNICAL DATA)Features• Pb−Free Packages are Available• 225 mW Rating on FR−4 or FR−5 Board3• Zener Breakdown Vol ..
BZX84C9V1LT3 ,Small Signal +5% 9.1Vmount plastic SOT−23 package. These devices are designed to providevoltage regulation with minimum ..
BZX84C9V1W-7-F , 200mW SURFACE MOUNT ZENER DIODE
BZX84J-B47 ,Single Zener diodesFeatures and benefits Total power dissipation: 250 mW Working voltage range: nominal 2.4 V to ..
BZX84J-B5V1 ,Single Zener diodes BZX84 seriesVoltage regulator diodesRev. 6 — 6 March 2014 Product data sheet1. Product profile1.1
BTS724G
Smart High Side Switches
BTS 724G
Smart High-Side Power Switch
Four Channels: 4 x 90mΩ
Status Feedback
Product Summary Package
General Description N channel vertical power MOSFET with charge pump, ground referenced CMOS compatible input and
diagnostic feedback, monolithically integrated in Smart SIPMOS technology. Providing embedded protective functions
Applications µC compatible high-side power switch with diagnostic feedback for 12V and 24V grounded loads All types of resistive, inductive and capacitve loads Most suitable for loads with high inrush currents, so as lamps Replaces electromechanical relays, fuses and discrete circuits
Basic Functions Very low standby current CMOS compatible input Improved electromagnetic compatibility (EMC) Fast demagnetization of inductive loads Stable behaviour at undervoltage Wide operating voltage range Logic ground independent from load ground
Protection Functions Block Diagram Short circuit protection Overload protection
• Current limitation
• Thermal shutdown Overvoltage protection (including load dump) with external
resistor Reverse battery protection with external resistor Loss of ground and loss of Vbb protection Electrostatic discharge protection (ESD)
Diagnostic Function Diagnostic feedback with open drain output Open load detection in OFF-state Feedback of thermal shutdown in ON-state
BTS 724G
Functional diagram BTS 724G
Pin Definitions and Functions
Pin configuration BTS 724G
Maximum Ratings at Tj = 25°C unless otherwise specified Supply voltages higher than Vbb(AZ) require an external current limit for the GND and status pins (a 150Ω
resistor for the GND connection is recommended.
2) RI = internal resistance of the load dump test pulse generator
3) VLoad dump is setup without the DUT connected to the generator per ISO 7637-1 and DIN 40839 Device on 50mm*50mm*1.5mm epoxy PCB FR4 with 6cm2 (one layer, 70µm thick) copper area for Vbb
BTS 724G
Thermal Characteristics
Electrical Characteristics
Load Switching Capabilities and Characteristics Device on 50mm*50mm*1.5mm epoxy PCB FR4 with 6cm2 (one layer, 70µm thick) copper area for Vbb
connection. PCB is vertical without blown air. See page 14 Soldering point: upper side of solder edge of device pin 15. See page 14
BTS 724G
Operating Parameters
Protection Functions15) 10) is the voltage, where the device doesn´t change it´s switching condition for 15ms after the supply voltage
falling below the lower limit of Vbb(on)
11) not subject to production test, specified by design
12) Supply voltages higher than Vbb(AZ) require an external current limit for the GND and status pins (a 150Ω
resistor for the GND connection is recommended). See also VON(CL) in table of protection functions and
circuit diagram on page 9.
13) Measured with load; for the whole device; all channels off
14) Add IST, if IST > 0
15) Integrated protection functions are designed to prevent IC destruction under fault conditions described in the
data sheet. Fault conditions are considered as "outside" normal operating range. Protection functions are not
designed for continuous repetitive operation.
BTS 724G
Reverse Battery
Diagnostic Characteristics
Input and Status Feedback18) 17) Requires a 150 Ω resistor in GND connection. The reverse load current through the intrinsic drain-source
diode has to be limited by the connected load. Power dissipation is higher compared to normal operating
conditions due to the voltage drop across the drain-source diode. The temperature protection is not active
during reverse current operation! Input and Status currents have to be limited (see max. ratings page 4 and
circuit page 9).