74ALVC74PW ,Dual D-type flip-flop with set and reset; positive-edge triggerINTEGRATED CIRCUITSDATA SHEET74ALVC74Dual D-type flip-flop with set andreset; positive-edge trigger ..
74ALVCF162835 ,Low Voltage 18-Bit Universal Bus Driver with 3.6V Tolerant Outputs and 26-Ohm Series Resistors in Outputsapplications with I/O capability up to 3.6V.CCThe 74ALVCF162835 is fabricated with an advancedCMOS ..
74ALVCF322835 ,Low Voltage 36-Bit Universal Bus Driver with 3.6V Tolerant Outputs and 26-Ohm Series Resistors in OutputsFeaturesThe 74ALVCF322835 low voltage 36-bit universal bus
74ALVC74BQ-74ALVC74PW
Dual D-type flip-flop with set and reset; positive-edge trigger
Philips Semiconductors Product specification
Dual D-type flip-flop with set and reset;
positive-edge trigger 74ALVC74
FEATURES Wide supply voltage range from 1.65to 3.6V Complies with JEDEC standard:
JESD8-7 (1.65to 1.95V)
JESD8-5 (2.3to 2.7V)
JESD8B/JESD36 (2.7to 3.6 V). 3.6 V tolerant inputs/outputs CMOS low power consumption Direct interface with TTL levels (2.7to 3.6V) Power-down mode Latch-up performance exceeds 250 mA ESD protection:
HBM EIA/JESD22-A114-A exceeds 2000V
MM EIA/JESD22-A115-A exceeds 200V.
DESCRIPTIONThe 74ALVC74 is a dual positive-edge triggered, D-type
flip-flop with individual data (D), clock (CP), set (SD) and
reset (RD) inputs and complementary Q andQ outputs.
The set and reset are asynchronous active LOW inputs
and operate independently of the clock input. Information
on the data input is transferred to the Q output on the
LOW-to-HIGH transition of the clock pulse. The D inputs
mustbe stable one set-up time priorto the LOW-to-HIGH
clock transition for predictable operation.
Schmitt-trigger action in the clock input makes the circuit
highly tolerant to slower clock rise and fall times.
QUICK REFERENCE DATAGND=0 V; Tamb =25 °C.
Notes CPD is used to determine the dynamic power dissipation (PDin μW). =CPD× VCC2×fi× N+ Σ(CL× VCC2×fo) where:= input frequency in MHz;= output frequency in MHz;= output load capacitance in pF;
VCC= supply voltage in Volts;= total load switching outputs;
Σ(CL× VCC2×fo)= sum of the outputs. The condition is VI= GNDto VCC.
Philips Semiconductors Product specification
Dual D-type flip-flop with set and reset;
positive-edge trigger 74ALVC74
ORDERING INFORMATION
FUNCTION TABLES
Table 1 See note1
Table 2 See note1
Note H= HIGH voltage level;= LOW voltage level;= don’t care;= LOW-to-HIGH CP transition;
Qn+1= state after the next LOW-to-HIGH transition of CP.
Philips Semiconductors Product specification
Dual D-type flip-flop with set and reset;
positive-edge trigger 74ALVC74
PINNING
Philips Semiconductors Product specification
Dual D-type flip-flop with set and reset;
positive-edge trigger 74ALVC74
Philips Semiconductors Product specification
Dual D-type flip-flop with set and reset;
positive-edge trigger 74ALVC74
RECOMMENDED OPERATING CONDITIONS
LIMITING VALUES accordance with the Absolute Maximum Rating System (IEC 60134); voltages are referencedto GND (ground=0 V).
Notes The input and output voltage ratings may be exceeded if the input and output current ratings are observed. When VCC=0 V (Power-down mode), the output voltage can be 3.6 V in normal operation. For SO14 packages: above 70 °C the value of Ptot derates linearly with 8 mW/K.
For TSSOP14 packages: above 60 °C the value of Ptot derates linearly with 5.5 mW/K.
For DHVQFN14 packages: above 60 °C the value of Ptot derates linearly with 4.5 mW/K.
Philips Semiconductors Product specification
Dual D-type flip-flop with set and reset;
positive-edge trigger 74ALVC74
CHARACTERISTICSAt recommended operating conditions; voltages are referenced to GND (ground=0V).
Note All typical values are measured at Tamb =25 °C.
Philips Semiconductors Product specification
Dual D-type flip-flop with set and reset;
positive-edge trigger 74ALVC74
CHARACTERISTICS
Philips Semiconductors Product specification
Dual D-type flip-flop with set and reset;
positive-edge trigger 74ALVC74
Note All typical values are measured at Tamb =25 °C.
WAVEFORMS
Philips Semiconductors Product specification
Dual D-type flip-flop with set and reset;
positive-edge trigger 74ALVC74
