74LVC244A ,Octal Buffer/Line Driver with 3 State OutputsAbsolute Maximum Ratings are those values beyond which damage to the device may occur. Functional o ..
74LVC244ABQ ,Octal buffer/line driver; 3-state
74LVC244ABQ ,Octal buffer/line driver; 3-stateGeneral descriptionThe 74LVC244A; 74LVCH244A is an octal non-inverting buffer/line driver with 3-st ..
74LVC244AD ,Octal buffer/line driver; 3-stateINTEGRATED CIRCUITS74LVC244A/74LVCH244AOctal buffer/line driver with 5-volt tolerantinputs/outputs ..
74LVC244ADB ,Octal buffer/line driver; 3-stateFEATURES DESCRIPTIONThe 74LVC244A/74LVCH244A is a high-performance, low-power,• 5-volt tolerant in ..
74LVC244AM ,LOW VOLTAGE CMOS OCTAL BUS BUFFER (3-STATE) HIGH PERFORMANCEAbsolute Maximum Ratings are those values beyond which damage to the device may occur. Functional o ..
8-188275-4 , AMP Micro-Match Miniature Connector System
81C55 ,2048-Bit CMOS STATIC RAM WITH I/O PORTS AND TIMER
81C55 ,2048-Bit CMOS STATIC RAM WITH I/O PORTS AND TIMER
81CNQ035ASL ,35V 80A Schottky Common Cathode Diode in a D61-8-SL packageFeaturesThe 81CNQ...A center tap Schottky rectifier module series hasbeen optimized for low reverse ..
81CNQ035ASM ,35V 80A Schottky Common Cathode Diode in a D61-8-SM packageBulletin PD-20040 rev. A 09/0181CNQ...A SERIESSCHOTTKY RECTIFIER80 AmpNew GenIII D-61 Package ..
81CNQ040A ,40V 80A Schottky Common Cathode Diode in a D61-8 packageBulletin PD-20040 rev. A 09/0181CNQ...A SERIESSCHOTTKY RECTIFIER80 AmpNew GenIII D-61 Package ..
74LVC244A
Octal Buffer/Line Driver with 3 State Outputs
1/12July 2004 5V TOLERANT INPUTS HIGH SPEED: tPD = 5.9ns (MAX.) at VCC = 3V POWER DOWN PROTECTION ON INPUTS
AND OUTPUTS SYMMETRICAL OUTPUT IMPEDANCE:
|IOH| = IOL = 24mA (MIN) at VCC = 3V PCI BUS LEVELS GUARANTEED AT 24 mA BALANCED PROPAGATION DELAYS:
tPLH ≅ tPHL OPERATING VOLTAGE RANGE:
VCC(OPR) = 1.65V to 3.6V (1.2V Data
Retention) PIN AND FUNCTION COMPATIBLE WITH
74 SERIES 244 LATCH-UP PERFORMANCE EXCEEDS
500mA (JESD 17) ESD PERFORMANCE:
HBM > 2000V (MIL STD 883 method 3015);
MM > 200V
DESCRIPTIONThe 74LVC244A is a low voltage CMOS OCTAL
BUS BUFFER (3-STATE) fabricated with
sub-micron silicon gate and double-layer metal
wiring C2 MOS technology. It is ideal for 1.65 to 3.6CC operations and low power and low noise
applications.
It can be interfaced to 5V signal environment for
inputs in mixed 3.3/5V system.
G control output governs four BUS BUFFERs.
This device is designed to be used with 3 state
memory address drivers, etc.
It has more speed performance at 3.3V than 5V
AC/ACT family, combined with a lower power
consumption.
All inputs and outputs are equipped with
protection circuits against static discharge, giving
them 2KV ESD immunity and transient excess
voltage.
74LVC244ALOW VOLTAGE CMOS QUAD BUS BUFFERS (3-STATE)
HIGH PERFORMANCE
Figure 1: Pin Connection And IEC Logic Symbols
Table 1: Order Codes Rev. 5
74LVC244A2/12
Figure 2: Input And Output Equivalent Circuit
Table 2: Pin Description Table 3: Truth Table X : Don’t care
Z : High Impedance
Table 4: Absolute Maximum Ratings Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is
not implied
1) IO absolute maximum rating must be observed
2) VO < GND
74LVC244A3/12
Table 5: Recommended Operating Conditions 1) Truth Table guaranteed: 1.2V to 3.6V
2) VIN from 0.8V to 2V at VCC = 3.0V
Table 6: DC Specifications
74LVC244A4/12
Table 7: Dynamic Switching Characteristics 1) Number of output defined as "n". Measured with "n-1" outputs switching from HIGH to LOW or LOW to HIGH. The remaining output is
measured in the LOW state.
Table 8: AC Electrical Characteristics 1) Skew is defined as the absolute value of the difference between the actual propagation delay for any two outputs of the same device switch-
ing in the same direction, either HIGH or LOW (tOSLH = | tPLHm - tPLHn|, tOSHL = | tPHLm - tPHLn|
2) Parameter guaranteed by design
Table 9: Capacitive Characteristics 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without
load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/n (per circuit)
74LVC244A5/12
Figure 3: Test Circuit RT = ZOUT of pulse generator (typically 50Ω)
Table 10: Test Circuit And Waveform Symbol Value
Figure 4: Waveform - Propagation Delays (f=1MHz; 50% duty cycle)
74LVC244A6/12
Figure 5: Waveform - Output Enable And Disable Time (f=1MHz; 50% duty cycle)
