74HC1G08GV ,2-input AND gateFunctional descriptionTable 4. Function tableH = HIGH voltage level; L = LOW voltage levelInput Out ..
74HC1G08GV ,2-input AND gateFeaturesn Symmetrical output impedancen High noise immunityn Low power dissipationn Balanced propag ..
74HC1G08GV ,2-input AND gate
74HC1G08GW ,2-input AND gateLogic diagram6. Pinning information6.1 Pinning74HC1G0874HCT1G08BV 1 5CCA 2GND 3 4 Y001aaf102Fig 4. ..
74HC1G125GV ,74HC1G125; 74HCT1G125; Bus buffer/line drivers; 3-stateFeatures■ Wide supply voltage range from 2.0 V to 6.0 V■ Symmetrical output impedance■ High noise i ..
74HC1G125GW ,Bus buffer/line driver; 3-statePin configuration. Fig.2 Logic symbol.handbook, halfpageoutYinA2handbook, halfpage41OEOEMNA119MNA1 ..
74LVC1G08W5-7 , SINGLE 2 INPUT POSITIVE AND GATE
74LVC1G10DW-7 , SINGLE 3 INPUT POSITIVE NAND GATE
74LVC1G10FW4-7 , SINGLE 3 INPUT POSITIVE NAND GATE
74LVC1G10GW ,Single 3-input NAND gateFeatures and benefits Wide supply voltage range from 1.65 V to 5.5 V High noise immunity Complie ..
74LVC1G10W6-7 , SINGLE 3 INPUT POSITIVE NAND GATE
74LVC1G10W6-7 , SINGLE 3 INPUT POSITIVE NAND GATE
74HC1G08GV-74HC1G08GW-74HCT1G08GV-74HCT1G08GW
2-input AND gate
General description74HC1G08 and 74HCT1G08 are high-speed, Si-gate CMOS devices. They provide a
2-input AND function.
The HC device has CMOS input switching levels and supply voltage range 2 V to 6 V.
The HCT device has TTL input switching levels and supply voltage range 4.5 V to 5.5 V.
The standard output currents are half those of the 74HC08 and 74HCT08.
Features Symmetrical output impedance High noise immunity Low power dissipation Balanced propagation delays SOT353-1 and SOT753 package options
Ordering information Marking
74HC1G08; 74HCT1G08
2-input AND gate
Rev. 04 — 17 July 2007 Product data sheet
Table 1. Ordering information74HC1G08GW −40 °C to +125°C TSSOP5 plastic thin shrink small outline package; 5 leads;
body width 1.25 mm
SOT353-1
74HCT1G08GW
74HC1G08GV −40 °C to +125°C SC-74A plastic surface-mounted package; 5 leads SOT753
74HCT1G08GV
Table 2. Marking codes74HC1G08GW HE
74HCT1G08GW TE
74HC1G08GV H08
74HCT1G08GV T08
NXP Semiconductors 74HC1G08; 74HCT1G08
2-input AND gate Functional diagram Pinning information
6.1 Pinning
6.2 Pin description
Table 3. Pin description 1 data input 2 data input
GND 3 ground (0V) 4 data output
VCC 5 supply voltage
NXP Semiconductors 74HC1G08; 74HCT1G08
2-input AND gate Functional description Limiting values[1] The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
[2] Above 55 °C the value of Ptot derates linearly with 2.5 mW/K.
Recommended operating conditions
Table 4. Function table= HIGH voltage level; L= LOW voltage level
LLL L L
HHH
Table 5. Limiting valuesIn accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).[1]
VCC supply voltage −0.5 +7.0 V
IIK input clamping current VI < −0.5 V or VI >VCC + 0.5V - ±20 mA
IOK output clamping current VO< −0.5 V or VO >VCC + 0.5V - ±20 mA output current −0.5 V < VO
ICC supply current - 25 mA
IGND ground current −25 - mA
Tstg storage temperature −65 +150 °C
Ptot total power dissipation Tamb = −40°Cto +125°C [2]- 200 mW
Table 6. Recommended operating conditions
Voltages are referenced to GND (ground = 0 V).
VCC supply voltage 2.0 5.0 6.0 4.5 5.0 5.5 V input voltage 0 - VCC 0- VCC V output voltage 0 - VCC 0- VCC V
Tamb ambient temperature −40 +25 +125 −40 +25 +125 °C
Δt/ΔV input transition rise
and fall rate
VCC = 2.0 V - - 625 - - - ns/V
VCC = 4.5 V - - 139 - - 139 ns/V
VCC = 6.0 V - - 83 - - - ns/V
NXP Semiconductors 74HC1G08; 74HCT1G08
2-input AND gate
10. Static characteristics
Table 7. Static characteristics
Voltages are referenced to GND (ground = 0 V). All typical values are measured at Tamb =25 °C.
