5962-9313201MPA-AD810AN-AD810AR-AD810AR-REEL Fast Delivery |IC PHOENIX CO.,LIMITED

5962-9313201MPA ,Low Power Video Op Amp with DisableSPECIFICATIONSA S L1AD810A AD810SParameter Conditions V Min Typ Max Min Typ Max UnitsSDYNAMIC PERFO ..
5962-9325801M2A ,Quad Precision, High Speed Operational Amplifierapplications NC NC5 17OP467OP467+IN B 5 +IN Cwhere, traditionally, more than one op amp was used to ..
5962-9325901MPA ,Ultra Low Noise Wideband Op Amp
5962-9452101MCA ,Precision Picoampere Input Current Quad Operational AmplifierSpecifications subject to change without notice.–2– REV. DOP4971ABSOLUTE MAXIMUM RATINGS ORDERING G ..
5962-9459101MYA ,Low Power 8-Bit Shift RegisterGeneral DescriptionThe F100341 contains eight edge-trigged, D-type flipflops with individual inputs ..
5962-9466903QXA ,Floating-Point Digital Signal Processors, Militaryfeatures of the DMA processor are:D Link pointers that allow DMA channels to autoinitialize without ..
7464 ,DIGITALLY CONTROLLED AUDIO PROCESSOR WITH SRS SURROUND SOUND AND VOICE CANCELLERTDA7464DIGITALLY CONTROLLED AUDIO PROCESSOR WITHSRS SURROUND SOUND AND VOICE CANCELLERThe Device in ..
7473 ,Dual Master-Slave J-K Flip-Flops with Clear and Complementary OutputsGeneral Descriptiontransferred to the slave. The logic states of the J and KThis device contains tw ..
747905-2 , RECEPTACLE ASSEMBLY, SOLDER CUP, SIZE 1, 9 POSITION, AMPLMITE
7486 ,Quad 2-Input Exclusive-OR GateDM7486 Quad 2-Input Exclusive-OR GateSeptember 1986Revised February 2000DM7486 Quad 2-Input Exclusi ..
7489 ,64 Bit RAM89 CONNECTION DIAGRAM PINOUT A / suiiiiiicf"""'" 4 LS/74LS89 d) // 17fd? 64-BIT RANDO ..
749020010 , Spezifikation für Freigabe specification for release

5962-9313201MPA-AD810AN-AD810AR-AD810AR-REEL
Low Power Video Op Amp with Disable
CONNECTION DIAGRAM
8-Pin Plastic Mini-DIP (N), SOIC (R)
and Cerdip (Q) Packages
OFFSET
NULLTOP VIEW
AD810DISABLES
OUTPUT
OFFSET
NULL
–IN
+INS
REV.ALow Power
Video Op Amp with Disable
FEATURES
High Speed
80 MHz Bandwidth (3 dB, G = +1)
75 MHz Bandwidth (3 dB, G = +2)
1000 V/ms Slew Rate
50 ns Settling Time to 0.1% (VO = 10 V Step)
Ideal for Video Applications
30 MHz Bandwidth (0.1 dB, G = +2)
0.02% Differential Gain
0.048 Differential Phase
Low Noise
2.9 nV/√Hz Input Voltage Noise
13 pA/√Hz Inverting Input Current Noise
Low Power
8.0 mA Supply Current max
2.1 mA Supply Current (Power-Down Mode)
High Performance Disable Function
Turn-Off Time 100 ns
Break Before Make Guaranteed
Input to Output Isolation of 64 dB (OFF State)
Flexible Operation
Specified for 65 V and 615 V Operation
62.9 V Output Swing Into a 150 V Load (VS = 65 V)
APPLICATIONS
Professional Video Cameras
Multimedia Systems
NTSC, PAL & SECAM Compatible Systems
Video Line Driver
ADC/DAC Buffer
DC Restoration Circuits
PRODUCT DESCRIPTION
The AD810 is a composite and HDTV compatible, current
feedback, video operational amplifier, ideal for use in systems
such as multimedia, digital tape recorders and video cameras.
The 0.1 dB flatness specification at bandwidth of 30 MHz
(G = +2) and the differential gain and phase of 0.02% and
0.04° (NTSC) make the AD810 ideal for any broadcast quality
video system. All these specifications are under load conditions
of 150 Ω (one 75 Ω back terminated cable).
The AD810 is ideal for power sensitive applications such as
video cameras, offering a low power supply current of 8.0 mA
max. The disable feature reduces the power supply current to
only 2.1 mA, while the amplifier is not in use, to conserve
power. Furthermore the AD810 is specified over a power supply
range of ±5 V to ±15 V.
The AD810 works well as an ADC or DAC buffer in video
systems due to its unity gain bandwidth of 80 MHz. Because the
AD810 is a transimpedance amplifier, this bandwidth can be
maintained over a wide range of gains while featuring a low
noise of 2.9 nV/√Hz for wide dynamic range applications.
