74LVC2G125DP ,Dual bus buffer/line driver; 3-stateINTEGRATED CIRCUITSDATA SHEET74LVC2G125Dual bus buffer/line driver; 3-stateProduct specification 200 ..
74LVC2G125GD ,Dual bus buffer/line driver; 3-state 74LVC2G125Dual bus buffer/line driver; 3-stateRev. 14 — 29 March 2013 Product data sheet1.
74LVC2G125GT ,Dual bus buffer/line driver; 3-stateGeneral descriptionThe 74LVC2G125 provides a dual non-inverting buffer/line driver with 3-state out ..
74LVC2G126DC ,Dual bus buffer/line driver; 3-stateFeatures and benefits Wide supply voltage range from 1.65 V to 5.5 V 5 V tolerant input/output fo ..
74LVC2G126DCURE4 , DUAL BUS BUFFER GATE WITH 3-STATE OUTPUTS
74LVC2G126DCUTE4 ,Dual Bus Buffer Gate With 3-State Outputs 8-VSSOP -40 to 125Features... 18.3 Feature Description...... 92 Applications..... 18.4 Device Functional Modes...... ..
8209-6009 , 3M D Sub Plug Plug Connector
8209-6009 , 3M D Sub Plug Plug Connector
82103C , Miniature Surface Mount Power Inductors
82107 ,IR Receiver Modules for Remote Control SystemsRev. 5, 15-Oct-2002 3T ,T – Output Pulse Width ( ms )E / E – Rel. Responsivity ..
82107 ,IR Receiver Modules for Remote Control SystemsRev. 5, 15-Oct-2002 1CircuitTSOP22..YA1VISHAYVishay SemiconductorsParameter Test condition Symbol V ..
82356120100 , 0603 ESD Suppressor
74LVC2G125DP
Dual bus buffer/line driver 3-state
Philips Semiconductors Product specification
Dual bus buffer/line driver; 3-state 74L VC2G125
FEATURES Wide supply voltage range from 1.65Vto 5.5V5 V tolerant input/output for interfacing with 5 V logic High noise immunity Complies with JEDEC standard: JESD8-7 (1.65Vto 1.95V) JESD8-5 (2.3Vto 2.7V) JESD8B/JESD36 (2.7Vto 3.6V). ESD protection: HBM EIA/JESD22-A114-B exceeds 2000V MM EIA/JESD22-A115-A exceeds 200V.
•±24 mA output drive (VCC= 3.0V) CMOS low power consumption Latch-up performance exceeds 250 mA Direct interface with TTL levels Inputs accept voltages up to 5V Multiple package options Specified from −40°Cto +85°C and −40°Cto +125 °C.
DESCRIPTIONThe 74LVC2G125 is a high-performance, low-power,
low-voltage, Si-gate CMOS device and superior to most
advanced CMOS compatible TTL families.
Inputs can be driven from either 3.3Vor5 V devices.
This feature allows the useof these devicesas translators
in a mixed 3.3V and5 V environment.
This device is fully specified for partial power-down
applications using Ioff. TheIoff circuitry disables the output,
preventing the damaging backflow current through the
device when it is powered down.
The 74LVC2G125 providesa dualnon-inverting buffer/line
driver with 3-state output. The 3-state outputis controlled
by the output enable input (pin nOE). A HIGH-level at
pin nOE causes the output to assume a high-impedance
OFF-state. Schmitt-trigger action at all inputs makes the
circuit highly tolerant for slower input rise and fall times.
QUICK REFERENCE DATAGND=0 V; Tamb =25 °C.
Notes CPD is used to determine the dynamic power dissipation (PDin μW). =CPD× VCC2×fi× N+ ∑(CL× VCC2× fo) where:= input frequency in MHz;= output frequency in MHz;= output load capacitance in pF;
VCC= supply voltage in Volts;= total load switching outputs;
∑(CL× VCC2×fo)= sum of outputs. The condition is VI= GND to VCC.
Philips Semiconductors Product specification
Dual bus buffer/line driver; 3-state 74L VC2G125
FUNCTION TABLESee note1.
Note H= HIGH voltage level;= LOW voltage level;= don’t care;= high-impedance OFF-state.
ORDERING INFORMATION
PINNING
Philips Semiconductors Product specification
Dual bus buffer/line driver; 3-state 74L VC2G125
Philips Semiconductors Product specification
Dual bus buffer/line driver; 3-state 74L VC2G125
RECOMMENDED OPERATING CONDITIONS
LIMITING VALUES accordance with the Absolute Maximum Rating System (IEC 60134); voltages are referencedto GND (ground=0 V).
Notes The input and output voltage ratings may be exceeded if the input and output current ratings are observed. When VCC=0 V (Power-down mode), the output voltage can be 5.5 V in normal operation.
Philips Semiconductors Product specification
Dual bus buffer/line driver; 3-state 74L VC2G125
CHARACTERISTICSAt recommended operating conditions; voltages are referenced to GND (ground=0 V).
Philips Semiconductors Product specification
Dual bus buffer/line driver; 3-state 74L VC2G125
Note All typical values are measured at VCC= 3.3 V and Tamb =25 °C.
Philips Semiconductors Product specification
Dual bus buffer/line driver; 3-state 74L VC2G125
CHARACTERISTICSGND=0V.
Note All typical values are measured at Tamb =25 °C.
