ADSP2189MBST-266 ,DSP MicrocomputerOVERVIEWdevelopment. The Assembler has an algebraic syntax that is easyThe ADSP-2189M instruction s ..
ADSP-2189MBSTZ-266 , DSP Microcomputer
ADSP2189MKST300 ,DSP MicrocomputerFEATURES FUNCTIONAL BLOCK DIAGRAMPERFORMANCEPOWER-DOWNCONTROL13.3 ns Instruction Cycle Time @ 2.5 V ..
ADSP-2189MKST-300 ,DSP Microcomputerspecifications of the EZ-ICE target• Receive and transmit data through the two serial portsboard co ..
ADSP-2189NBST-320 ,DSP MicrocomputerFEATURES Memory Space Permits “Glueless” System DesignADSP-2100 Family Code Compatible (Easy to Use ..
ADSP-2189NKST-320 ,DSP MicrocomputerFEATURESSingle-Cycle Context Switch Flexible I/O Allows 1.8 V, 2.5 V or 3.3 V Operation3-Bus Archit ..
AM26C31CD ,Quadruple Differential Line DriverFeatures section and added the Applications section, the Device Information table, ESD Ratings tabl ..
AM26C31CDB , QUADRUPLE DIFFERENTIAL LINE DRIVERS
AM26C31CDBR ,Quadruple Differential Line DriverElectrical Characteristics: AM26C31Q and12 Device and Documentation Support........ 15AM26C31M. 612 ..
AM26C31CDBRG4 ,Quadruple Differential Line Driver 16-SSOP 0 to 70Features 3 DescriptionThe AM26C31 device is a differential line driver with1• Meets or Exceeds the ..
AM26C31CDG4 ,Quadruple Differential Line Driver 16-SOIC 0 to 70Block Diagrams. 103 Description....... 18.3 Feature Description.... 114 Revision History........ 28 ..
AM26C31CDR ,Quadruple Differential Line DriverMaximum Ratings . 49.2 Typical Application .... 126.2 ESD Ratings........ 410 Power Supply Recommen ..
ADSP-2189MBST-266-ADSP2189MBST-266-ADSP2189MKST300-ADSP-2189MKST-300
DSP Microcomputer
REV. A
DSP Microcomputer
FUNCTIONAL BLOCK DIAGRAM
GENERAL DESCRIPTIONThe ADSP-2189M is a single-chip microcomputer optimized
for digital signal processing (DSP) and other high speed nu-
meric processing applications.
The ADSP-2189M combines the ADSP-2100 family base archi-
tecture (three computational units, data address generators and
a program sequencer) with two serial ports, a 16-bit internal
DMA port, a byte DMA port, a programmable timer, Flag I/O,
extensive interrupt capabilities, and on-chip program and data
memory.
The ADSP-2189M integrates 192K bytes of on-chip memory
configured as 32K words (24-bit) of program RAM and 48K
words (16-bit) of data RAM. Power-down circuitry is also pro-
vided to meet the low power needs of battery operated portable
equipment. The ADSP-2189M is available in a 100-lead LQFP
package.
In addition, the ADSP-2189M supports new instructions, which
include bit manipulations—bit set, bit clear, bit toggle, bit test—
new ALU constants, new multiplication instruction (x squared),
biased rounding, result free ALU operations, I/O memory trans-
fers and global interrupt masking, for increased flexibility.
FEATURES
PERFORMANCE
13.3 ns Instruction Cycle Time @ 2.5 Volts (Internal),MIPS Sustained Performance
Single-Cycle Instruction Execution
Single-Cycle Context Switch
3-Bus Architecture Allows Dual Operand Fetches in
Every Instruction Cycle
Multifunction Instructions
Power-Down Mode Featuring Low CMOS Standby
Power Dissipation with 200 CLKIN Cycle Recovery
from Power-Down Condition
Low Power Dissipation in Idle Mode
INTEGRATION
ADSP-2100 Family Code Compatible (Easy to Use Alge-
braic Syntax), with Instruction Set Extensions
192K Bytes of On-Chip RAM, Configured as 32K Words
On-Chip Program Memory RAM and 48K Words On-
Chip Data Memory RAM
Dual Purpose Program Memory for Both Instruction
and Data Storage
Independent ALU, Multiplier/Accumulator and Barrel
Shifter Computational Units
Two Independent Data Address Generators
Powerful Program Sequencer Provides Zero Overhead
Looping Conditional Instruction Execution
Programmable 16-Bit Interval Timer with Prescaler
100-Lead LQFP
SYSTEM INTERFACE
Flexible I/O Structure Allows 2.5 V or 3.3 V Operation;
All Inputs Tolerate Up to 3.6 V, Regardless of Mode
16-Bit Internal DMA Port for High Speed Access to On-
Chip Memory (Mode Selectable)
4 MByte Memory Interface for Storage of Data Tables
and Program Overlays (Mode Selectable)
8-Bit DMA to Byte Memory for Transparent Program
and Data Memory Transfers (Mode Selectable)
I/O Memory Interface with 2048 Locations Supports
Parallel Peripherals (Mode Selectable)
Programmable Memory Strobe and Separate I/O
Memory Space Permits “Glueless” System Design
Programmable Wait-State Generation
Two Double-Buffered Serial Ports with Companding
Hardware and Automatic Data Buffering
Automatic Booting of On-Chip Program Memory from
Byte-Wide External Memory, e.g., EPROM, or
Through Internal DMA Port
Six External Interrupts
13 Programmable Flag Pins Provide Flexible System
Signaling
UART Emulation through Software SPORT Reconfiguration
ICE-Port™ Emulator Interface Supports Debugging in
Final SystemsICE-Port is a trademark of Analog Devices, Inc.
ADSP-2189MFabricated in a high speed, low power, CMOS process, the
ADSP-2189M operates with a 13.3 ns instruction cycle time.
Every instruction can execute in a single processor cycle.
The ADSP-2189M’s flexible architecture and comprehensive
instruction set allow the processor to perform multiple opera-
tions in parallel. In one processor cycle, the ADSP-2189M can:Generate the next program addressFetch the next instructionPerform one or two data movesUpdate one or two data address pointersPerform a computational operation
This takes place while the processor continues to:Receive and transmit data through the two serial portsReceive and/or transmit data through the internal DMA portReceive and/or transmit data through the byte DMA portDecrement timer
DEVELOPMENT SYSTEMThe ADSP-2100 Family Development Software, a complete set
of tools for software and hardware system development, sup-
ports the ADSP-2189M. The System Builder provides a high
level method for defining the architecture of systems under
development. The Assembler has an algebraic syntax that is easy
to program and debug. The Linker combines object files into an
executable file. The Simulator provides an interactive instruc-
tion-level simulation with a reconfigurable user interface to
display different portions of the hardware environment.
