74HC1G126GW ,Bus buffer/line driver; 3-statePin configuration. Fig.2 Logic symbol.outYinA241OEOEFig.3 IEC logic symbol. Fig.4
74HC1G14GV ,74HC1G14; 74HCT1G14; Inverting Schmitt-triggersFeatures and benefits Symmetrical output impedance High noise immunity Low power dissipation Ba ..
74HC1G14GW ,Inverting Schmitt triggerPin configuration7.2 Pin description Table 3. Pin descriptionSymbol Pin Descriptionn.c. 1 not conne ..
74HC1G32GV ,2-input OR gatePin configuration. Fig.2 Logic symbol.handbook, halfpageB1handbook, halfpage≥14Y2MNA165 AMNA166Fig ..
74HC1G32GW ,2-input OR gateFeaturesn Symmetrical output impedancen High noise immunityn Low power dissipationn Balanced propag ..
74HC1G66GV ,Single-pole single-throw analog switchPin configuration. Fig.2 Logic symbol.Yhandbook, halfpageE1handbook, halfpage121V V4 #CC CCX1MNA ..
74LVC1G11GW ,Single 3-input AND gateGeneral descriptionThe 74LVC1G11 provides a single 3-input AND gate.The input can be driven from ei ..
74LVC1G11W6-7 , SINGLE 3 INPUT POSITIVE AND GATE
74LVC1G11W6-7 , SINGLE 3 INPUT POSITIVE AND GATE
74LVC1G125DBVRE4 ,Single Bus Buffer Gate With 3-State Outputs 5-SOT-23 -40 to 125Maximum Ratings . 411 Power Supply Recommendations... 127.2 Handling Ratings. 412 Layout.... 127.3 ..
74LVC1G125FZ4-7 , SINGLE BUFFER GATE WITH 3-STATE OUTPUT
74LVC1G125GF ,Bus buffer/line driver; 3-stateLogic diagram74LVC1G125 All information provided in this document is subject to legal disclaimers. ..
74HC1G126GW
Bus buffer/line driver; 3-state
Philips Semiconductors Product specification
Bus buffer/line driver; 3-state 74HC1G126
74HCT1G126
FEATURES Wide operating voltage :
2.0to 6.0V Symmetrical output impedance High noise immunity Low power dissipation Balanced propagation delays Very small 5 pins package Output capability : bus driver
DESCRIPTIONThe 74HC1G/HCT1G126 is a
highspeed Si-gate CMOS device.
The 74HC1G/HCT1G126 provides
one non-inverting buffer/line driver
with 3-state output. The 3-state output
is controlled by the output enable
input (OE). A LOW at OE causes the
output as assume a high impedance
OFF-state.
The bus driver output currents are
equal compared to the
74HC/HCT126.
FUNCTION TABLEH = HIGH voltage level
L = LOW voltage level
X = Don’t care
Z = High impedance OFF state
QUICK REFERENCE DATAGND=0 V; Tamb=25 °C; tr=tf≤ 6.0ns
Notes CPD is used to determine the dynamic power dissipation (PDin μW). = CPD× VCC2×fi+∑ (CL× VCC2×fo) where: = input frequency in MHz; = output frequency in MHz;= output load capacitance in pF;
VCC= supply voltage in V; (CL× VCC2×fo) = sum of outputs. For HC1G the condition is VI = GND to VCC.
For HCT1G the condition is VI= GNDto VCC− 1.5V.
PIN DESCRIPTION
Philips Semiconductors Product specification
Bus buffer/line driver; 3-state 74HC1G126
74HCT1G126
ORDERING AND PACKAGE INFORMATION
Philips Semiconductors Product specification
Bus buffer/line driver; 3-state 74HC1G126
74HCT1G126
RECOMMENDED OPERATING CONDITIONS
ABSOLUTE MAXIMUM RATINGSLimiting values is accordance with the Absolute Maximum Rating System (IEC 134).
Voltages are referenced to GND (ground = 0 V)
Notes Stresses beyond those listed may cause permanent damage to the device. These are stress rating only and
functional operation of the device at these or any other conditions beyond those under ‘recommended operating
conditions’ is not implied. Exposure to absolute maximum rated conditions for extended periods may affect device
reliability. The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
Philips Semiconductors Product specification
Bus buffer/line driver; 3-state 74HC1G126
74HCT1G126
DC CHARACTERISTICS FOR THE 74HC1GOver recommended operating conditions.
Voltage are referenced to GND (ground=0V)
Note All typical values are measured at Tamb = 25 °C.
Philips Semiconductors Product specification
Bus buffer/line driver; 3-state 74HC1G126
74HCT1G126
DC CHARACTERISTICS FOR THE 74HCT1GOver recommended operating conditions.
Voltage are referenced to GND (ground=0V.)
Note All typical values are measured at Tamb = 25 °C.
