ADP3334AR-REEL ,High Accuracy Low IQ, 500 mA anyCAP® Adjustable Low Dropout RegulatorFEATURES FUNCTIONAL BLOCK DIAGRAMHigh Accuracy over Line and Load: 0.9% @ 25C,1.8% over Temperat ..
ADP3334ARZ ,High Accuracy Low IQ, 500 mA anyCAP® Adjustable Low Dropout RegulatorSpecifications subject to change without notice.–2– REV. BADP3334ABSOLUTE MAXIMUM RATSINGS* PIN FUN ..
ADP3335ACPZ-3.3-R7 , High Accuracy, Ultralow IQ, 500 mA, anyCAP Low Dropout Regulator
ADP3335ARM-1.8 ,0.3-16V; 200mW; 500MHz, high accuracy ultralow 500mA anyCAP low dropout regulator. For PCMCIA card, cellular phones, camcorders and camerasapplications. The ADP3335 achieves exceptional accuracy of±0.9% at room temperature and ±1.8% over ..
ADP3335ARM-2.5 ,0.3-16V; 200mW; 500MHz, high accuracy ultralow 500mA anyCAP low dropout regulator. For PCMCIA card, cellular phones, camcorders and camerasGENERAL DESCRIPTION+ +C CIN OUTSD GNDThe ADP3335 is a member of the ADP330x family of precision 1F ..
ADP3335ARM-2.5-RL ,High Accuracy Ultralow Quiescent Current, 500mA, anyCAP® Low DropoutSpecifications subject to change without notice. No license is granted by implication www.analog.c ..
AK4356VQ , 192kHz 24 Bit IX-CHANNEL DAC FOR DVD-AUDIO
AK4356VQ , 192kHz 24 Bit IX-CHANNEL DAC FOR DVD-AUDIO
AK4357VQ , 192kHz 24-Bit 6ch DAC with DSD Input
AK4358VQ , 192 KHZ 24 BIT 8 CH DAC WITH DSD INPUT
AK4364VF , 96kHz 24BIT DAC WITH PLL AND DIT
AK4380VT , 100dB 24BIT 96kHz 2CH DAC
ADP3334ACPZ-REEL7-ADP3334ARMZ-REEL7-ADP3334AR-REEL-ADP3334ARZ
High Accuracy Low IQ, 500 mA anyCAP® Adjustable Low Dropout Regulator
REV.B
High Accuracy, Low IQ, anyCAP®Adjustable Low Dropout Regulator
FEATURES
High Accuracy over Line and Load: �0.9% @ 25�C,�1.8% over Temperature
500 mA Current Capability
Ultralow Dropout Voltage
Requires Only CO = 1.0 �F for Stability
anyCAP = Stable with Any Type of Capacitor
(Including MLCC)
Current and Thermal Limiting
Low Noise
Low Shutdown Current: < 1.0 �A (Typ)
2.6 V to 11 V Supply Range
1.5 V to 10 V Output Range
–40�C to +85�C Ambient Temperature Range
APPLICATIONS
Cellular Phones
TFT LCD Modules
Camcorders, Cameras
Networking Systems, DSL/Cable Modems
Cable Set-Top Boxes
DSP Supplies
Personal Digital Assistants
GENERAL DESCRIPTIONThe ADP3334 is a member of the ADP333x family of precision
low dropout anyCAP voltage regulators. The ADP3334 operates
with an input voltage range of 2.6 V to 11 V and delivers a
continuous load current up to 500 mA. The novel anyCAP
architecture requires only a very small 1 µF output capacitor for
stability, and the LDO is insensitive to the capacitor’s equivalent
series resistance (ESR). This makes the ADP3334 stable with any
capacitor, including ceramic (MLCC) types for space restricted
applications.
