74HC4060PW Fast Delivery |IC PHOENIX CO.,LIMITED

74HC4060PW ,74HC/HCT4060; 14-stage binary ripple counter with oscillatorGeneral descriptionThe 74HC4060; 74HCT4060 are high-speed Si-gate CMOS device and is pin compatible ..
74HC4060PW ,74HC/HCT4060; 14-stage binary ripple counter with oscillatorFEATURES terminals (RS, R and C ), ten buffered outputs (Q toTC TC 3Q and Q to Q ) and an overridin ..
74HC4066BQ ,Quad single-pole single-throw analog switchINTEGRATED CIRCUITSDATA SHEET74HC4066; 74HCT4066Quad bilateral switchesProduct speciﬁcation 2004 No ..
74HC4066D ,Quad single-pole single-throw analog switchPin configuration for DIP14, SO14, SSOP14 Fig 5.
74HC4066DB ,74HC4066; 74HCT4066; Quad bilateral switchesGENERAL DESCRIPTION• Very low ON-resistance: The 74HC4066 and 74HCT4066 are high-speed Si-gateCMOS ..
74HC4066N ,74HC4066; 74HCT4066; Quad bilateral switchesGENERAL DESCRIPTION• Very low ON-resistance: The 74HC4066 and 74HCT4066 are high-speed Si-gateCMOS ..
74LVTH16501DGGRE4 ,3.3-V ABT 18-Bit Universal Bus Transceivers With 3-State Outputs 56-TSSOP -40 to 85/sc/package.Please be aware that an important notice concerning availability, standard warranty, an ..
74LVTH16501MEAX ,Low Voltage 18-Bit Universal Bus Transceivers with 3-STATE Outputsapplications, but with the capability to provide a TTL inter-Human-Body Model > 2000Vface to a 5V e ..
74LVTH16501MTD ,Low Voltage 18-Bit Universal Bus Transceivers with 3-STATE OutputsFeaturesThe LVTH16501 is an 18-bit universal bus transceiver

74HC4060PW
14-stage binary ripple counter with oscillator
General descriptionThe 74HC4060; 74HCT4060 are high-speed Si-gate CMOS device and is pin compatible
with the HEF4060.
The 74HC4060; 74HCT4060 are 14-stage ripple-carry counter/dividers and oscillators
with three oscillator terminals (RS, RTC and CTC), ten buffered outputs (Q3 to Q9 and
Q11 to Q13) and an overriding asynchronous master reset (MR). The oscillator
conﬁguration allows designof either RCor crystal oscillator circuits. The oscillator maybe
replacedbyan external clock signalat input RS.In this case keep the other oscillator pins
(RTC and CTC) ﬂoating. The counter advances on the negative-going transition of RS. A
HIGH levelon MR resets the counter (Q3to Q9 and Q11to Q13= LOW), independentof
other input conditions. In the HCT version, the MR input is TTL compatible, but the RS
input has CMOS input switching levels and can be driven by a TTL output by using a
pull-up resistor to VCC. Features All active components on chip RC or crystal oscillator conﬁguration Complies with JEDEC standard no. 7 A ESD protection: HBM JESD22-A114E exceeds 2000V MM JESD22-A115-A exceeds 200V Multiple package options Speciﬁed from −40 °Cto+85 °C and from −40°Cto +125°C Applications Control counters Timers Frequency dividers Time-delay circuits
74HC4060; 74HCT4060
14-stage binary ripple counter with oscillator
Rev. 03 — 14 July 2008 Product data sheet