A PROM Splitter generates PROM programmer compatible
files. The C Compiler, based on the Free Software Foundation’s
GNU C Compiler, generates ADSP-2189M assembly source
code. The source code debugger allows programs to be cor-
rected in the C environment. The Runtime Library includes over
100 ANSI-standard mathematical and DSP-specific functions.
The EZ-KIT Lite is a hardware/software kit offering a complete
development environment for the entire ADSP-21xx family: an
ADSP-218x-based evaluation board with PC monitor software
plus Assembler, Linker, Simulator and PROM Splitter software.
The ADSP-218x EZ-KIT Lite is a low cost, easy to use hard-
ware platform on which you can quickly get started with your
DSP software design. The EZ-KIT Lite includes the following
features:33 MHz ADSP-218xFull 16-bit Stereo Audio I/O with AD1847 SoundPort®
CodecRS-232 Interface to PC with Windows 3.1 Control SoftwareEZ-ICE Connector for Emulator ControlDSP Demo Programs
The ADSP-218x EZ-ICE® Emulator aids in the hardware de-
bugging of an ADSP-2189M system. The emulator consists of
hardware, host computer resident software and the target board
connector. The ADSP-2189M integrates on-chip emulation
support with a 14-pin ICE-Port interface. This interface pro-
vides a simpler target board connection that requires fewer
mechanical clearance considerations than other ADSP-2100
Family EZ-ICEs. The ADSP-2189M device need not be re-
The EZ-ICE performs a full range of functions, including:In-target operationUp to 20 breakpointsSingle-step or full-speed operationRegisters and memory values can be examined and alteredPC upload and download functionsInstruction-level emulation of program booting and executionComplete assembly and disassembly of instructionsC source-level debugging
See “Designing An EZ-ICE-Compatible Target System” in the
ADSP-2100 Family EZ-Tools Manual (ADSP-2181 sections) as
well as the Designing an EZ-ICE compatible System section of
this data sheet for the exact specifications of the EZ-ICE target
board connector.
Additional InformationThis data sheet provides a general overview of ADSP-2189M
functionality. For additional information on the architecture and
instruction set of the processor, refer to the ADSP-2100 Family
User’s Manual, Third Edition. For more information about the
development tools, refer to the ADSP-2100 Family Develop-
ment Tools Data Sheet.
ARCHITECTURE OVERVIEWThe ADSP-2189M instruction set provides flexible data moves
and multifunction (one or two data moves with a computation)
instructions. Every instruction can be executed in a single pro-
cessor cycle. The ADSP-2189M assembly language uses an
algebraic syntax for ease of coding and readability. A compre-
hensive set of development tools supports program development.
Figure 1.Functional Block Diagram
Figure 1 is an overall block diagram of the ADSP-2189M. The
processor contains three independent computational units: the
ALU, the multiplier/accumulator (MAC) and the shifter. The
computational units process 16-bit data directly and have provi-
sions to support multiprecision computations. The ALU per-
forms a standard set of arithmetic and logic operations; division
primitives are also supported. The MAC performs single-cycle
multiply, multiply/add and multiply/subtract operations with 40
bits of accumulation. The shifter performs logical and arith-
metic shifts, normalization, denormalization and derive expo-
nent operations.
The internal result (R) bus connects the computational units so
that the output of any unit may be the input of any unit on the
next cycle.
A powerful program sequencer and two dedicated data address
generators ensure efficient delivery of operands to these compu-
tational units. The sequencer supports conditional jumps, sub-
routine calls and returns in a single cycle. With internal loop
counters and loop stacks, the ADSP-2189M executes looped
code with zero overhead; no explicit jump instructions are re-
quired to maintain loops.
Two data address generators (DAGs) provide addresses for
simultaneous dual operand fetches (from data memory and
program memory). Each DAG maintains and updates four
address pointers. Whenever the pointer is used to access data
(indirect addressing), it is post-modified by the value of one of
four possible modify registers. A length value may be associated
with each pointer to implement automatic modulo addressing
for circular buffers.
Efficient data transfer is achieved with the use of five internal
buses:Program Memory Address (PMA) BusProgram Memory Data (PMD) BusData Memory Address (DMA) BusData Memory Data (DMD) BusResult (R) Bus
The two address buses (PMA and DMA) share a single external
address bus, allowing memory to be expanded off-chip and the
two data buses (PMD and DMD) share a single external data
bus. Byte memory space and I/O memory space also share the
external buses.
Program memory can store both instructions and data, permit-
ting the ADSP-2189M to fetch two operands in a single cycle,
one from program memory and one from data memory. The
ADSP-2189M can fetch an operand from program memory and
the next instruction in the same cycle.
In lieu of the address and data bus for external memory connec-
tion, the ADSP-2189M may be configured for 16-bit Internal
DMA port (IDMA port) connection to external systems. The
IDMA port is made up of 16 data/address pins and five control
pins. The IDMA port provides transparent, direct access to the
DSPs on-chip program and data RAM.
An interface to low cost byte-wide memory is provided by the
Byte DMA port (BDMA port). The BDMA port is bidirectional
and can directly address up to four megabytes of external RAM
or ROM for off-chip storage of program overlays or data tables.
The byte memory and I/O memory space interface supports
slow memories and I/O memory-mapped peripherals with pro-
grammable wait-state generation. External devices can gain
control of external buses with bus request/grant signals (BR,
BGH and BG). One execution mode (Go Mode) allows the
ADSP-2189M to continue running from on-chip memory.
Normal execution mode requires the processor to halt while
buses are granted.
The ADSP-2189M can respond to eleven interrupts. There can
RESET signal. The two serial ports provide a complete synchro-
nous serial interface with optional companding in hardware and
a wide variety of framed or frameless data transmit and receive
modes of operation.
Each port can generate an internal programmable serial clock or
accept an external serial clock.
The ADSP-2189M provides up to 13 general-purpose flag pins.
The data input and output pins on SPORT1 can be alternatively
configured as an input flag and an output flag. In addition, eight
flags are programmable as inputs or outputs and three flags are
always outputs.
A programmable interval timer generates periodic interrupts. A
16-bit count register (TCOUNT) decrements every n processor
cycles, where n is a scaling value stored in an 8-bit register
(TSCALE). When the value of the count register reaches zero,
an interrupt is generated and the count register is reloaded from
a 16-bit period register (TPERIOD).
Serial PortsThe ADSP-2189M incorporates two complete synchronous
serial ports (SPORT0 and SPORT1) for serial communications
and multiprocessor communication.