The ADP3334 achieves exceptional accuracy of ±0.9% at room
temperature and ±1.8% over temperature, line, and load. The
dropout voltage of the ADP3334 is only 200 mV (typical) at
500 mA. This device also includes a safety current limit, ther-
mal overload protection, and a shutdown feature. In shutdown
mode, the ground current is reduced to less than 1 µA. The
ADP3334 has low quiescent current of 90 µA (typical) in light
load situations.
FUNCTIONAL BLOCK DIAGRAMThe ADP3334 is available in three different package options:
1.Excellent thermal capability, space saving 3 mm � 3 mm LFCSP.
2.Popular low profile MSOP-8.
3.Traditional thermal enhanced SOIC-8.
Figure 1.Typical Application Circuit
ADP3334–SPECIFICATIONS1, 2, 3(VIN = 6.0V, CIN = COUT = 1.0 �F, TA = –40�C to +85�C, unless otherwise noted.)NOTESAll limits at temperature extremes are guaranteed via correlation using standard statistical quality control (SQC) methods.Ambient temperature of 85°C corresponds to a junction temperature of 125°C under pulsed full load test conditions.Application stable with no load.VIN = 2.6 V to 11 V for VOUT(NOM) £ 2.2 V.Ground current includes current through external resistors.
Specifications subject to change without notice.
CAUTIONESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the ADP3334 features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
ABSOLUTE MAXIMUM RATSINGS*Input Supply Voltage . . . . . . . . . . . . . . . . . . . –0.3 V to +16 V
Shutdown Input Voltage . . . . . . . . . . . . . . . . –0.3 V to +16 V
Power Dissipation . . . . . . . . . . . . . . . . . . . . Internally Limited
Operating Ambient Temperature Range . . . . –40°C to +85°C
Operating Junction Temperature Range . . . –40°C to +150°C
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
�JA 2-Layer SOIC-8 . . . . . . . . . . . . . . . . . . . . . . . . 122.3°C/W
�JA 4-Layer SOIC-8 . . . . . . . . . . . . . . . . . . . . . . . . . 86.6°C/W
�JA 2-Layer LFCSP-8 . . . . . . . . . . . . . . . . . . . . . . . . . . 62°C/W
�JA 4-Layer LFCSP-8 . . . . . . . . . . . . . . . . . . . . . . . . . . 48°C/W
�JA 2-Layer MSOP-8 . . . . . . . . . . . . . . . . . . . . . . . . . 220°C/W
�JA 4-Layer MSOP-8 . . . . . . . . . . . . . . . . . . . . . . . . .158°C/W
Lead Temperature Range (Soldering 6 sec) . . . . . . . . . . 300°C
*Stresses above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. This is a stress rating only. Functional operation of the
device at these or any other conditions above those listed in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
PIN CONFIGURATIONS
ORDERING GUIDE
PIN FUNCTION DESCRIPTIONS
MnemonicGND
OUT
ADP3334–Typical Performance CharacteristicsTPC 3. Ground Current vs.
Supply Voltage
TPC 6. Ground Current vs.
Junction Temperature
TPC 9. Power-Up Response
TPC 1. Line Regulation Output
Voltage vs. Supply Voltage
TPC 4. Ground Current vs.
Load Current
TPC 7. Dropout Voltage vs.
Output Current
TPC 2. Output Voltage vs.
Load Current
TPC 5. Output Voltage Variation %
vs. Junction Temperature
TPC 8. Power-Up/Power-Down
TPC 10. Line Transient Response
TPC 13. Load Transient Response
TPC 16. Power Supply Ripple
Rejection
TPC 11. Line Transient Response
TPC 14. Short Circuit Current
TPC 17. RMS Noise vs. CL
(10 Hz to 100 kHz)
TPC 12. Load Transient Response
TPC 15. Turn Off/On Response
TPC 18. Output Noise Density
ADP3334
THEORY OF OPERATIONThe new anyCAP LDO ADP3334 uses a single control loop for
regulation and reference functions. The output voltage is sensed
by a resistive voltage divider consisting of R1 and R2 that is
varied to provide the available output voltage option. Feedback
is taken from this network by way of a series diode (D1) and a
second resistor divider (R3 and R4) to the input of an amplifier.