NXP Semiconductors 74HC4060; 74HCT4060
14-stage binary ripple counter with oscillator Ordering information Functional diagram
Table 1. Ordering information
74HC4060N −40 °C to +125°C DIP16 plastic dual in-line package; 16 leads (300 mil) SOT38-4
74HCT4060N
74HC4060D −40 °C to +125°C SO16 plastic small outline package; 16 leads;
body width 3.9 mm
SOT109-1
74HCT4060D
74HC4060DB −40 °C to +125°C SSOP16 plastic shrink small outline package; 16 leads;
body width 5.3 mm
SOT338-1
74HCT4060DB
74HC4060PW −40°Cto +125°C TSSOP16 plastic thin shrink small outline package; 16 leads;
body width 4.4 mm
SOT403-1
74HC4060BQ −40°Cto +125°C DHVQFN16 plastic dual in-line compatible thermal-enhanced
very thin quadﬂat package;no leads;16 terminals;
body 2.5× 3.5 × 0.85 mm
SOT763-1
74HCT4060BQ
NXP Semiconductors 74HC4060; 74HCT4060
14-stage binary ripple counter with oscillator
NXP Semiconductors 74HC4060; 74HCT4060
14-stage binary ripple counter with oscillator Pinning information
6.1 Pinning
6.2 Pin description
Table 2. Pin description
Q11 to Q13 1, 2, 3 counter output
Q3 to Q9 7, 5, 4, 6, 14, 13, 15 counter output
GND 8 ground (0V)
CTC 9 external capacitor connection
RTC 10 external resistor connection 11 clock input /oscillator pin 12 master reset input (active HIGH)
VCC 16 supply voltage
NXP Semiconductors 74HC4060; 74HCT4060
14-stage binary ripple counter with oscillator Functional description Limiting values
Table 3. Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
VCC supply voltage −0.5 +7 V
IIK input clamping current VI < −0.5 V or VI >VCC+ 0.5 V [1]- ±20 mA
IOK output clamping current VO< −0.5 V or VO >VCC+ 0.5V [1]- ±20 mA output current −0.5 V < VO < VCC+ 0.5V - ±25 mA
ICC supply current - 50 mA
IGND ground current −50 - mA
Tstg storage temperature −65 +150 °C
NXP Semiconductors 74HC4060; 74HCT4060
14-stage binary ripple counter with oscillator
[1] The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
[2] Ptot derates linearly with 12 mW/K above 70°C.
[3] Ptot derates linearly with 8 mW/K above 70°C.
[4] Ptot derates linearly with 5.5 mW/K above 60°C.
[5] Ptot derates linearly with 4.5 mW/K above 60°C. Recommended operating conditions
10. Static characteristics
Ptot total power dissipation Tamb = −40 °C to +125°C
DIP16 package [2]- 750 mW
SO16 package [3]- 500 mW
(T)SSOP16 package [4]- 500 mW
DHVQFN16 package [5]- 500 mW
Table 3. Limiting values …continued
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
Table 4. Recommended operating conditions
Voltages are referenced to GND (ground = 0V)
VCC supply voltage 2.0 5.0 6.0 4.5 5.0 5.5 V input voltage 0 - VCC 0- VCC V output voltage 0 - VCC 0- VCC V
Tamb ambient temperature −40 - +125 −40 - +125 °C
Δt/ΔV input transition rise and fall rate VCC = 2.0 V - - 625 - - - ns/V
VCC = 4.5 V - 1.67 139 - 1.67 139 ns/V
VCC = 6.0 V - - 83 - - - ns/V
Table 5. Static characteristics
At recommended operating conditions; voltages are referenced to GND (ground=0V).