Here is a brief list of the capabilities of the ADSP-2189M
SPORTs. For additional information on Serial Ports, refer to
the ADSP-2100 Family User’s Manual, Third Edition.SPORTs are bidirectional and have a separate, double-buff-
ered transmit and receive section.SPORTs can use an external serial clock or generate their
own serial clock internally.SPORTs have independent framing for the receive and trans-
mit sections. Sections run in a frameless mode or with frame
synchronization signals internally or externally generated.
Frame sync signals are active high or inverted, with either of
two pulsewidths and timings.SPORTs support serial data word lengths from 3 to 16 bits
and provide optional A-law and µ-law companding according
to CCITT recommendation G.711.SPORT receive and transmit sections can generate unique
interrupts on completing a data word transfer.SPORTs can receive and transmit an entire circular buffer of
data with only one overhead cycle per data word. An interrupt
is generated after a data buffer transfer.SPORT0 has a multichannel interface to selectively receive
and transmit a 24- or 32-word, time-division multiplexed,
serial bitstream.SPORT1 can be configured to have two external interrupts
(IRQ0 and IRQ1) and the Flag In and Flag Out signals. The
internally generated serial clock may still be used in this con-
figuration.
PIN DESCRIPTIONSThe ADSP-2189M will be available in a 100-lead LQFP pack-
age. In order to maintain maximum functionality and reduce
package size and pin count, some serial port, programmable
ADSP-2189Mfunctionality is reconfigurable, the default state is shown in plain
text; alternate functionality is shown in italics.
Common-Mode PinsNOTES
1Interrupt/Flag Pins retain both functions concurrently. If IMASK is set to
enable the corresponding interrupts, then the DSP will vector to the appropri-
ate interrupt vector address when the pin is asserted, either by external devices,
or set as a programmable flag.
2SPORT configuration determined by the DSP System Control Register. Soft-
ware configurable.
Memory Interface PinsThe ADSP-2189M processor can be used in one of two modes,
Full Memory Mode, which allows BDMA operation with full
external overlay memory and I/O capability, or Host Mode,
which allows IDMA operation with limited external addressing
capabilities. The operating mode is determined by the state of
the Mode C pin during RESET and cannot be changed while
the processor is running.
Full Memory Mode Pins (Mode C = 0)
Host Mode Pins (Mode C = 1)NOTEIn Host Mode, external peripheral addresses can be decoded using the A0,
CMS, PMS, DMS and IOMS signals.
InterruptsThe interrupt controller allows the processor to respond to the
eleven possible interrupts and reset with minimum overhead.
The ADSP-2189M provides four dedicated external interrupt
input pins, IRQ2, IRQL0, IRQL1 and IRQE (shared with the
PF7:4 pins). In addition, SPORT1 may be reconfigured for
IRQ0, IRQ1, FLAG_IN and FLAG_OUT, for a total of six
external interrupts. The ADSP-2189M also supports internal
interrupts from the timer, the byte DMA port, the two serial
ports, software and the power-down control circuit. The inter-
rupt levels are internally prioritized and individually maskable
(except power-down and reset). The IRQ2, IRQ0 and IRQ1
input pins can be programmed to be either level- or edge-sensi-
tive. IRQL0 and IRQL1 are level-sensitive and IRQE is edge-
sensitive. The priorities and vector addresses of all interrupts are
shown in Table I.
Table I.Interrupt Priority and Interrupt Vector AddressesPower-Down (Nonmaskable)
IRQ2
IRQL1
IRQL0
SPORT0 Transmit
SPORT0 Receive
IRQE
BDMA Interrupt
SPORT1 Transmit or IRQ1
SPORT1 Receive or IRQ0
Interrupt routines can either be nested with higher priority
interrupts taking precedence or processed sequentially. Inter-
rupts can be masked or unmasked with the IMASK register.
Individual interrupt requests are logically ANDed with the bits
in IMASK; the highest priority unmasked interrupt is then
selected. The power-down interrupt is nonmaskable.
The ADSP-2189M masks all interrupts for one instruction cycle
following the execution of an instruction that modifies the IMASK
register. This does not affect serial port autobuffering or DMA
transfers.
The interrupt control register, ICNTL, controls interrupt nest-
ing and defines the IRQ0, IRQ1 and IRQ2 external interrupts to
be either edge- or level-sensitive. The IRQE pin is an external
edge-sensitive interrupt and can be forced and cleared. The
IRQL0 and IRQL1 pins are external level-sensitive interrupts.
The IFC register is a write-only register used to force and clear
interrupts. On-chip stacks preserve the processor status and are
automatically maintained during interrupt handling. The stacks
are twelve levels deep to allow interrupt, loop and subroutine
nesting. The following instructions allow global enable or dis-
able servicing of the interrupts (including power-down), regard-
less of the state of IMASK. Disabling the interrupts does not
affect serial port autobuffering or DMA.
ENA INTS;
DIS INTS;
When the processor is reset, interrupt servicing is enabled.
LOW POWER OPERATIONThe ADSP-2189M has three low power modes that significantly
reduce the power dissipation when the device operates under
standby conditions. These modes are:Power-DownIdleSlow Idle
The CLKOUT pin may also be disabled to reduce external
power dissipation.
Power-DownThe ADSP-2189M processor has a low power feature that lets
Third Edition, “System Interface” chapter, for detailed infor-
mation about the power-down feature.Quick recovery from power-down. The processor begins
executing instructions in as few as 200 CLKIN cycles.Support for an externally generated TTL or CMOS proces-
sor clock. The external clock can continue running during
power-down without affecting the lowest power rating and
200 CLKIN cycle recovery.Support for crystal operation includes disabling the oscillator
to save power (the processor automatically waits approxi-
mately 4096 CLKIN cycles for the crystal oscillator to start
or stabilize) and letting the oscillator run to allow 200 CLKIN
cycle start up.Power-down is initiated by either the power-down pin
(PWD) or the software power-down force bit. Interrupt
support allows an unlimited number of instructions to be
executed before optionally powering down. The power-down
interrupt also can be used as a nonmaskable, edge-sensitive
interrupt.Context clear/save control allows the processor to continue
where it left off or start with a clean context when leaving the
power-down state.The RESET pin also can be used to terminate power-down.Power-down acknowledge pin indicates when the processor
has entered power-down.
IdleWhen the ADSP-2189M is in the Idle Mode, the processor
waits indefinitely in a low power state until an interrupt occurs.
When an unmasked interrupt occurs, it is serviced; execution
then continues with the instruction following the IDLE instruc-
tion. In Idle mode IDMA, BDMA and autobuffer cycle steals
still occur.
