74ABT32N ,Quad 2-input OR gateLOGIC DIAGRAMCONDITIONS1A03SYMBOL PARAMETER T = 25°C; TYPICAL UNITamb2 Y0B0GND = 0V4A16Propagation5 ..
74ABT373 ,Octal Transparent Latch with 3-STATE OutputsFunctional Description Truth TableThe ABT373 contains eight D-type latches with 3-STATEInputs Outpu ..
74ABT373AD ,Octal transparent latch (3-State)PIN CONFIGURATION PIN DESCRIPTIONPIN NUMBER SYMBOL FUNCTION1 OE Output enable input (active-Low)OE ..
74ABT373AD ,Octal transparent latch (3-State)PIN CONFIGURATION PIN DESCRIPTIONPIN NUMBER SYMBOL FUNCTION1 OE Output enable input (active-Low)OE ..
74ABT373ADB ,Octal transparent latch 3-StateINTEGRATED CIRCUITS74ABT373AOctal transparent latch (3-State)Product specification 1995 Feb 17IC23 ..
74ABT373APW ,Octal transparent latch (3-State)FEATURES DESCRIPTIONThe 74ABT373A high-performance BiCMOS device combines low• 8-bit transparent l ..
74FCT16500CTPVCTG4 , 18-Bit Registered Transceivers
74FCT16652ATPVCTG4 , 16-Bit Registered Transceivers
74FCT16652CTPVCTG4 ,16-Bit Bus Transceivers and Registers with 3-State Outputs 56-SSOP -40 to 85Block DiagramsOEAB1 OEAB2OEBA OEBA1 2CLKBA1CLKBA2SBASBA 21CLKABCLKAB 21SAB SAB2 B REG1 B REGD DC CA ..
74FCT240 ,Inverting Octal Buffer/Line Driver with TRI-STATE Outputsfeatures GTO output control and undershoot I 64 mA (commercial), 48 mA (military)OLcorrector in add ..
74FCT240 ,Inverting Octal Buffer/Line Driver with TRI-STATE OutputsFeaturesYI and I reduced to 40.0 mA andg2.5 mAThe ’FCT240 is an inverting octal buffer and line dri ..
74FCT244 , FCT Interface Logic Octal Buffers/Line Drivers, Three-State
74ABT32D-74ABT32N
Quad 2-input OR gate
Product specification 1995 Sep 22
IC23 Data Handbook
Philips Semiconductors Product specification
74ABT32Quad 2-input OR gate
QUICK REFERENCE DATA
PIN CONFIGURATION
PIN DESCRIPTION
LOGIC SYMBOL
LOGIC DIAGRAM
LOGIC SYMBOL (IEEE/IEC)
FUNCTION TABLE
NOTES:= High voltage level= Low voltage level
ORDERING INFORMATION
Philips Semiconductors Product specification
74ABT32Quad 2-input OR gate
ABSOLUTE MAXIMUM RATINGS1, 2
NOTES: Stresses beyond those listed may cause permanent damage to the device. These are stress ratings only and functional operation of the
device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to
absolute-maximum-rated conditions for extended periods may affect device reliability. The performance capability of a high-performance integrated circuit in conjunction with its thermal environment can create junction
temperatures which are detrimental to reliability. The maximum junction temperature of this integrated circuit should not exceed 150°C. The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
RECOMMENDED OPERATING CONDITIONS
DC ELECTRICAL CHARACTERISTICS
NOTES: Not more than one output should be tested at a time, and the duration of the test should not exceed one second. This is the increase in supply current for each input at 3.4V. For valid test results, data must not be loaded into the flip-flop or latch after applying the power.
Philips Semiconductors Product specification
74ABT32Quad 2-input OR gate
AC CHARACTERISTICSGND = 0V; tR = tF = 2.5ns; CL = 50pF, RL = 500Ω
NOTE: Skew is defined as the absolute value of the difference between the actual propagation delay for any two separate outputs of the same
device. The specification applies to any outputs switching in the the same direction, either HIGH–to-LOW (tOSHL) or LOW-to-HIGH (tOSLH);
parameter guaranteed by design.
AC WAVEFORMSVM = 1.5V, VIN = GND to 3.0V
Waveform 1. Propagation delay for inverting outputs
Waveform 2. Common edge skew
TEST CIRCUIT AND WAVEFORMS
Philips Semiconductors Product specification
74ABT32Quad 2-input OR gate
DIP14: plastic dual in-line package; 14 leads (300 mil) SOT27-1
Philips Semiconductors Product specification
74ABT32Quad 2-input OR gate
SO14: plastic small outline package; 14 leads; body width 3.9 mm SOT108-1