![](/IMAGES/ls12.gif)
74HCU04D ,Hex inverterPin configuration DIP14, SO14 and (T)SSOP14 Fig 5.
74HCU04DB ,Hex inverterPin configuration DHVQFN1474HCU04 All information provided in this document is subject to legal dis ..
74HCU04N ,Hex inverterLogic diagram (one inverter)5. Pinning information 74HCU04terminal 1index area74HCU041Y 2 13 6A1 14 ..
74HCU04PW ,74HCU04; Hex inverterGENERAL DESCRIPTIONThe 74HCU04 is a high-speed Si-gate CMOS device and is pin compatible with low p ..
74HCU04PW ,74HCU04; Hex inverterFEATURES• Output capability: standard• I category: SSICC
74HCU04PW ,74HCU04; Hex inverterGeneral descriptionThe 74HCU04 is a hex unbuffered inverter. Inputs include clamp diodes. This enab ..
7555IBA , General Purpose Timers
7555IBA , General Purpose Timers
7555IBAZ , General Purpose Timers
7555IPA , General Purpose Timers
7555IPA , General Purpose Timers
7555IPA , General Purpose Timers
74HCU04D-74HCU04DB-74HCU04N-74HCU04PW
Hex inverter
1. General descriptionThe 74HCU04 is a hex unbuffered inverter. Inputs include clamp diodes. This enables the
use of current limiting resistors to interface inputs to voltages in excess of VCC.
2. Features and benefits Complies with JEDEC standard JESD7A Balanced propagation delays ESD protection: HBM JESD22-A114F exceeds 2000V MM JESD22-A115-A exceeds 200V Multiple package options Specified from 40 Cto +125 C
3. Ordering information
74HCU04
Hex inverter
Rev. 6 — 27 December 2012 Product data sheet
Table 1. Ordering information74HCU04N 40 C to +125C DIP14 plastic dual in-line package; 14 leads (300 mil) SOT27-1
74HCU04D 40 C to +125C SO14 plastic small outline package; 14 leads; body width 3.9 mm SOT108-1
74HCU04DB 40 C to +125C SSOP14 plastic shrink small outline package; 14 leads; body width 5.3 mm SOT337-1
74HCU04PW 40 C to +125C TSSOP14 plastic thin shrink small outline package; 14 leads;
body width4.4 mm
SOT402-1
74HCU04BQ 40 C to +125C DHVQFN14 plastic dual in-line compatible thermal enhanced very thin
quad flat package; no leads; 14 terminals; body 2.53 0.85 mm
SOT762-1
NXP Semiconductors 74HCU04
Hex inverter
4. Functional diagram
5. Pinning informationNXP Semiconductors 74HCU04
Hex inverter
5.1 Pin description
6. Functional description
7. Limiting values
Table 2. Pin description 1 data input 2 data output 3 data input 4 data output 5 data input 6 data output
GND 7 ground (0 V) 8 data output 9 data input 10 data output 11 data input 12 data output 13 data input
VCC 14 supply voltage
Table 3. Function tableH = HIGH voltage level; L = LOW voltage level
Table 4. Limiting valuesIn accordance with the Absolute Maximum Rating System (IEC 60134).
VCC supply voltage 0.5 +7.0 V
IIK input clamping current VI < 0.5 V orVI >VCC +0.5V [1]- 20 mA
IOK output clamping current VO< 0.5 V orVO >VCC +0.5V [1]- 50 mA output current 0.5 V < VO < VCC +0.5V - 25 mA
ICC supply current - 50 mA
IGND ground current 50 - mA
Tstg storage temperature 65 +150 C
Ptot total power dissipation [2]
DIP14 package - 750 mW
SO14, (T)SSOP14 and
DHVQFN14 packages 500 mW
NXP Semiconductors 74HCU04
Hex inverter[1] The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
[2] For DIP14 package: Ptot derates linearly with 12 mW/K above 70 C.
For SO14 package: Ptot derates linearly with 8 mW/K above 70 C.
For (T)SSOP14 packages: Ptot derates linearly with 5.5 mW/K above 60C.
For DHVQFN14 packages: Ptot derates linearly with 4.5 mW/K above 60C.
8. Recommended operating conditions
9. Static characteristics
Table 5. Recommended operating conditionsVoltages are referenced to GND (ground = 0 V).
VCC supply voltage 2.0 5.0 6.0 V input voltage 0 - VCC V output voltage 0 - VCC V
Tamb ambient temperature 40 +25 +125 C
Table 6. Static characteristicsVoltages are referenced to GND (ground = 0 V).