Slow IdleThe IDLE instruction is enhanced on the ADSP-2189M to let
the processor’s internal clock signal be slowed, further reducing
power consumption. The reduced clock frequency, a program-
mable fraction of the normal clock rate, is specified by a select-
able divisor given in the IDLE instruction.
The format of the instruction is:
IDLE (n);
where n = 16, 32, 64 or 128. This instruction keeps the proces-
sor fully functional, but operating at the slower clock rate. While
it is in this state, the processor’s other internal clock signals,
such as SCLK, CLKOUT and timer clock, are reduced by the
same ratio. The default form of the instruction, when no clock
divisor is given, is the standard IDLE instruction.
When the IDLE (n) instruction is used, it effectively slows down
the processor’s internal clock and thus its response time to in-
coming interrupts. The one-cycle response time of the standard
idle state is increased by n, the clock divisor. When an enabled
interrupt is received, the ADSP-2189M will remain in the idle
state for up to a maximum of n processor cycles (n = 16, 32, 64,
or 128) before resuming normal operation.
ADSP-2189Mfaster rate than can be serviced, due to the additional time the
processor takes to come out of the idle state (a maximum of n
processor cycles).
SYSTEM INTERFACEFigure 2 shows typical basic system configurations with the
ADSP-2189M, two serial devices, a byte-wide EPROM and
optional external program and data overlay memories (mode
selectable). Programmable Wait-State generation allows the
processor connects easily to slow peripheral devices. The
ADSP-2189M also provides four external interrupts and two
serial ports or six external interrupts and one serial port. Host
Memory Mode allows access to the full external data bus, but
limits addressing to a single address bit (A0). Additional system
peripherals can be added in this mode through the use of exter-
nal hardware to generate and latch address signals.
Clock SignalsThe ADSP-2189M can be clocked by either a crystal or a TTL-
compatible clock signal.
The CLKIN input cannot be halted, changed during operation,
or operated below the specified frequency during normal opera-
tion. The only exception is while the processor is in the power-
down state. For additional information, refer to Chapter 9,
ADSP-2100 Family User’s Manual, Third Edition for detailed
information on this power-down feature.
If an external clock is used, it should be a TTL-compatible
signal running at half the instruction rate. The signal is con-
nected to the processor’s CLKIN input. When an external clock
is used, the XTAL input must be left unconnected.
The ADSP-2189M uses an input clock with a frequency equal
to half the instruction rate; a 37.50 MHz input clock yields a
13.3ns processor cycle (which is equivalent to 75 MHz). Nor-
mally, instructions are executed in a single processor cycle. All
device timing is relative to the internal instruction clock rate,
which is indicated by the CLKOUT signal when enabled.
Because the ADSP-2189M includes an on-chip oscillator cir-
cuit, an external crystal may be used. The crystal should be
connected across the CLKIN and XTAL pins, with two capaci-
tors connected as shown in Figure 3. Capacitor values are de-
pendent on crystal type and should be specified by the crystal
manufacturer. A parallel-resonant, fundamental frequency,
microprocessor-grade crystal should be used.
A clock output (CLKOUT) signal is generated by the processor
at the processor’s cycle rate. This can be enabled and disabled
by the CLKODIS bit in the SPORT0 Autobuffer Control
Register.
Figure 3.External Crystal Connections
ResetThe RESET signal initiates a master reset of the ADSP-2189M.
The RESET signal must be asserted during the power-up se-
quence to assure proper initialization. RESET during initial
power-up must be held long enough to allow the internal clock
to stabilize. If RESET is activated any time after power-up, the
clock continues to run and does not require stabilization time.
The power-up sequence is defined as the total time required for
the crystal oscillator circuit to stabilize after a valid VDD is ap-
plied to the processor and for the internal phase-locked loop
(PLL) to lock onto the specific crystal frequency. A minimum of
2000 CLKIN cycles ensures that the PLL has locked but does
not include the crystal oscillator start-up time. During this
power-up sequence the RESET signal should be held low. On
any subsequent resets, the RESET signal must meet the mini-
mum pulsewidth specification, tRSP.
The master reset sets all internal stack pointers to the empty
stack condition, masks all interrupts and clears the MSTAT
register. When RESET is released, if there is no pending bus
request and the chip is configured for booting, the boot-loading
sequence is performed. The first instruction is fetched from
on-chip program memory location 0x0000 once boot loading
completes.
Power SuppliesThe ADSP-2189M has separate power supply connections for
the internal (VDDINT) and external (VDDEXT) power supplies.
The internal supply must meet the 2.5 V requirement. The
external supply can be connected to either a 2.5 V or 3.3 V
supply. All external supply pins must be connected to the same
supply. All input and I/O pins can tolerate input voltages up
to 3.6V regardless of the external supply voltage. This fea-
ture provides maximum flexibility in mixing 2.5V and 3.3V
components.
MODES OF OPERATION
Setting Memory ModeMemory Mode selection for the ADSP-2189M is made during
chip reset through the use of the Mode C pin. This pin is multi-
plexed with the DSP’s PF2 pin, so care must be taken in how
the mode selection is made. The two methods for selecting the
value of Mode C are active and passive.
Table II.ADSP-2189M Modes of OperationNOTE
1Considered as standard operating settings. Using these configurations allows for easier design and better memory management.
Passive Configuration involves the use a pull-up or pull-downresistor connected to the Mode C pin. To minimize power
consumption, or if the PF2 pin is to be used as an output in the
DSP application, a weak pull-up or pull-down, on the order of
10 kΩ, can be used. This value should be sufficient to pull the
pin to the desired level and still allow the pin to operate as a
programmable flag output without undue strain on the processor’s
output driver. For minimum power consumption during power-
down, reconfigure PF2 to be an input, as the pull-up or pull-
down will hold the pin in a known state and will not switch.
Active Configuration involves the use of a three-statable ex-ternal driver connected to the Mode C pin. A driver’s output
enable should be connected to the DSP’s RESET signal such
that it only drives the PF2 pin when RESET is active (low).
When RESET is deasserted, the driver should three-state, thus
allowing full use of the PF2 pin as either an input or output. To
minimize power consumption during power-down, configure
the programmable flag as an output when connected to a three-
stated buffer. This ensures that the pin will be held at a constant
level and will not oscillate should the three-state driver’s level
hover around the logic switching point.
IACK ConfigurationMode D = 0 and in host mode: IACK is an active, driven signal
and cannot be wire OR-ed.
ADSP-2189MMode D = 1 and in host mode: IACK is an open source and
requires an external pull-down, but multiple IACK pins can be
wire OR-ed together.