74HC4060
VIH HIGH-level
input voltage
MR input
VCC = 2.0 V 1.5 1.3 - 1.5 - 1.5 - V
VCC = 4.5 V 3.15 2.4 - 3.15 - 3.15 - V
VCC = 6.0 V 4.2 3.1 - 4.2 - 4.2 - V
RS input
VCC = 2.0 V 1.7 - - 1.7 - 1.7 - V
VCC = 4.5 V 3.6 - - 3.6 - 3.6 - V
VCC = 6.0 V 4.8 - - 4.8 - 4.8 - V
NXP Semiconductors 74HC4060; 74HCT4060
14-stage binary ripple counter with oscillator
VIL LOW-level
input voltage
MR input
VCC = 2.0 V - 0.8 0.5 - 0.5 - 0.5 V
VCC = 4.5 V - 2.1 1.35 - 1.35 - 1.35 V
VCC = 6.0 V - 2.8 1.8 - 1.8 - 1.8 V
RS input
VCC = 2.0 V - - 0.3 - 0.3 - 0.3 V
VCC = 4.5 V - - 0.9 - 0.9 - 0.9 V
VCC = 6.0 V - - 1.2 - 1.2 - 1.2 V
VOH HIGH-level
output
voltage
RTC output; RS= MR= GND= −20 μA; VCC= 2.0V 1.9 2.0 - 1.9 - 1.9 - V= −20 μA; VCC= 4.5V 4.4 4.5 - 4.4 - 4.4 - V= −20 μA; VCC= 6.0V 5.9 6.0 - 5.9 - 5.9 - V= −2.6 mA; VCC= 4.5V 3.98 - - 3.84 - 3.7 - V= −3.3 mA; VCC= 6.0V 5.48 - - 5.34 - 5.2 - V
RTC output; RS = MR = VCC= −20 μA; VCC= 2.0V 1.9 2.0 - 1.9 - 1.9 - V= −20 μA; VCC= 4.5V 4.4 4.5 - 4.4 - 4.4 - V= −20 μA; VCC= 6.0V 5.9 6.0 - 5.9 - 5.9 - V= −0.65 mA; VCC= 4.5V 3.98 - - 3.84 - 3.7 - V= −0.85 mA; VCC= 6.0V 5.48 - - 5.34 - 5.2 - V
CTC output;
RS=VIH;MR=VIL= −3.2 mA; VCC= 4.5V 3.98 - - 3.84 - 3.7 - V= −4.2 mA; VCC= 6.0V 5.48 - - 5.34 - 5.2 - V =VIHor VIL;
except RTC output= −20 μA; VCC= 2.0V 1.9 2.0 - 1.9 - 1.9 - V= −20 μA; VCC= 4.5V 4.4 4.5 - 4.4 - 4.4 - V= −20 μA; VCC= 6.0V 5.9 6.0 - 5.9 - 5.9 - V =VIHor VIL;
except RTC and CTC outputs= −4.0 mA; VCC= 4.5V 3.98 - - 3.84 - 3.7 - V= −5.2 mA; VCC= 6.0V 5.48 - - 5.34 - 5.2 - V
Table 5. Static characteristics …continued
At recommended operating conditions; voltages are referenced to GND (ground=0V).
NXP Semiconductors 74HC4060; 74HCT4060
14-stage binary ripple counter with oscillator
VOL LOW-level
output
voltage
RTC output; RS = VCC;= GND =20 μA; VCC= 2.0V - 0 0.1 - 0.1 - 0.1 V =20 μA; VCC= 4.5V - 0 0.1 - 0.1 - 0.1 V =20 μA; VCC= 6.0V - 0 0.1 - 0.1 - 0.1 V= 2.6 mA; VCC= 4.5V - - 0.26 - 0.33 - 0.4 V= 3.3 mA; VCC= 6.0V - - 0.26 - 0.33 - 0.4 V
CTC output; RS = VIL;= VIH= 3.2 mA; VCC= 4.5V - - 0.26 - 0.33 - 0.4 V= 4.2 mA; VCC= 6.0V - - 0.26 - 0.33 - 0.4 V =VIHor VIL;
except RTC output =20 μA; VCC= 2.0V - 0 0.1 - 0.1 - 0.1 V =20 μA; VCC= 4.5V - 0 0.1 - 0.1 - 0.1 V =20 μA; VCC= 6.0V - 0 0.1 - 0.1 - 0.1 V =VIHor VIL;
except RTC and CTC outputs= 4.0 mA; VCC= 4.5V - - 0.26 - 0.33 - 0.4 V= 5.2 mA; VCC= 6.0V - - 0.26 - 0.33 - 0.4 V input leakage
current =VCCor GND; VCC= 6.0V - - ±0.1 - ±1.0 - ±1.0 μA
ICC supply
current =VCCor GND; IO =0A;
VCC= 6.0V - 8.0 - 80 - 160 μA input
capacitance 3.5 - - - - - pF
74HCT4060
VIH HIGH-level
input voltage
MR input;
VCC= 4.5Vto 5.5V
[1] 2.0 - - 2.0 - 2.0 - V
VIL LOW-level
input voltage
MR input;
VCC= 4.5Vto 5.5V
[1] - - 0.8 - 0.8 - 0.8 V
Table 5. Static characteristics …continued
At recommended operating conditions; voltages are referenced to GND (ground=0V).