Figure 2.Functional Block Diagram
A very high gain error amplifier is used to control this loop. The
amplifier is constructed in such a way that equilibrium pro-
duces a large, temperature-proportional input, “offset voltage”
that is repeatable and very well controlled. The temperature-
proportional offset voltage is combined with the complementary
diode voltage to form a “virtual band gap” voltage, implicit in
the network although it never appears explicitly in the circuit.
Ultimately, this patented design makes it possible to control
the loop with only one amplifier. This technique also improves
the noise characteristics of the amplifier by providing more
flexibility on the trade-off of noise sources that leads to a low
noise design.
The R1, R2 divider is chosen in the same ratio as the band gap
voltage to the output voltage. Although the R1, R2 resistor divider
is loaded by the diode D1 and a second divider consisting of R3
and R4, the values can be chosen to produce a temperature stable
output. This unique arrangement specifically corrects for the
loading of the divider, thus avoiding the error resulting from
base current loading in conventional circuits.
The patented amplifier controls a new and unique noninverting
driver that drives the pass transistor, Q1. The use of this special
noninverting driver enables the frequency compensation to
include the load capacitor in a pole-splitting arrangement to
achieve reduced sensitivity to the value, type, and ESR of the
load capacitance.
Most LDOs place very strict requirements on the range of ESR
values for the output capacitor because they are difficult to stabilize
due to the uncertainty of load capacitance and resistance. More-
over, the ESR value, required to keep conventional LDOs stable,
changes depending on load and temperature. These ESR limita-
tions make designing with LDOs more difficult because of their
unclear specifications and extreme variations over temperature.
With the ADP3334 anyCAP LDO, this is no longer true. It can
be used with virtually any good quality capacitor, with no con-
straint on the minimum ESR. This innovative design allows the
circuit to be stable with just a small 1 mF capacitor on the out-
superior line noise rejection and very high regulator gain, which
lead to excellent line and load regulation. An impressive ±1.8%
accuracy is guaranteed over line, load, and temperature.
Additional features of the circuit include current limit and ther-
mal shutdown.
APPLICATION INFORMATION
Output CapacitorAs with any micropower device, output transient response is a
function of the output capacitance. The ADP3334 is stable with
a wide range of capacitor values, types, and ESR (anyCAP).
A capacitor as low as 1 µF is all that is needed for stability;
larger capacitors can be used if high output current surges are
anticipated. The ADP3334 is stable with extremely low ESR
capacitors (ESR�0), such as multilayer ceramic capacitors
(MLCC) or OSCON. Note that the effective capacitance of some
capacitor types may fall below the minimum over the operating
temperature range or with the application of a dc voltage.
Input Bypass CapacitorAn input bypass capacitor is not strictly required but is advisable
in any application involving long input wires or high source
impedance. Connecting a 1 µF capacitor from IN to ground
reduces the circuit’s sensitivity to PC board layout. If a larger
value output capacitor is used, then a larger value input capaci-
tor is also recommended.
Noise Reduction CapacitorA noise reduction capacitor (CNR) can be placed between the
output and the feedback pin to further reduce the noise by
6dB to 10dB (TPC 18). Low leakage capacitors in the 100 pF
to 1nF range provide the best performance. Since the feedback
pin (FB) is internally connected to a high impedance node, any
connection to this node should be carefully done to avoid noise
pickup from external sources. The pad connected to this pin
should be as small as possible, and long PC board traces are not
recommended.
When adding a noise reduction capacitor, maintain a mini-
mum load current of 1 mA when not in shutdown.
It is important to note that as CNR increases, the turn-on time
will be delayed. With CNR values of 1 nF, this delay may be
on the order of several milliseconds.
Figure 3.Typical Application Circuit
Output VoltageThe ADP3334 has an adjustable output voltage that can be set
by an external resistor divider. The output voltage will be divided
by R1 and R2 and then fed back to the FB pin.