MEMORY ARCHITECTUREThe ADSP-2189M provides a variety of memory and peripheral
interface options. The key functional groups are Program Memory,
Data Memory, Byte Memory and I/O. Refer to the following
figures and tables for PM and DM memory allocations in the
ADSP-2189M.
Program Memory
Program Memory, Full Memory Mode is a 24-bit-wide spacefor storing both instruction op codes and data. The ADSP-2189M
has 32K words of Program Memory RAM on chip and the
capability of accessing up to two 8K external memory overlay
spaces using the external data bus.
Program Memory, Host Mode allows access to all internalmemory. External overlay access is limited by a single external
address line (A0). External program execution is not available in
host mode due to a restricted data bus that is 16-bits wide only.
Table III.PMOVLAY Bits
Data Memory
Data Memory, Full Memory Mode is a 16-bit-wide spaceused for the storage of data variables and for memory-mapped
control registers. The ADSP-2189M has 48K words on Data
Memory RAM on-chip. Part of this space is used by 32 memory-
mapped registers. Support also exists for up to two 8K external
memory overlay spaces through the external data bus. All inter-
nal accesses complete in one cycle. Accesses to external memory
are timed using the wait-states specified by the DWAIT register
and the wait-state mode bit.
Figure 5.Data Memory Map
Figure 4.Program Memory
Data Memory, Host Mode allows access to all internalmemory. External overlay access is limited by a single external
address line (A0).
Table IV.DMOVLAY Bits
Memory Mapped Registers (New to the ADSP-2189M)The ADSP-2189M has three memory mapped registers that
differ from other ADSP-21xx Family DSPs. The slight modifi-
cations to these registers (Wait-State Control, Programmable
Flag and Composite Select Control and System Control) pro-
vide the ADSP-2189M’s wait-state and BMS control features.
Figure 6.Wait-State Control Register (ADSP-2189M)
BMWAIT
(BIT-15, ADSP-2189M)
CMSSEL
0 = DISABLE CMS
1 = ENABLE CMS
DM(0x3FE6)
PROGRAMMABLE FLAG & COMPOSITE SELECT CONTROL
PFTYPE
0 = INPUT
1 = OUTPUT
(WHERE BIT: 11-IOM, 10BM, 9-DM, 8-PM)14131211109876543210Figure 7.Programmable Flag and Composite Select Con-
trol Register
SPORT0 ENABLE
0 = DISABLE
1 = ENABLE
DM(0x3FFF)
SYSTEM CONTROL
SPORT1 CONFIGURE
0 = FI, FO, IRQ0, IRQ1, SCLK
1 = SPORT114131211109876543210Figure 8.System Control Register
I/O Space (Full Memory Mode)The ADSP-2189M supports an additional external memory
space called I/O space. This space is designed to support simple
connections to peripherals (such as data converters and external
registers) or to bus interface ASIC data registers. I/O space
supports 2048 locations of 16-bit-wide data. The lower eleven
bits of the external address bus are used; the upper three bits are
undefined. Two instructions were added to the core ADSP-2100
Family instruction set to read from and write to I/O memory
space. The I/O space also has four dedicated three-bit wait-state
registers, IOWAIT0–3, which, in combination with the wait-
state mode bit, specify up to 15 wait-states to be automatically
generated for each of four regions. The wait-states act on ad-
dress ranges as shown in Table V.
Table V.Wait-States
Composite Memory Select (CMS)The ADSP-2189M has a programmable memory select signal
that is useful for generating memory select signals for memories
mapped to more than one space. The CMS signal is generated
to have the same timing as each of the individual memory
select signals (PMS, DMS, BMS, IOMS) but can combine
their functionality.
When set, each bit in the CMSSEL register causes the CMS
signal to be asserted when the selected memory select is as-
serted. For example, to use a 32K word memory to act as both
program and data memory, set the PMS and DMS bits in the
CMSSEL register and use the CMS pin to drive the chip select
of the memory, and use either DMS or PMS as the additional
address bit.
The CMS pin functions like the other memory select signals,
with the same timing and bus request logic. A 1 in the enable bit
causes the assertion of the CMS signal at the same time as the
selected memory select signal. All enable bits default to 1 at
reset, except the BMS bit.
Byte Memory Select (BMS)The ADSP-2189M’s BMS disable feature combined with the
CMS pin lets you use multiple memories in the byte memory
space. For example, an EPROM could be attached to the BMS
select, and an SRAM could be connected to CMS. Because
BMS is enabled at reset, the EPROM would be used for boot-
ing. After booting, software could disable BMS and set the
CMS signal to respond to BMS, enabling the SRAM.
ADSP-2189M
Byte MemoryThe byte memory space is a bidirectional, 8-bit-wide, external
memory space used to store programs and data. Byte memory is
accessed using the BDMA feature. The byte memory space
consists of 256 pages, each of which is 16K × 8.
The byte memory space on the ADSP-2189M supports read
and write operations as well as four different data formats. The
byte memory uses data bits 15:8 for data. The byte memory
uses data bits 23:16 and address bits 13:0 to create a 22-bit
address. This allows up to a 4 meg × 8 (32 megabit) ROM or
RAM to be used without glue logic. All byte memory accesses
are timed by the BMWAIT register and the wait-state mode bit.
Byte Memory DMA (BDMA, Full Memory Mode)The Byte memory DMA controller allows loading and storing of
program instructions and data using the byte memory space.
The BDMA circuit is able to access the byte memory space
while the processor is operating normally and steals only one
DSP cycle per 8-, 16- or 24-bit word transferred.
Figure 9.BDMA Control Register
The BDMA circuit supports four different data formats which
are selected by the BTYPE register field. The appropriate num-
ber of 8-bit accesses are done from the byte memory space to
build the word size selected. Table VI shows the data formats
supported by the BDMA circuit.
Table VI.Data FormatsUnused bits in the 8-bit data memory formats are filled with 0s.
The BIAD register field is used to specify the starting address
for the on-chip memory involved with the transfer. The 14-bit
BEAD register specifies the starting address for the external byte
memory space. The 8-bit BMPAGE register specifies the start-
ing page for the external byte memory space. The BDIR register
field selects the direction of the transfer. Finally, the 14-bit
BWCOUNT register specifies the number of DSP words to
transfer and initiates the BDMA circuit transfers.
BDMA accesses can cross page boundaries during sequential
addressing. A BDMA interrupt is generated on the completion
of the number of transfers specified by the BWCOUNT register.
The BWCOUNT register is updated after each transfer so it can
be used to check the status of the transfers. When it reaches
zero, the transfers have finished and a BDMA interrupt is gener-
ated. The BMPAGE and BEAD registers must not be accessed
by the DSP during BDMA operations.
