74LV4052DB ,Dual 4-channel analog multiplexer/demultiplexerapplications: 1.0 to 6.0 Vfunction compatible with the 74HC/HCT4052.• Accepts TTL input levels betw ..
74LV4052PW ,Dual 4-channel analog multiplexer/demultiplexerINTEGRATED CIRCUITS74LV4052Dual 4-channel analogmultiplexer/demultiplexerProduct specification 1998 ..
74LV4053 ,Triple 2-channel analog multiplexer/demultiplexer
74LV4053A , TRIPLE 2-CHANNEL ANALOG MULTIPLEXERS/DEMULTIPLEXERS
74LV4053D ,Triple 2-channel analog multiplexer/demultiplexer74LV4053Triple single-pole double-throw analog switchRev. 04 — 10 August 2009 Product data sheet1.
74LV4053DB ,Triple 2-channel analog multiplexer/demultiplexerFeaturesn Optimized for low-voltage
7WBD3125USG , 2-Bit Translating Bus Switch
8.192 , 64-Pin 8-Bit Flash Microcontroller Product Brief
8.192 , 64-Pin 8-Bit Flash Microcontroller Product Brief
80021012A ,Octal Bus Transceivers With 3-State OutputsLogic Diagram (Positive Logic)1DIR19OE2A118B1To Seven Other ChannelsCopyright 2016, Texas Instrume ..
8035AHL , HMOS SINGLE-COMPONENT 8-BIT MICROCONTROLLER
8041-05-011 , DIP Reed Relays
74LV4052D-74LV4052DB-74LV4052PW
Dual 4-channel analog multiplexer/demultiplexer
Product specification
Supersedes data of 1997 Jul 15
IC24 Data Handbook
1998 Jun 23
Philips Semiconductors Product specification
74LV4052Dual 4-channel analog multiplexer/demultiplexer
FEATURES Optimized for low voltage applications: 1.0 to 6.0 V Accepts TTL input levels between VCC = 2.7 V and VCC = 3.6 V Low typ “ON” resistance:
60 at Vcc – VEE = 4.5 V
90 at Vcc – VEE = 3.0 V
145 at Vcc – VEE = 2.0 V Logic level translation: to enable 3 V logic to communicate with ± 3
V analog signals Typical “break before make” built in Analog/Digital multiplexing and demultiplexing Signal gating Output capability: non-standard ICC category: MSI
DESCRIPTIONThe 74LV4052 is a low-voltage CMOS device and is pin and
function compatible with the 74HC/HCT4052.
The 74LV4052 is a dual 4-channel analog multiplexer/demultiplexer
with a common select logic. Each multiplexer has four independent
inputs/outputs (nY0 to nY3) and a common input/output (nZ). The
common channel select logics include two digital select inputs (S0
and S1) and an active LOW enable input (E).
With E LOW, one of the four switches is selected (low impedance
ON-state) by S0 and S1. With E HIGH, all switches are in the high
impedance OFF-state, independent of S0 and S1. VCC and GND are
the supply voltage pins for the digital control inputs (S0, S1 and E).
The VCC to GND ranges are 1.0 to 6.0 V. The analog inputs/outputs
(nY0, to nY3, and nZ) can swing between VCC as a positive limit and
VEE as a negative limit. VCC - VEE may not exceed 6.0 V. For
operation as a digital multiplexer/demultiplexer, VEE is connected to
GND (typically ground).
QUICK REFERENCE DATAGND = 0 V; Tamb = 25°C; tr =tf ≤ 2.5 ns
NOTES: CPD is used to determine the dynamic power dissipation (PD in μW)
PD = CPD × VCC 2 × fi ((CL + CS) × VCC 2 × fo) where:
fi = input frequency in MHz; CL = output load capacity in pF;
fo = output frequency in MHz; CS = maximum switch capacitance in pF;
VCC = supply voltage in V; ((CL +CS) × VCC2 × fo) = sum of the outputs. The condition is VI = GND to VCC.
ORDERING INFORMATION
PIN CONFIGURATION
PIN DESCRIPTION
Philips Semiconductors Product specification
74LV4052Dual 4-channel analog multiplexer/demultiplexer
LOGIC SYMBOL
FUNCTION TABLE
NOTES:H= HIGH voltage levelL= LOW voltage levelX= don’t care
LOGIC SYMBOL (IEEE/IEC)
Philips Semiconductors Product specification
74LV4052Dual 4-channel analog multiplexer/demultiplexer
FUNCTIONAL DIAGRAM
SCHEMATIC DIAGRAM (ONE SWITCH)
Philips Semiconductors Product specification
74LV4052Dual 4-channel analog multiplexer/demultiplexer
ABSOLUTE MAXIMUM RATINGS1, 2In accordance with the Absolute Maximum Rating System (IEC 134).
Voltages are referenced to GND (ground = 0 V).
NOTES: Stresses beyond those listed may cause permanent damage to the device. These are stress ratings only and functional operation of the
device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to
absolute-maximum-rated conditions for extended periods may affect device reliability. The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
RECOMMENDED OPERATING CONDITIONS
NOTE: The LV is guaranteed to function down to VCC = 1.0V (input levels GND or VCC); DC characteristics are guaranteed from VCC = 1.2V to VCC = 6.0V.
Philips Semiconductors Product specification
74LV4052Dual 4-channel analog multiplexer/demultiplexer
DC ELECTRICAL CHARACTERISTICSOver recommended operating conditions, voltages are referenced to GND (ground = 0 V)
NOTES: All typical values are measured at Tamb = 25°C. At supply voltages approaching 1.2 V, the analog switch ON-resistance becomes extremely non-linear. Therefore, it is recommended that
these devices be used to transmit digital signals only, when using these supply voltages. RON (MAX) data is preliminary.
Philips Semiconductors Product specification
74LV4052Dual 4-channel analog multiplexer/demultiplexer
DC ELECTRICAL CHARACTERISTICS (Continued)
NOTES: All typical values are measured at Tamb = 25°C. At supply voltages approaching 1.2 V, the analog switch ON-resistance becomes extremely non-linear. Therefore, it is recommended that
these devices be used to transmit digital signals only, when using these supply voltages. RON (MAX) data is preliminary.
Figure 1. Test circuit for measuring ON-resistance (RON).ÎÎÎ
Figure 2. Test circuit for measuring OFF-state current.
Figure 3. Test circuit for measuring ON-state current.
Figure 4. Typical ON-resistance (Ron) as a function of input
voltage (Vis) for Vis = 0 to VCC – VEE.
Philips Semiconductors Product specification
74LV4052Dual 4-channel analog multiplexer/demultiplexer
Figure 5. Guaranteed operating area as a
function of the supply voltages.
AC CHARACTERISTICSGND = 0 V; tr = tf ≤ 2.5ns; CL = 50pF
NOTES: Unless otherwise stated, all typical values are measured at Tamb = 25°C Typical values are measured at VCC = 3.3 V.