NXP Semiconductors 74HC4060; 74HCT4060
14-stage binary ripple counter with oscillator
[1] For HCT4060, only input MR (pin 12) has TTL input switching levels.
VOH HIGH-level
output
voltage
RTC output; RS = MR = VCC= −20 μA; VCC= 4.5V 4.4 4.5 - 4.4 - 4.4 - V= −0.65 mA; VCC= 4.5V 3.98 - - 3.84 - 3.7 - V
RTC output; RS= MR= GND= −20 μA; VCC= 4.5V 4.4 4.5 - 4.4 - 4.4 - V= −2.6 mA; VCC= 4.5V 3.98 - - 3.84 - 3.7 - V
CTC output; RS= VIH;=VIL= −3.2 mA; VCC= 4.5V 3.98 - - 3.84 - 3.7 - V =VIHor VIL;
except RTC output= −20 μA; VCC= 4.5V 4.4 4.5 - 4.4 - 4.4 - V =VIHor VIL;
except RTC and CTC outputs= −4.0 mA; VCC= 4.5V 3.98 - - 3.84 - 3.7 - V
VOL LOW-level
output
voltage
RTC output; RS = VCC;= GND =20 μA; VCC= 4.5V - 0 0.1 - 0.1 - 0.1 V= 2.6 mA; VCC= 4.5V - - 0.26 - 0.33 - 0.4 V
CTC output; RS = VIL;= VIH= 3.2 mA; VCC= 4.5V - - 0.26 - 0.33 - 0.4 V =VIHor VIL;
except RTC output =20 μA; VCC= 4.5V - 0 0.1 - 0.1 - 0.1 V =VIHor VIL;
except RTC and CTC outputs= 4.0 mA; VCC= 4.5V - - 0.26 - 0.33 - 0.4 V input leakage
current =VCCor GND; VCC= 5.5V - - ±0.1 - ±1.0 - ±1.0 μA
ICC supply
current =VCCor GND;
VCC= 5.5 V; IO =0A - 8.0 - 80 - 160 μA
ΔICC additional
supply
current
per input pin; =VCC− 2.1V; other inputs
at VCCor GND;
VCC= 4.5Vto 5.5 V; IO =0A 40 144 - 180 - 196 μA input
capacitance 3.5 - - - - - pF
Table 5. Static characteristics …continued
At recommended operating conditions; voltages are referenced to GND (ground=0V).
NXP Semiconductors 74HC4060; 74HCT4060
14-stage binary ripple counter with oscillator
11. Dynamic characteristics
Table 6. Dynamic characteristics
GND = 0 V; CL = 50 pF unless otherwise speciﬁed; for test circuit see Figure 11.
74HC4060
tpd propagation
delay
RS to Q3; see Figure8 [1]
VCC = 2.0 V - 99 300 - 375 - 450 ns
VCC = 4.5 V - 36 60 - 75 - 90 ns
VCC = 5.0 V; CL =15pF - 31 - - - - - ns
VCC = 6.0 V - 29 51 - 64 - 77 ns
Qn to Qn+1; see Figure9 [2]
VCC = 2.0 V - 22 80 - 100 - 120 ns
VCC = 4.5 V - 8 16 - 20 - 24 ns
VCC = 5.0 V; CL =15pF - 6 - - - - - ns
VCC = 6.0 V - 6 14 - 17 - 20 ns
tPHL HIGHto LOW
propagation
delay
MR to Qn; see Figure10
VCC = 2.0 V - 55 175 - 220 - 265 ns
VCC = 4.5 V - 20 35 - 44 - 53 ns
VCC = 5.0 V; CL =15pF - 17 - - - - - ns
VCC = 6.0 V - 16 30 - 37 - 45 ns transition time Qn; see Figure8 [3]
VCC = 2.0 V - 19 75 - 95 - 110 ns
VCC = 4.5 V - 7 15 - 19 - 22 ns
VCC = 6.0 V - 6 13 - 16 - 19 ns pulse width RS (HIGH or LOW);
see Figure8
VCC = 2.0 V 80 17 - 100 - 120 - ns
VCC = 4.5 V 16 6 - 20 - 24 - ns
VCC = 6.0 V 14 5 - 17 - 20 - ns