The source or destination of a BDMA transfer will always be
on-chip program or data memory.
When the BWCOUNT register is written with a nonzero value
the BDMA circuit starts executing byte memory accesses with
wait-states set by BMWAIT. These accesses continue until the
count reaches zero. When enough accesses have occurred to
create a destination word, it is transferred to or from on-chip
memory. The transfer takes one DSP cycle. DSP accesses to
external memory have priority over BDMA byte memory
accesses.
The BDMA Context Reset bit (BCR) controls whether the
processor is held off while the BDMA accesses are occurring.
Setting the BCR bit to 0 allows the processor to continue opera-
tions. Setting the BCR bit to 1 causes the processor to stop
execution while the BDMA accesses are occurring, to clear the
context of the processor, and start execution at address 0 when
the BDMA accesses have completed.
The BDMA overlay bits specify the OVLAY memory blocks to
be accessed for internal memory.
The BMWAIT field, which has four bits on ADSP-2189M,
allows selection of up to 15 wait-states for BDMA transfers.
Internal Memory DMA Port (IDMA Port; Host Memory
Mode)The IDMA Port provides an efficient means of communication
between a host system and the ADSP-2189M. The port is used
to access the on-chip program memory and data memory of the
DSP with only one DSP cycle per word overhead. The IDMA
port cannot, however, be used to write to the DSP’s memory-
mapped control registers. A typical IDMA transfer process is
described as follows:Host starts IDMA transfer.Host checks IACK control line to see if the DSP is busy.Host uses IS and IAL control lines to latch either the DMA
starting address (IDMAA) or the PM/DM OVLAY selection
into the DSP’s IDMA control registers. If Bit 15 = 1, the
value of bits 7:0 represent the IDMA overlay: Bits 14:8 must
be set to 0. If Bit 15 = 0, the value of bits 13:0 represent the
starting address of internal memory to be accessed and Bit 14
reflects PM or DM for access.Host uses IS and IRD (or IWR) to read (or write) DSP inter-
nal memory (PM or DM).Host checks IACK line to see if the DSP has completed the
previous IDMA operation.Host ends IDMA transfer.
The IDMA port has a 16-bit multiplexed address and data bus
and supports 24-bit program memory. The IDMA port is com-
pletely asynchronous and can be written while the ADSP-2189M
is operating at full speed.
The DSP memory address is latched and then automatically
incremented after each IDMA transaction. An external device
can therefore access a block of sequentially addressed memory
by specifying only the starting address of the block. This in-
creases throughput as the address does not have to be sent for
each memory access.
IDMA Port access occurs in two phases. The first is the IDMA
Address Latch cycle. When the acknowledge is asserted, a 14-bit
address and 1-bit destination type can be driven onto the bus by
an external device. The address specifies an on-chip memory
location, the destination type specifies whether it is a DM or
PM access. The falling edge of the IDMA address latch signal
(IAL) or the missing edge of the IDMA select signal (IS) latches
this value into the IDMAA register.
Once the address is stored, data can then be either read from, or
written to, the ADSP-2189M’s on-chip memory. Asserting the
select line (IS) and the appropriate read or write line (IRD and
IWR respectively) signals the ADSP-2189M that a particular
transaction is required. In either case, there is a one-processor-
cycle delay for synchronization. The memory access consumes
one additional processor cycle.
Once an access has occurred, the latched address is automati-
cally incremented and another access can occur.
Through the IDMAA register, the DSP can also specify the
starting address and data format for DMA operation. Asserting
the IDMA port select (IS) and address latch enable (IAL) di-
rects the ADSP-2189M to write the address onto the IAD0-14
bus into the IDMA Control Register. If Bit 15 is set to 0, IDMA
latches the address. If Bit 15 is set to 1, IDMA latches into the
OVLAY register. This register, shown below, is memory
mapped at address DM (0x3FE0). Note that the latched address
(IDMAA) cannot be read back by the host.
Refer to the following figures for more information on IDMA
and DMA memory maps.
Figure 10.IDMA Control/OVLAY Registers
Figure 11.Direct Memory Access—PM and DM Memory
Maps
Bootstrap Loading (Booting)The ADSP-2189M has two mechanisms to allow automatic
loading of the internal program memory after reset. The method
for booting is controlled by the Mode A, B and C configuration
bits.
When the MODE pins specify BDMA booting, the ADSP-2189M
initiates a BDMA boot sequence when reset is released.
The BDMA interface is set up during reset to the following
defaults when BDMA booting is specified: the BDIR, BMPAGE,
BIAD and BEAD registers are set to 0, the BTYPE register is
set to 0 to specify program memory 24-bit words, and the
BWCOUNT register is set to 32. This causes 32 words of on-
chip program memory to be loaded from byte memory. These
32 words are used to set up the BDMA to load in the remaining
program code. The BCR bit is also set to 1, which causes pro-
gram execution to be held off until all 32 words are loaded into
on-chip program memory. Execution then begins at address 0.
The ADSP-2100 Family development software (Revision 5.02
and later) fully supports the BDMA booting feature and can
generate byte memory space compatible boot code.
The IDLE instruction can also be used to allow the processor to
hold off execution while booting continues through the BDMA
interface. For BDMA accesses while in Host Mode, the ad-
dresses to boot memory must be constructed externally to the
ADSP-2189M. The only memory address bit provided by the
processor is A0.
IDMA Port BootingThe ADSP-2189M can also boot programs through its Internal
DMA port. If Mode C = 1, Mode B = 0, and Mode A = 1, the
ADSP-2189M boots from the IDMA port. IDMA feature can
load as much on-chip memory as desired. Program execution is
held off until on-chip program memory location 0 is written to.
ADSP-2189M
Bus Request and Bus GrantThe ADSP-2189M can relinquish control of the data and ad-
dress buses to an external device. When the external device
requires access to memory, it asserts the bus request (BR) sig-
nal. If the ADSP-2189M is not performing an external memory
access, it responds to the active BR input in the following pro-
cessor cycle by:Three-stating the data and address buses and the PMS,
DMS, BMS, CMS, IOMS, RD, WR output drivers,Asserting the bus grant (BG) signal, andHalting program execution.
If Go Mode is enabled, the ADSP-2189M will not halt program
execution until it encounters an instruction that requires an
external memory access.
If the ADSP-2189M is performing an external memory access
when the external device asserts the BR signal, it will not three-
state the memory interfaces or assert the BG signal until the
processor cycle after the access completes. The instruction does
not need to be completed when the bus is granted. If a single
instruction requires two external memory accesses, the bus will
be granted between the two accesses.
