ADN8831ACPZ-REEL7 ,A High Efficiency TEC Controller SolutionGENERAL DESCRIPTION True current sensing and over current protection The ADN8831 is a monolithic co ..
ADNS-3040 ,Packard) - Ultra Low-Power Mouse Sensor
ADNS-3060 ,ADNS-3060 · High Performance Optical Mouse Sensor (Optimized For Gaming And Office Environments)Features••••• High speed motion detection – upto 40 ips and 15g••••• New architecture for greatlyDe ..
ADNS-5020-EN , Optical Mouse Sensor
ADNS-5090 , Trim Lens for LED Mouse
ADNS-5100 , Solid-State Optical Mouse Lens
AIC809-46CUTR , 3-PIN MICROPROCESSOR RESET CIRCUITS
AIC809-46CUTR , 3-PIN MICROPROCESSOR RESET CIRCUITS
AIC810-44CUTR , 3-PIN MICROPROCESSOR RESET CIRCUITS
AIC810-44PUTR , 3-PIN MICROPROCESSOR RESET CIRCUITS
AIVR3K42 , APLUS INTEGRATED CIRCUITS INC
AK002M4-31 , GaAs MMIC Control FET in SOT 143 DC-2.5 GHz
ADN8831ACPZ-REEL7
A High Efficiency TEC Controller Solution
Thermoelectric Cooler (TEC)
Controller
FEATURES
True current sensing and over current protection
Separate heating and cooling current limits
High efficiency: >90%
Long-term temperature stability: 0.1°C
Temperature lock indication
Temperature monitoring output
Oscillator synchronization with an external signal
Clock phase adjustment for multiple controllers
Programmable switching frequency up to 1MHz
Programmable maximum TEC voltage
Low noise: <0.05% TEC current ripple
TEC current monitoring
Compact 5mm x 5mm LFCSP
APPLICATIONS
Thermoelectric Cooler (TEC) temperature control
Resistive heating element control
Temperature-Stabilization Substrate (TSS) control
FUNCTIONAL BLOCK DIAGRAM Heating ILim
Cooling ILim VLim Freq/Phase Control
TempSet Input
Thermistor
GENERAL DESCRIPTION The ADN8831 is a monolithic controller that drives a
Thermoelectric Cooler (TEC) to stabilize the temperature of a
laser diode or a passive component used in
telecommunications equipment.
This device relies on a Negative Temperature Coefficient
(NTC) thermistor or a positive temperature coefficient RTD
device to sense the temperature of the object attached to the
TEC. The target temperature is set with an analog input
voltage either from a DAC or with an external resistor divider.
The loop is stabilized by a PID compensation amplifier with
high stability and low noise. The compensation network can
be adjusted by the user to optimize temperature settling time.
The component values for this network can be calculated
based on the thermal transfer function of the laser diode or
obtained from the look-up table given in the applications
notes.
Voltage outputs are provided to monitor both the temperature
of the object and the voltage across the TEC. A 2.5V voltage
reference is provided for the thermistor temperature sensing
bridge.
An external sense resistor provides true current sensing.
Current limits for both heating and cooling can be set
independently.
TABLE OF CONTENTS Specifications 3
Absolute Maximum Ratings 5
Pin Configuration.........................................................................6
Pin Descriptions...........................................................................6
Theory of Operation 9
Introduction...................................................................................9
Outline Dimensions 10
Ordering Guide 11
REVISION HISTORY Revision PrC
7/03—Data Sheet Changed from REV PrB to REV PrC.
SPECIFICATIONS
Table 1. ADN8831—Electrical Characteristics (V+ = 3.0 V to 5.5 V, TA = 25°C, unless otherwise noted.)
Table 2. ADN8831—Electrical Characteristics (V+ = 3.0 V to 5.5 V, TA = 25°C, unless otherwise noted.)
ABSOLUTE MAXIMUM RATINGS
Table 3. Absolute Maximum Ratings (at 25°C, unless
otherwise noted)
Table 2. Thermal Resistance 1 θJA is specified for the worst-case conditions, i.e., θJA is specified for device
soldered in circuit board for surface mount packages.
Pin Configuration
Pin Descriptions