MR (HIGH); see Figure10
VCC = 2.0 V 80 25 - 100 - 120 - ns
VCC = 4.5 V 16 9 - 20 - 24 - ns
VCC = 6.0 V 14 7 - 17 - 20 - ns
trec recovery time MRto RS; see Figure10
VCC = 2.0 V 100 28 - 125 - 150 - ns
VCC = 4.5 V 20 10 - 25 - 30 - ns
VCC = 6.0 V 17 8 - 21 - 26 - ns
NXP Semiconductors 74HC4060; 74HCT4060
14-stage binary ripple counter with oscillator
fmax maximum
frequency
RS; see Figure8
VCC = 2.0 V 6 26 - 4.8 - 4 - MHz
VCC = 4.5 V 30 80 - 24 - 20 - MHz
VCC = 5.0 V; CL=15pF - 87 - - - - - MHz
VCC = 6.0 V 35 95 - 28 - 24 - MHz
CPD power
dissipation
capacitance
VI = GND to VCC;
VCC =5V; fi=1 MHz
[4] -40 - - - - - pF
74HCT4060
tpd propagation
delay
RS to Q3; see Figure8 [1]
VCC = 4.5 V - 33 66 - 83 - 99 ns
VCC = 5.0 V; CL =15pF - 31 - - - - - ns
Qn to Qn+1; see Figure9 [2]
VCC = 4.5 V - 8 16 - 20 - 24 ns
VCC = 5.0 V; CL =15pF - 6 - - - - - ns
tPHL HIGHto LOW
propagation
delay
MR to Qn; see Figure10
VCC = 4.5 V - 21 44 - 55 - 66 ns
VCC = 5.0 V; CL =15pF - 18 - - - - - ns transition time Qn; see Figure8 [3]
VCC = 4.5 V - 7 15 - 19 - 22 ns pulse width RS (HIGH or LOW);
see Figure8
VCC = 4.5 V 16 6 - 20 - 24 - ns
MR (HIGH); see Figure10
VCC = 4.5 V 16 6 - 20 - 24 - ns
trec recovery time MR to RS; see Figure10
VCC = 4.5 V 26 13 - 33 - 39 - ns
fmax maximum
frequency
RS; see Figure8
VCC = 4.5 V 30 80 - 24 - 20 - MHz
VCC = 5.0 V; CL=15pF - 88 - - - - - MHz
Table 6. Dynamic characteristics …continued
GND = 0 V; CL = 50 pF unless otherwise speciﬁed; for test circuit see Figure 11.
NXP Semiconductors 74HC4060; 74HCT4060
14-stage binary ripple counter with oscillator
[1] tpd is the same as tPHL and tPLH.
[2] Qn+1 is the next Qn output.
[3] tt is the same as tTHL and tTLH.
[4] CPDis used to determine the dynamic power dissipation (PD in μW): =CPD× VCC2×fi× N+ ∑(CL× VCC2× fo) where:= input frequency in MHz;= output frequency in MHz;= output load capacitance in pF;
VCC= supply voltage in V;= number of inputs switching;
∑(CL× VCC2×fo)= sum of outputs.
12. Waveforms
CPD power
dissipation
capacitance
VI = GND to VCC− 1.5V;
VCC =5V; fi=1 MHz
[4] -40 - - - - - pF
Table 6. Dynamic characteristics …continued
GND = 0 V; CL = 50 pF unless otherwise speciﬁed; for test circuit see Figure 11.
NXP Semiconductors 74HC4060; 74HCT4060
14-stage binary ripple counter with oscillator
Table 7. Measurement points
74HC4060 0.5× VCC 0.5× VCC
74HCT4060 1.3V 1.3 V

Partno	Mfg	Dc	Qty	Available	Descript
74HC4060PW	NXP	N/a	4300	avai	74HC/HCT4060; 14-stage binary ripple counter with oscillator