74LVC1G58GM ,Low-power configurable multiple function gateFeatures and benefits Wide supply voltage range from 1.65 V to 5.5 V 5 V tolerant input/output fo ..
74LVC1G58GW ,Low-power configurable multiple function gateapplications using I . The I circuitryoff offdisables the output, preventing the damaging backflow c ..
74LVC1G58GW ,Low-power configurable multiple function gateGeneral descriptionThe 74LVC1G58 provides configurable multiple functions. The output state is dete ..
74LVC1G66GM ,Bilateral switchPin configuration SOT891 SOT353-1 and SOT753 and SOT1115 and SOT12026.2 Pin description Table 3. Pi ..
74LVC1G66GV ,Bilateral switchLogic diagram74LVC1G66 All information provided in this document is subject to legal disclaimers. ..
74LVC1G66GW ,Bilateral switchGeneral descriptionThe 74LVC1G66 provides one single pole, single-throw analog switch function. It ..
81487EIB ,【15kV ESD Protected, 1/8 Unit Load, 5V, Low Power, High Speed or Slew Rate Limited, RS-485/RS-422 Transceivers
8155H-2 , 2048-BIT STATIC HMOS RAM WITH I/O PORTS AND TIMER
8169 ,DIGITAL AUDIO PROCESSOR WITH MULTICHANNEL DDX⑩applications with commercial audio D/A converters. The output sampling frequency is fixed at 48 kHz ..
8-188275-4 , AMP Micro-Match Miniature Connector System
81C55 ,2048-Bit CMOS STATIC RAM WITH I/O PORTS AND TIMER
81C55 ,2048-Bit CMOS STATIC RAM WITH I/O PORTS AND TIMER
74LVC1G58GM -74LVC1G58GW
Low-power configurable multiple function gate
1. General descriptionThe 74LVC1G58 provides configurable multiple functions. The output state is determined
by eight patterns of 3-bit input. The user can choose the logic functions AND, OR, NAND,
NOR, XOR, inverter and buffer. All inputs can be connected to VCC or GND.
Inputs can be driven from either 3.3 Vor5 V devices. This feature allows the use of this
device in a mixed 3.3 V and5 V environment.
This device is fully specified for partial power-down applications using IOFF. The IOFF
circuitry disables the output, preventing the damaging backflow current through the device
when it is powered down.
All inputs (A, B and C) are Schmitt trigger inputs. They are capable of transforming slowly
changing input signals into sharply defined, jitter-free output signals.
2. Features and benefits Wide supply voltage range from 1.65 V to 5.5V5 V tolerant input/output for interfacing with 5 V logic High noise immunity Complies with JEDEC standard: JESD8-7 (1.65 V to 1.95V) JESD8-5 (2.3 V to 2.7V) JESD8B/JESD36 (2.7 V to 3.6 V). ESD protection: HBM JESD22-A114F exceeds 2000V MM JESD22-A115-A exceeds 200V. 24 mA output drive (VCC =3.0V) CMOS low power consumption Latch-up performance exceeds 250 mA Direct interface with TTL levels Inputs accept voltages up to 5V Multiple package options Specified from 40 C to +85 C and 40 C to +125 C.
74L VC1G58
Low-power configurable multiple function gate
Rev. 8 — 22 April 2014 Product data sheet
NXP Semiconductors 74LVC1G58
Low-power configurable multiple function gate
3. Ordering information
4. Marking[1] The pin 1 indicator is located on the lower left corner of the device, below the marking code.
5. Functional diagram
Table 1. Ordering information
Table 2. Marking
NXP Semiconductors 74LVC1G58
Low-power configurable multiple function gate
6. Pinning information
6.1 Pinning
6.2 Pin description
7. Functional description[1] H= HIGH voltage level; L= LOW voltage level
Table 3. Pin description
Table 4. Function table[1]
NXP Semiconductors 74LVC1G58
Low-power configurable multiple function gate
7.1 Logic configurations
Table 5. Function selection table
NXP Semiconductors 74LVC1G58
Low-power configurable multiple function gate
8. Limiting values[1] The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
[2] When VCC=0 V (Power-down mode), the output voltage can be 5.5 V in normal operation.
[3] For SC-88 and SC-74 packages: above 87.5 C the value of Ptot derates linearly with 4.0 mW/K.
For XSON6 packages: above 118 C the value of Ptot derates linearly with 7.8 mW/K.
9. Recommended operating conditions
Table 6. Limiting valuesIn accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
Table 7. Recommended operating conditions
NXP Semiconductors 74LVC1G58
Low-power configurable multiple function gate
10. Static characteristicsTable 8. Static characteristicsAt recommended operating conditions; voltages are referenced to GND (ground = 0 V).
NXP Semiconductors 74LVC1G58
Low-power configurable multiple function gate[1] Typical values are measured at maximum VCC and Tamb= 25 C.
11. Dynamic characteristics[1] Typical values are measured at nominal VCC and at Tamb= 25 C.
[2] tpd is the same as tPLH and tPHL
[3] CPD is used to determine the dynamic power dissipation (PD in W).
PD = CPD VCC 2 fi N + (CL VCC 2 fo) where:
fi = input frequency in MHz;
fo = output frequency in MHz;
CL = output load capacitance in pF;
VCC = supply voltage in V;
N = number of inputs switching;
(CL VCC 2 fo) = sum of outputs.
Table 8. Static characteristics …continuedAt recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Table 9. Dynamic characteristicsVoltages are referenced to GND (ground=0 V); for test circuit see Figure 13.
NXP Semiconductors 74LVC1G58
Low-power configurable multiple function gate
12. Waveforms
Table 10. Measurement points
NXP Semiconductors 74LVC1G58
Low-power configurable multiple function gate
13. Transfer characteristics
Table 11. Test data
Table 12. Transfer characteristicsAt recommended operating conditions; voltages are referenced to GND (ground = 0 V).
NXP Semiconductors 74LVC1G58
Low-power configurable multiple function gate[1] Typical values are measured at Tamb =25C.
14. Waveforms transfer characteristics
Table 12. Transfer characteristics …continuedAt recommended operating conditions; voltages are referenced to GND (ground = 0 V).
NXP Semiconductors 74LVC1G58
Low-power configurable multiple function gate