VIH HIGH-level
input voltage
VCC = 2.0 V 1.7 1.4 - 1.7 - 1.7 - V
VCC = 3.0 V 3.6 2.6 - 3.6 - 3.6 - V
VCC = 5.5 V 4.8 3.4 - 4.8 - 4.8 - V
VIL LOW-level
input voltage
VCC = 2.0 V - 0.6 0.3 - 0.3 - 0.3 V
VCC = 3.0 V - 1.9 0.9 - 0.9 - 0.9 V
VCC = 5.5 V - 2.6 1.2 - 1.2 - 1.2 V
VOH HIGH-level
output voltage = VIH or VIL = 20 A; VCC= 2.0V 1.8 2.0 - 1.8 - 1.8 - V = 20 A; VCC= 4.5V 4.0 4.5 - 4.0 - 4.0 - V = 4.0 mA; VCC= 4.5V 3.98 4.32- 3.84 - 3.7 - V = 20 A; VCC= 6.0V 5.5 6.0 - 5.5 - 5.5 - V = 5.2 mA; VCC= 6.0V 5.48 5.81- 5.34 - 5.2 - V
VOL LOW-level
output voltage = VIH or VIL = 20 A; VCC= 2.0V - 0 0.2 - 0.2 - 0.2 V = 20 A; VCC= 4.5V - 0 0.5 - 0.5 - 0.5 V = 4.0 mA; VCC= 4.5V - 0.15 0.26- 0.33 - 0.4 V = 20 A; VCC= 6.0V - 0 0.5 - 0.5 - 0.5 V = 5.2 mA; VCC= 6.0V - 0.16 0.26- 0.33 - 0.4 V
NXP Semiconductors 74HCU04
Hex inverter
10. Dynamic characteristics[1] tpd is the same as tPHL, tPLH.
[2] tt is the same as tTHL, tTLH.
[3] CPD is used to determine the dynamic power dissipation (PD in W). =CPD VCC2fi N+ (CL VCC2fo) where:= input frequency in MHz;= output frequency in MHz;= output load capacitance in pF;
VCC= supply voltage in V;= number of inputs switching;
(CL VCC2 fo) = sum of outputs. input leakage
current =VCCor GND;
VCC =6.0V 0.1 - 1.0 - 1.0 A
ICC supply current VI =VCCor GND; IO =0A;
VCC =6.0V
--2 - 20 - 20 A input
capacitance
-3.5- - - - - pF
Table 6. Static characteristics …continuedVoltages are referenced to GND (ground = 0 V).
Table 7. Dynamic characteristicsVoltages are referenced to GND (ground=0 V); For test circuit see Figure7.
tpd propagation delay nA to nY; see Figure6 [1]
VCC = 2.0 V; CL = 50 pF 19 70 90 105 ns
VCC = 4.5 V; CL = 50 pF 7 14 18 21 ns
VCC = 5.0 V; CL = 15 pF 5 - - - ns
VCC = 6.0 V; CL = 50 pF 6 12 15 18 ns transition time see Figure6 [2]
VCC = 2.0 V; CL = 50 pF 19 75 95 110 ns
VCC = 4.5 V; CL = 50 pF 7 15 19 22 ns
VCC = 6.0 V; CL = 50 pF 6 13 16 19 ns
CPD power dissipation
capacitance
per inverter; VI =GNDto VCC [3] 10 - pF
NXP Semiconductors 74HCU04
Hex inverter
11. Waveforms
12. Typical transfer characteristicsNXP Semiconductors 74HCU04
Hex inverterNXP Semiconductors 74HCU04
Hex inverter
13. Application informationSome applications are:
Linear amplifier (see Figure 13)
Crystal oscillator design (see Figure 14)
Astable multivibrator (see Figure 15)
Remark: All values given are typical unless otherwise specified.
Table 8. External components for resonator (f<1 MHz)All values given are typical and must be used as an initial set-up. kHz to 15.9 kHz 22 M 220 k 56 pF 20 pF kHz to 24.9 kHz 22 M 220 k 56 pF 10 pF kHz to 54.9 kHz 22 M 100 k 56 pF 10 pF kHz to 129.9 kHz 22 M 100 k 47 pF 5 pF
130 kHz to 199.9 kHz 22 M 47 k 47 pF 5 pF
200 kHz to 349.9 kHz 10 M 47 k 47 pF 5 pF
350 kHz to 600 kHz 10 M 47 k 47 pF 5 pF
NXP Semiconductors 74HCU04
Hex inverter
Table 9. Optimum value for R2 kHz 2.0 k minimum required ICC
8.0 k minimum influence due to change in VCC kHz 1.0 k minimum required ICC
4.7 k minimum influence by VCC
10 kHz 0.5 k minimum required ICC
2.0 k minimum influence by VCC
14 kHz 0.5 k minimum required ICC
1.0 k minimum influence by VCC
>14 kHz - replace R2 by C3 with a typical value of 35pF