When the BR signal is released, the processor releases the BG
signal, reenables the output drivers and continues program
execution from the point at which it stopped.
The bus request feature operates at all times, including when
the processor is booting and when RESET is active.
The BGH pin is asserted when the ADSP-2189M requires the
external bus for a memory or BDMA access, but is stopped.
The other device can release the bus by deasserting bus request.
Once the bus is released, the ADSP-2189M deasserts BG and
BGH and executes the external memory access.
Flag I/O PinsThe ADSP-2189M has eight general purpose programmable
input/output flag pins. They are controlled by two memory
mapped registers. The PFTYPE register determines the direc-
tion, 1 = output and 0 = input. The PFDATA register is used to
read and write the values on the pins. Data being read from a
pin configured as an input is synchronized to the ADSP-2189M’s
clock. Bits that are programmed as outputs will read the value
being output. The PF pins default to input during reset.
In addition to the programmable flags, the ADSP-2189M has
five fixed-mode flags, FLAG_IN, FLAG_OUT, FL0, FL1 and
FL2. FL0-FL2 are dedicated output flags. FLAG_IN and
FLAG_OUT are available as an alternate configuration of
SPORT1.
Note: Pins PF0, PF1, PF2 and PF3 are also used for device
configuration during reset.
INSTRUCTION SET DESCRIPTIONThe ADSP-2189M assembly language instruction set has an
algebraic syntax that was designed for ease of coding and read-
ability. The assembly language, which takes full advantage of the
processor’s unique architecture, offers the following benefits:The algebraic syntax eliminates the need to remember cryp-
tic assembler mnemonics. For example, a typical arithmetic
add instruction, such as AR = AX0 + AY0, resembles a
simple equation.Every instruction assembles into a single, 24-bit word that
can execute in a single instruction cycle.The syntax is a superset ADSP-2100 Family assembly language
and is completely source-and-object-code-compatible with
other family members. Programs may need to be relocated to
utilize on-chip memory and conform to the ADSP-2189M’s
interrupt vector and reset vector map.Sixteen condition codes are available. For conditional jump,
call, return, or arithmetic instructions, the condition can be
checked and the operation executed in the same instruction
cycle.Multifunction instructions allow parallel execution of an
arithmetic instruction with up to two fetches or one write to
processor memory space during a single instruction cycle.
DESIGNING AN EZ-ICE-COMPATIBLE SYSTEMThe ADSP-2189M has on-chip emulation support and an ICE-
Port, a special set of pins that interface to the EZ-ICE. These
features allow in-circuit emulation without replacing the target
system processor by using only a 14-pin connection from the
target system to the EZ-ICE. Target systems must have a 14-pin
connector to accept the EZ-ICE’s in-circuit probe, a 14-pin
plug.
Issuing the chip reset command during emulation causes the
DSP to perform a full chip reset, including a reset of its memory
mode. Therefore, it is vital that the mode pins are set correctly
PRIOR to issuing a chip reset command from the emulator user
interface. If you are using a passive method of maintaining
mode information (as discussed in Setting Memory Modes),
then it does not matter that the mode information is latched by
an emulator reset. However, if using the RESET pin as a
method of setting the value of the mode pins, the effects of an
emulator reset must be taken into consideration.
One method of ensuring that the values located on the mode
pins are those desired is to construct a circuit like the one shown
in Figure 12. This circuit forces the value located on the Mode
A pin to logic high; regardless if it latched via the RESET or
ERESET pin.
Figure 12.Mode A Pin/EZ-ICE Circuit
See the ADSP-2100 Family EZ-Tools data sheet for complete
information on ICE products.
The ICE-Port interface consists of the following ADSP-2189M
pins: EBR, EINT, EE, EBG, ECLK, ERESET, ELIN, EMS,
and ELOUT.
These ADSP-2189M pins must be connected only to the EZ-
ICE connector in the target system. These pins have no function
except during emulation, and do not require pull-up or pull-
down resistors. The traces for these signals between the ADSP-
2189M and the connector must be kept as short as possible, no
longer than three inches.
The following pins are also used by the EZ-ICE: BR, BG,
RESET, and GND.
The EZ-ICE uses the EE (emulator enable) signal to take con-
trol of the ADSP-2189M in the target system. This causes the
processor to use its ERESET, EBR, and EBG pins instead of
the RESET, BR, and BG pins. The BG output is three-stated.
These signals do not need to be jumper-isolated in your system.
The EZ-ICE connects to your target system via a ribbon cable
and a 14-pin female plug. The female plug is plugged onto the
14-pin connector (a pin strip header) on the target board.
Target Board Connector for EZ-ICE ProbeThe EZ-ICE connector (a standard pin strip header) is shown in
Figure 13. You must add this connector to your target board
design if you intend to use the EZ-ICE. Be sure to allow enough
room in your system to fit the EZ-ICE probe onto the 14-pin
connector.
Figure 13.Target Board Connector for EZ-ICE
The 14-pin, 2-row pin strip header is keyed at the Pin 7 loca-
tion—you must remove Pin 7 from the header. The pins must
be 0.025 inch square and at least 0.20 inch in length. Pin spac-
ing should be 0.1 × 0.1 inches. The pin strip header must have
at least 0.15 inch clearance on all sides to accept the EZ-ICE
probe plug.
Pin strip headers are available from vendors such as 3M,
McKenzie, and Samtec.
Target Memory InterfaceFor your target system to be compatible with the EZ-ICE emu-
lator, it must comply with the memory interface guidelines listed
below.
PM, DM, BM, IOM, and CM
Design your Program Memory (PM), Data Memory (DM),
Byte Memory (BM), I/O Memory (IOM), and Composite
Memory (CM) external interfaces to comply with worst case
device timing requirements and switching characteristics as
specified in this data sheet. The performance of the EZ-ICE
may approach published worst case specification for some memory
access timing requirements and switching characteristics.
Note: If your target does not meet the worst case chip specifica-
tion for memory access parameters, you may not be able to
emulate your circuitry at the desired CLKIN frequency. De-
pending on the severity of the specification violation, you may
have trouble manufacturing your system as DSP components
statistically vary in switching characteristic and timing require-
ments within published limits.
Restriction: All memory strobe signals on the ADSP-2189M(RD, WR, PMS, DMS, BMS, CMS, and IOMS) used in your
target system must have 10 kΩ pull-up resistors connected when
the EZ-ICE is being used. The pull-up resistors are necessary
because there are no internal pull-ups to guarantee their state
during prolonged three-state conditions resulting from typical
EZ-ICE debugging sessions. These resistors may be removed at
your option when the EZ-ICE is not being used.
