SN74CBT16233DLR ,16-Bit 1-of-2 FET Multiplexer/Demultiplexer SN74CBT16233 16-BIT 1-OF-2 FET MULTIPLEXER/DEMULTIPLEXER SCDS010K – MAY 1995 – REVISED NOVEMBER 20 ..
SN74CBT16244CDGG , 16-BIT FET BUS SWITCH 5-V BUS SWITCH WITH-2-V UNDERSHOOT PROTECTION
SN74CBT16244DGGR ,16-Bit FET Bus Switch SN54CBT16244, SN74CBT16244 16-BIT FET BUS SWITCHES SCDS031I – MAY 1996 – REVISED OCTOBER 2000SN54C ..
SN74CBT16244DGGR ,16-Bit FET Bus Switch/sc/package.FUNCTION TABLE(each 4-bit bus switch)INPUT OUTPUTSOE A, BL A port = B portH DisconnectP ..
SN74CBT16244DGGR ,16-Bit FET Bus Switchmaximum ratings” may cause permanent damage to the device. These are stress ratings only, andfuncti ..
SN74CBT16244DGVR ,16-Bit FET Bus Switchmaximum ratings over operating free-air temperature range (unless otherwise noted)Supply voltage ra ..
SN74S00 ,Quad 2-input positive-NAND gates SDLS025D–DECEMBER 1983–REVISED MAY 20175 Pin Configuration and FunctionsSN5400 J, SN54xx00 J and W ..
SN74S00N ,Quad 2-input positive-NAND gatesPin Functions (continued)PINI/O DESCRIPTIONCDIP, CFP, SOIC, SO CFPNAME LCCCPDIP, SO, SSOP (SN74xx00 ..
SN74S00NSR , QUADRUPLE 2-INPUT POSITIVE-NAND GATES
SN74S00NSR , QUADRUPLE 2-INPUT POSITIVE-NAND GATES
SN74S02D ,Quad 2-input positive-NOR gates
SN74S03 ,QUADRUPLE 2-INPUT POSITIVE-NAND GATES WITH OPEN-COLLECTOR OUTPUTS
74CBT16233DGGRE4-SN74CBT16233-SN74CBT16233DGGR-SN74CBT16233DGVR-SN74CBT16233DL-SN74CBT16233DLR
16-Bit 1-of-2 FET Multiplexer/Demultiplexer 56-TSSOP -40 to 85
descriptionThe SN74CBT16233 is a 16-bit 1-of-2 FET
multiplexer/demultiplexer used in applications in
which two separate data paths must be
multiplexed onto, or demultiplexed from, a single
path. This device can be used for memory
interleaving, where two different banks of memory
need to be addressed simultaneously. The device
can be used as two 8-bit to 16-bit multiplexers or
as one 16-bit to 32-bit multiplexer.
Two select (SEL1 and SEL2) inputs control the
data flow. When the TEST inputs are asserted, the
A port is connected to both the B1 and the B2
ports. SEL1, SEL2, and the TEST inputs can be
driven with a 5-V CMOS, a 5-V TTL, or a
low-voltage TTL driver.
This device is designed so it does not have
through current when switching directions.
ORDERING INFORMATION Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines
are available at www.ti.com/sc/package.
4B1
4B2
6B1
6B2
8B1
8B2
GND
VCC
10B1
10B2
11A
12B1
12B2
13A
14B1
14B2
15A
16B1
16B2
TEST1
TEST2
3B1
3B2
5B1
5B2
7B1
7B2
GND
VCC
9B1
9B2
10A
11B1
11B2
12A
13B1
13B2
14A
15B1
15B2
16A
SEL1
SEL2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