For type 74HC1G08
VIH HIGH-level input
voltage
VCC = 2.0 V 1.5 1.2 - 1.5 - V
VCC = 4.5 V 3.15 2.4 - 3.15 - V
VCC = 6.0 V 4.2 3.2 - 4.2 - V
VIL LOW-level input
voltage
VCC = 2.0 V - 0.8 0.5 - 0.5 V
VCC = 4.5 V - 2.1 1.35 - 1.35 V
VCC = 6.0 V - 2.8 1.8 - 1.8 V
VOH HIGH-level output
voltage = VIH or VIL= −20 μA; VCC= 2.0V 1.9 2.0 - 1.9 - V= −20 μA; VCC= 4.5V 4.4 4.5 - 4.4 - V= −20 μA; VCC= 6.0V 5.9 6.0 - 5.9 - V= −2.0 mA; VCC= 4.5V 4.13 4.32 - 3.7 - V= −2.6 mA; VCC= 6.0V 5.63 5.81 - 5.2 - V
VOL LOW-level output
voltage = VIH or VIL = 20 μA; VCC= 2.0V - 0 0.1 - 0.1 V = 20 μA; VCC= 4.5V - 0 0.1 - 0.1 V = 20 μA; VCC= 6.0V - 0 0.1 - 0.1 V = 2.0 mA; VCC= 4.5V - 0.15 0.33 - 0.4 V = 2.6 mA; VCC= 6.0V - 0.16 0.33 - 0.4 V input leakage current VI =VCCor GND; VCC= 6.0V - - 1.0 - 1.0 μA
ICC supply current VI =VCCor GND; IO =0A;
VCC= 6.0V - 10 - 20 μA input capacitance - 1.5 - - - pF
For type 74HCT1G08
VIH HIGH-level input
voltage
VCC = 4.5 V to 5.5 V 2.0 1.6 - 2.0 - V
VIL LOW-level input
voltage
VCC = 4.5 V to 5.5 V - 1.2 0.8 - 0.8 V
VOH HIGH-level output
voltage = VIH or VIL= −20 μA; VCC= 4.5V 4.4 4.5 - 4.4 - V= −2.0 mA; VCC= 4.5V 4.13 4.32 - 3.7 - V
VOL LOW-level output
voltage = VIH or VIL = 20 μA; VCC= 4.5V - 0 0.1 - 0.1 V = 2.0 mA; VCC= 4.5V - 0.15 0.33 - 0.4 V input leakage current VI =VCCor GND; VCC= 5.5V - - 1.0 - 1.0 μA
NXP Semiconductors 74HC1G08; 74HCT1G08
2-input AND gate
11. Dynamic characteristics
[1] tpd is the same as tPLH and tPHL.
[2] CPD is used to determine the dynamic power dissipation PD (μW). =CPD× VCC2×fi+∑(CL× VCC2×fo) where:= input frequency in MHz= output frequency in MHz= output load capacitance in pF
VCC= supply voltage in Volts(CL× VCC2× fo) = sum of outputs
ICC supply current VI =VCCor GND; IO =0A;
VCC= 5.5V - 10 - 20 μA
ΔICC additional supply
current
per input; VCC= 4.5Vto 5.5V; =VCC− 2.1 V; IO =0A - 500 - 850 μA input capacitance - 1.5 - - - pF
Table 7. Static characteristics …continued
Voltages are referenced to GND (ground = 0 V). All typical values are measured at Tamb =25 °C.
Table 8. Dynamic characteristics
GND = 0 V; tr = tf ≤ 6.0 ns; All typical values are measured at Tamb =25 °C. For test circuit see Figure6
For type 74HC1G08
tpd propagation delayA and B to Y; see Figure5 [1]
VCC = 2.0 V; CL=50pF - 25 115 - 135 ns
VCC = 4.5 V; CL =50pF - 9 23 - 27 ns
VCC = 5.0 V; CL =15pF - 7 - - - ns
VCC = 6.0 V; CL =50pF - 8 20 - 23 ns
CPD power dissipation
capacitance= GNDto VCC [2] -19- - - pF
For type 74HCT1G08
tpd propagation delayA and B to Y; see Figure5 [1]
VCC = 4.5 V; CL=50pF - 11 23 - 27 ns
VCC = 5.0 V; CL =15pF - 11 - - - ns
CPD power dissipation
capacitance= GNDto VCC− 1.5V [2] -21- - - pF
NXP Semiconductors 74HC1G08; 74HCT1G08
2-input AND gate
12. Waveforms