Target System Interface SignalsWhen the EZ-ICE board is installed, the performance on some
system signals change. Design your system to be compatible
with the following system interface signal changes introduced by
the EZ-ICE board:EZ-ICE emulation introduces an 8 ns propagation delay
between your target circuitry and the DSP on the RESET
signal.EZ-ICE emulation introduces an 8 ns propagation delay
between your target circuitry and the DSP on the BR signal.EZ-ICE emulation ignores RESET and BR when single-
stepping.EZ-ICE emulation ignores RESET and BR when in Emula-
tor Space (DSP halted).EZ-ICE emulation ignores the state of target BR in certain
modes. As a result, the target system may take control of the
DSP’s external memory bus only if bus grant (BG) is as-
serted by the EZ-ICE board’s DSP.
ADSP-2189M–SPECIFICATIONS
RECOMMENDED OPERATING CONDITIONSNOTESThe ADSP-2189M is 3.3 V tolerant (always accepts up to 3.6 Volt max VIH), but voltage compliance (on outputs, VOH) depends on the input VDDEXT; because VOH
(max) ≈ VDDEXT (max). This applies to Bidirectional pins (D0–D23, RFS0, RFS1, SCLK0, SCLK1, TFS0, TFS1, A1–A13, PF0–PF7) and Input Only pins (CLKIN,
RESET, BR, DR0, DR1, PWD).
ELECTRICAL CHARACTERISTICSNOTESBidirectional pins: D0–D23, RFS0, RFS1, SCLK0, SCLK1, TFS0, TFS1, A1–A13, PF0–PF7.Input Only pins: RESET, BR, DR0, DR1, PWD.Input Only pins: CLKIN, RESET, BR, DR0, DR1, PWD.Output pins: BG, PMS, DMS, BMS, IOMS, CMS, RD, WR, PWDACK, A0, DT0, DT1, CLKOUT, FL2-0, BGH.Although specified for TTL outputs, all ADSP-2189M outputs are CMOS-compatible and will drive to VDDEXT and GND, assuming no dc loads.Guaranteed but not tested.Three-statable pins: A0–A13, D0-D23, PMS, DMS, BMS, IOMS, CMS, RD, WR, DT0, DT1, SCLK0, SCLK1, TFS0, TFS1, RFS0, RFS1, PF0–PF7.0 V on BR.Idle refers to ADSP-2189M state of operation during execution of IDLE instruction. Deasserted pins are driven to either VDD or GND.IDD measurement taken with all instructions executing from internal memory. 50% of the instructions are multifunction (types 1, 4, 5, 12, 13, 14), 30% are type 2
and type 6, and 20% are idle instructions.VIN = 0 V and 3 V. For typical figures for supply currents, refer to Power Dissipation section.See Chapter 9 of the ADSP-2100 Family User’s Manual, Third Edition for details.Applies to LQFP package type.Output pin capacitance is the capacitive load for any three-stated output pin.VDDINT = 2.5 V. T = 25°C.
Specifications subject to change without notice.
TIMING PARAMETERS
GENERAL NOTESUse the exact timing information given. Do not attempt to
derive parameters from the addition or subtraction of others.
While addition or subtraction would yield meaningful results for
an individual device, the values given in this data sheet reflect
statistical variations and worst cases. Consequently, you cannot
meaningfully add up parameters to derive longer times.
TIMING NOTESSwitching characteristics specify how the processor changes its
signals. You have no control over this timing—circuitry external
to the processor must be designed for compatibility with these
signal characteristics. Switching characteristics tell you what the
processor will do in a given circumstance. You can also use
switching characteristics to ensure that any timing requirement
of a device connected to the processor (such as memory) is
satisfied.
Timing requirements apply to signals that are controlled by
circuitry external to the processor, such as the data input for a
read operation. Timing requirements guarantee that the proces-
sor operates correctly with other devices.
MEMORY TIMING SPECIFICATIONSThe table below shows common memory device specifications
and the corresponding ADSP-2189M timing parameters, for
your convenience.
NOTExMS = PMS, DMS, BMS, CMS or IOMS.
ABSOLUTE MAXIMUM RATINGS1NOTESStresses above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. These are stress ratings only; functional operation of the
device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.Applies to Bidirectional pins (D0–D23, RFS0, RFS1, SCLK0, SCLK1, TFS0,
TFS1, A1–A13, PF0–PF7) and Input only pins (CLKIN, RESET, BR, DR0,
DR1, PWD).Applies to Output pins (BG, PMS, DMS, BMS, IOMS, CMS, RD, WR, PWDACK,
A0, DT0, DT1, CLKOUT, FL2-0, BGH).
CAUTIONESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the ADSP-2189M features proprietary ESD protection circuitry, permanent damage
may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
ADSP-2189M
FREQUENCY DEPENDENCY FOR TIMING
SPECIFICATIONStCK is defined as 0.5tCKI. The ADSP-2189M uses an input clock
with a frequency equal to half the instruction rate: a 37.50 MHz
input clock (which is equivalent to 28 ns) yields a 13 ns proces-
sor cycle (equivalent to 75 MHz). tCK values within the range of
0.5tCKI period should be substituted for all relevant timing pa-
rameters to obtain the specification value.
Example: tCKH = 0.5tCK – 7 ns = 0.5 (15 ns) – 7 ns = 0.5 ns
ENVIRONMENTAL CONDITIONS1NOTEWhere the ambient temperature rating (TAMB) is:
TAMB = TCASE – (PD × θCA)
TCASE = Case temperature in °C
PD = Power dissipation in W.
POWER DISSIPATIONTo determine total power dissipation in a specific application,
the following equation should be applied for each output:
C × VDD2 × f
C = load capacitance, f = output switching frequency.
Example:In an application where external data memory is used and no
other outputs are active, power dissipation is calculated as follows:
Assumptions:External data memory is accessed every cycle with 50% of
the address pins switching.External data memory writes occur every other cycle with
50% of the data pins switching.Each address and data pin has a 10 pF total load at the pin.The application operates at VDDEXT = 3.3 V and tCK = 15 ns.
Total Power Dissipation = PINT + (C × VDDEXT2 × f)
PINT = internal power dissipation from Power vs. Frequency
graph (Figure 15).
(C × VDDEXT2 × f) is calculated for each output:
Address, DMS
Total power dissipation for this example is PINT + 50.7 mW.
Output Drive CurrentsFigure 14 shows typical I-V characteristics for the output drivers
on the ADSP-2189M. The curves represent the current drive
capability of the output drivers as a function of output voltage.
Figure 14.Typical Output Driver Characteristics
