ADM8617RCYAKS-RL7 ,Low Voltage Supervisory Circuit with Watchdog and Open-Drain RESET Output in 4-Lead SC70GENERAL DESCRIPTION Each part is available in a choice of the following 9 reset The ADM8611/ADM8616 ..
ADM8618 ,Low-Voltage Manual Reset & Watchdog Supervisory Circuits in 4-Lead SC70FEATURES FUNCTIONAL BLOCK DIAGRAMS Precision 1.8V to 5V Power Supply Monitoring 9 Reset Threshold ..
ADM8660AN ,CMOS Switched-Capacitor Voltage ConvertersSPECIFICATIONSnoted)Parameter Min Typ Max Units Test Conditions/CommentsInput Voltage, V+ R = 1 kΩL ..
ADM8660AR ,CMOS Switched-Capacitor Voltage ConvertersFEATURESTYPICAL CIRCUIT CONFIGURATIONSADM660: Inverts or Doubles Input Supply VoltageADM8660: Inver ..
ADM8660ARZ ,CMOS Switched-Capacitor Voltage Converter w/ Low Power Shutdown PinSpecifications subject to change without notice.–2– REV. BADM660/ADM8660ABSOLUTE MAXIMUM RATINGS*Po ..
ADM8660ARZ-REEL , CMOS Switched-Capacitor Voltage Converters
AIC2951D-50CS , Low Dropout Linear Regulator
AIC3842CN , Current-Mode PWM Controller
AIC3843CNTB , Current-Mode PWM Controller
AIC3843CNTB , Current-Mode PWM Controller
AIC809-46CUTR , 3-PIN MICROPROCESSOR RESET CIRCUITS
AIC809-46CUTR , 3-PIN MICROPROCESSOR RESET CIRCUITS
ADM8611LABKSZ-RL7-ADM8616-ADM8617RCYAKS-RL7
Low Voltage Supervisory Circuit with Manual Reset and Active-Low, Push-Pull Reset Output in 4-Lead SC70
Low-Voltage Manual Reset & Watchdog
Supervisory Circuits in 4-Lead SC70
Rev. PrB
FEATURES
Precision 1.8V to 5V Power Supply Monitoring
9 Reset Threshold Options:
1.58V to 4.63V
140ms (Min) Reset Timeout
Manual Reset Input (ADM8611)
Watchdog Timer (ADM8616–ADM8618)
Reset Output Stages
Push-Pull Active-Low
Open-Drain Active-Low
Push-Pull Active-High
Low Power Consumption (3µA)
Guaranteed Reset Output valid to VCC=1V
Power Supply Glitch Immunity
Specified Over -40°C to +85°C Temperature Range
4-Lead SC70 Package
APPLICATIONS
Microprocessor Systems
Computers
Controllers
Intelligent Instruments
Portable Equipment
GENERAL DESCRIPTION The ADM8611/ADM8616/ADM8617/ADM8618 are
supervisory circuits which monitor power supply voltage levels
and code execution integrity in microprocessor-based systems.
A power-on-reset signal is generated when the supply voltage
rises to a preset threshold level. The ADM8611’s debounced
manual reset input can be used to initiate a reset by means of an
external push-button or logic signal. The ADM8616–ADM8618
have an on-chip watchdog timer which can reset the
microprocessor if it fails to strobe within a preset timeout
period.
FUNCTIONAL BLOCK DIAGRAMS ���
�����
���
���
Figure 1.
Each part is available in a choice of the following 9 reset
threshold options: 1.58V, 1.67V, 2.19V, 2.32V, 2.63V, 2.93V,
3.08V, 4.38V and 4.63V. The reset timeout periods are 20ms
(min) and 140ms (min) for the ADM8611 and ADM8616–
ADM8618, respectively. The watchdog timeout period is 1.6s
(typ). The parts differ in terms of reset output configuration, as
indicated in table 1.
The ADM8611/ADM8616/ADM8617/ADM8618 are available
in 4-lead SC70 packages and typically consume only 3µA,
making them suitable for use in low power portable
applications.
Table 1. Selection Table
ADM8611/ADM8616/ADM8617/ADM8618—SPECIFICATIONS
Table 2. VCC=Full Operating Range, TA=TMIN to TMAX, unless otherwise noted
ABSOLUTE MAXIMUM RATINGS
Table 3. TA = 25°C unless otherwise noted. Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only and functional operation of the device at these or
any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
PIN CONFIGURATIONS AND FUNCTIONAL DESCRIPTIONS
Table 4. Pin Functional Descriptions
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the
human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
OUTLINE DIMENSIONS
Figure 2. 4-Lead Plastic Surface Mount Package [SC70]
(KS-4)
Dimensions shown in millimeters
ORDERING GUIDE (ADM8611/ADM8616)
