74VHC541 ,Octal Buffer/Line Driver with TRI-STATE OutputsAbsolute Maximum Ratings are those values beyond which damage to the device may occur. Functional o ..
74VHC541FT ,74VHC CMOS logic IC seriesFeatures(1) High speed: Propagation delay time = 3.7 ns (typ.) at V = 5 VCC(2) Low power dissipatio ..
74VHC541FT ,74VHC CMOS logic IC seriesabsolute maximum ratings, even briefly, lead to deterioration in IC performance or evendestruction. ..
74VHC541M ,OCTAL BUS BUFFER WITH 3 STATE OUTPUTS (NON INVERTED)74VHC541 Octal Buffer/Line Driver with 3-STATE OutputsAugust 1993Revised April 199974VHC541Octal Bu ..
74VHC541MTC ,Octal Buffer/Line Driver with 3-STATE OutputsElectrical CharacteristicsT = 25°CT = - 40°C to +85°CV A ACCSymbol Parameter Units Conditions(V)Min ..
74VHC541MTCX ,Octal Buffer/Line Driver with 3-STATE OutputsGeneral Descriptionapplied to the input pins without regard to the supply volt-The VHC541 is an adv ..
74VHC541
Octal Buffer/Line Driver with TRI-STATE Outputs
1/12November 2004 HIGH SPEED: tPD = 3.5 ns (TYP.) at VCC = 5V LOW POWER DISSIPATION:
ICC = 4 μA (MAX.) at TA=25°C HIGH NOISE IMMUNITY:NIH = VNIL = 28% VCC (MIN.) POWER DOWN PROTECTION ON INPUTS SYMMETRICAL OUTPUT IMPEDANCE:
|IOH| = IOL = 8 mA (MIN) BALANCED PROPAGATION DELAYS: PLH ≅ t PHL OPERATING VOLTAGE RANGE:
VCC(OPR) = 2V to 5.5V PIN AND FUNCTION COMPATIBLE WITH
74 SERIES 541 IMPROVED LATCH-UP IMMUNITY LOW NOISE: VOLP = 0.9V (MAX.)
DESCRIPTIONThe 74VHC541 is an advanced high-speed
CMOS OCTAL BUS BUFFER (3-STATE)
fabricated with sub-micron silicon gate and
double-layer metal wiring C2 MOS technology.
The 3 STATE control gate operates as two input
AND such that if either G1 or G2 are high, all eight
outputs are in the high impedance state.
In order to enhance PC board layout, the
74VHC541 offers a pinout having inputs and
outputs on opposite sides of the package.
Power down protection is provided on all inputs
and 0 to 7V can be accepted on inputs with no
regard to the supply voltage. This device can be
used to interface 5V to 3V.
All inputs and outputs are equipped with
protection circuits against static discharge, giving
them 2KV ESD immunity and transient excess
voltage.
74VHC541OCTAL BUS BUFFER
WITH 3 STATE OUTPUTS (NON INVERTED)
Figure 1: Pin Connection And IEC Logic Symbols
Table 1: Order Codes Rev. 4
74VHC5412/12
Figure 2: Input Equivalent Circuit Table 2: Pin Description
Table 3: Truth Table X : Don’t care
Z : High impedance
Table 4: Absolute Maximum Ratings Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is
not implied
Table 5: Recommended Operating Conditions 1) VIN from 30% to 70% of VCC
74VHC5413/12
Table 6: DC Specifications
74VHC5414/12
Table 7: AC Electrical Characteristics (Input tr = tf = 3ns)
(*) Voltage range is 3.3V ± 0.3V
(**) Voltage range is 5.0V ± 0.5V
Note 1: Parameter guaranteed by design. tsoLH = |tpLHm - tpLHn|, tsoHL = |tpHLm - tpHLn|
Table 8: Capacitive Characteristics 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without
load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/8 (per
Circuit)
74VHC5415/12
Table 9: Dynamic Switching Characteristics 1) Worst case package.
2) Max number of outputs defined as (n). Data inputs are driven 0V to 5.0V, (n-1) outputs switching and one output at GND.
3) Max number of data inputs (n) switching. (n-1) switching 0V to 5.0V. Inputs under test switching: 5.0V to threshold (VILD), 0V to threshold
(VIHD), f=1MHz.
Figure 3: Test Circuit CL =15/50pF or equivalent (includes jig and probe capacitance)
RL = R1 = 1KΩ or equivalent
RT = ZOUT of pulse generator (typically 50Ω)
74VHC5416/12
Figure 4: Waveform - Propagation Delays (f=1MHz; 50% duty cycle)
Figure 5: Waveform - Output Enable And Disable Time (f=1MHz; 50% duty cycle)
