74VHC374M ,OCTAL D-TYPE FLIP FLOP WITH 3-STATE OUTPUT NON INVERTING74VHC374 Octal D-Type Flip-Flop with 3-STATE OutputsNovember 1992Revised April 199974VHC374Octal D- ..
74VHC374M ,OCTAL D-TYPE FLIP FLOP WITH 3-STATE OUTPUT NON INVERTING74VHC374OCTAL D-TYPE FLIP FLOPWITH 3 STATE OUTPUTS NON INVERTING■ HIGH SPEED: ..
74VHC374MSCX , Octal D-Type Flip-Flop with 3-STATE OutputsFunctional Description Truth TableThe VHC374 consists of eight edge-triggered flip-flops withInputs ..
74VHC374MTC ,Octal D-Type Flip-Flop with 3-STATE OutputsFunctional Description Truth TableThe VHC374 consists of eight edge-triggered flip-flops withInputs ..
74VHC374MTCX ,Octal D-Type Flip-Flop with 3-STATE OutputsFunctional Description Truth TableThe VHC374 consists of eight edge-triggered flip-flops withInputs ..
74VHC374MX ,Octal D-Type Flip-Flop with 3-STATE OutputsGeneral Descriptioncuit prevents device destruction due to mismatched supplyThe VHC374 is an advanc ..
88E1040 , Alaska® Quad Gigabit Ethernet Transceivers
74VHC374M
OCTAL D-TYPE FLIP FLOP WITH 3-STATE OUTPUT NON INVERTING
1/11June 2001 HIGH SPEED:
fMAX = 270 MHz (TYP .) at VCC = 5V LOW POWER DISSIPATION:CC = 4 μA (MAX.) at TA =25°C HIGH NOISE IMMUNITY:NIH = VNIL = 28% VCC (MIN.) POWER DOWN PROTECTION ON INPUTS SYMMETRICAL OUTPUT IMPEDANCE:OH | = IOL = 8 mA (MIN) BALANCED PROPAGATION DELAYS: PLH ≅ t PHL OPERATING VOLTAGE RANGE:CC (OPR) = 2V to 5.5V PIN AND FUNCTION COMPATIBLE WITH
74 SERIES 374 IMPROVED LATCH-UP IMMUNITY LOW NOISE: V OLP = 0.9V (MAX.)
DESCRIPTIONThe 74VHC374 is an advanced high-speed
CMOS OCTAL D-TYPE FLIP FLOP with 3
STATE OUTPUTS NON INVERTING fabricated
with sub-micron silicon gate and double-layer
metal wiring C2 MOS technology.
These 8 bit D-Type latch are controlled by a clock
input (CK) and an output enable input (OE).
On the positive transition of the clock, the Q
outputs will be set to the logic state that were
setup at the D inputs.
While the (OE) input is low, the 8 outputs will be in
a normal logic state (high or low logic level) and
while high level the outputs will be in a high
impedance state.
The Output control does not affect the internal
operation of flip flops; that is, the old data can be
retained or the new data can be entered even
while the outputs are off. Power down protection is
provided on all inputs and 0 to 7V can be accepted
on inputs with no regard to the supply voltage.
This device can be used to interface 5V to 3V.
All inputs and outputs are equipped with
protection circuits against static discharge, giving
them 2KV ESD immunity and transient excess
voltage.
74VHC374OCTAL D-TYPE FLIP FLOP
WITH 3 STATE OUTPUTS NON INVERTING
PIN CONNECTION AND IEC LOGIC SYMBOLS
ORDER CODES
74VHC3742/11
INPUT EQUIVALENT CIRCUIT PIN DESCRIPTION
TRUTH TABLE X : Don’t Care
Z : High Impedance
LOGIC DIAGRAM This logic diagram has not be used to estimate propagation delays
74VHC3743/11
ABSOLUTE MAXIMUM RATINGS Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is
not implied
RECOMMENDED OPERATING CONDITIONS 1) VIN from 30% to 70% of VCC
74VHC3744/11
DC SPECIFICATIONS
74VHC3745/11
AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 3ns)
(*) Voltage range is 3.3V ± 0.3V
(**) Voltage range is 5.0V ± 0.5V
Note 1 : Parameter guaranteed by design. tsoLH = |tpLHm - tpLHn|, tsoHL = |tpHLm - tpHLn|
CAPACITIVE CHARACTERISTICS 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without
load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/8 (per
Flip-Flop)
74VHC3746/11
DYNAMIC SWITCHING CHARACTERISTICS 1) Worst case package.
2) Max number of outputs defined as (n). Data inputs are driven 0V to 5.0V, (n-1) outputs switching and one output at GND.
3) Max number of data inputs (n) switching. (n-1) switching 0V to 5.0V. Inputs under test switching: 5.0V to threshold (VILD), 0V to threshold
(VIHD), f=1MHz.
TEST CIRCUIT CL =15/50pF or equivalent (includes jig and probe capacitance)
RL = R1 = 1KΩ or equivalent
RT = ZOUT of pulse generator (typically 50Ω)