Differential Gain and Phase vs. Supply Voltage1001000
CLOSED-LOOP GAIN – dB
PHASE SHIFT – Degrees
FREQUENCY – MHz
Closed-Loop Gain and Phase vs. Frequency, G = +2,
RL = 150, RF = 715 Ω
AD810–SPECIFICATIONS(@ TA = +258C and VS = 615 V dc, RL = 150 V unless otherwise noted)
ABSOLUTE MAXIMUM RATINGS1
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .±18 V
Internal Power Dissipation2 . . . . . . .Observe Derating Curves
Output Short Circuit Duration . . . .Observe Derating Curves
Common-Mode Input Voltage . . . . . . . . . . . . . . . . . . . . . .±VS
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . .±6 V
Storage Temperature Range
Plastic DIP . . . . . . . . . . . . . . . . . . . . . . . .–65°C to +125°C
Cerdip . . . . . . . . . . . . . . . . . . . . . . . . . . .–65°C to +150°C
Small Outline IC . . . . . . . . . . . . . . . . . . .–65°C to +125°C
Operating Temperature Range
AD810A . . . . . . . . . . . . . . . . . . . . . . . . . . .–40°C to +85°C
AD810S . . . . . . . . . . . . . . . . . . . . . . . . . .–55°C to +125°C
Lead Temperature Range (Soldering 60 sec) . . . . . . .+300°C
NOTESStresses above those listed under “Absolute Maximum Ratings” may cause
permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated in the
operational section of this specification is not implied. Exposure to absolute
maximum raring conditions for extended periods may affect device reliability.8-Pin Plastic Package: θJA = 90°C/Watt; 8-Pin Cerdip Package: θJA = 110°C/Watt;
8-Pin SOIC Package: θJA = 150°C/Watt.
ESD SUSCEPTIBILITY
ESD (electrostatic discharge) sensitive device. Electrostatic
charges as high as 4000 volts, which readily accumulate on the
human body and on test equipment, can discharge without
detection. Although the AD810 features ESD protection
circuitry, permanent damage may still occur on these devices if
they are subjected to high energy electrostatic discharges.
Therefore, proper ESD precautions are recommended to avoid
any performance degradation or loss of functionality.
ORDERING GUIDE
Turn On Time
Min Disable Pin Current to
POWER SUPPLY
NOTESSee Analog Devices Military Data Sheet for 883B Specifications.Slew rate measurement is based on 10% to 90% rise time with the amplifier configured for a gain of –10.Voltage Swing is defined as useful operating range, not the saturation range.Disable guaranteed break before make.Turn On Time is defined with ±5 V supplies using complementary output CMOS to drive the disable pin.
Specifications subject to change without notice.
MAXIMUM POWER DISSIPATION
The maximum power that can be safely dissipated by the
AD810 is limited by the associated rise in junction temperature.
For the plastic packages, the maximum safe junction tempera-
ture is 145°C. For the cerdip package, the maximum junction
temperature is 175°C. If these maximums are exceeded momen-
tarily, proper circuit operation will be restored as soon as the die
temperature is reduced. Leaving the device in the “overheated”
condition for an extended period can result in device burnout.
To ensure proper operation, it is important to observe the
derating curves.
TOTAL POWER
DISSIPATION – Watts
AMBIENT TEMPERATURE – °C
Maximum Power Dissipation vs. Temperature
While the AD810 is internally short circuit protected, this may
not be sufficient to guarantee that the maximum junction
temperature is not exceeded under all conditions.
0.1µF+VS
–VS
SEE TEXT
AD810
AD810
MAGNITUDE OF THE OUTPUT VOLTAGE – ±Volts
SUPPLY VOLTAGE – ±Volts
Figure 1.Input Common-Mode Voltage Range vs.
Supply Voltage1010010k1k
OUTPUT VOLTAGE – Volts p-p
LOAD RESISTANCE – Ohms
Figure 3.Output Voltage Swing vs. Load Resistance
INPUT BIAS CURRENT – µA
JUNCTION TEMPERATURE – °C
Figure 5.Input Bias Current vs. Temperature
–Typical Characteristics
MAGNITUDE OF THE OUTPUT VOLTAGE – ±Volts
SUPPLY VOLTAGE – ±Volts
Figure 2.Output Voltage Swing vs. Supply
Figure 4.Supply Current vs. Junction Temperature
INPUT OFFSET VOLTAGE – mV
JUNCTION TEMPERATURE – °C
–10
Figure 6.Input Offset Voltage vs. Junction Temperature
250–60+140
+100+120+80+60+40+200–20
SHORT CIRCUIT CURRENT – mA
JUNCTION TEMPERATURE – °C
Figure 7.Short Circuit Current vs. Temperature
100k100M10M1M10k
0.1
CLOSED-LOOP OUTPUT RESISTANCE –
FREQUENCY – Hz
Figure 9.Closed-Loop Output Resistance vs. Frequency
100k1M100M10M
FREQUENCY – Hz
OUTPUT VOLTAGE – Volts p-p
Figure 11.Large Signal Frequency Response
120+140
+120+100+80+60+40+200–20
OUTPUT CURRENT – mA
JUNCTION TEMPERATURE – °C
Figure 8.Linear Output Current vs. Temperature
Figure 10.Output Resistance vs. Frequency,
Disabled State
Figure 12.Input Voltage and Current Noise vs. Frequency
AD810
–Typical Characteristics
Figure 14.Power Supply Rejection vs. Frequency
–1401001k10M1M100k10k
HARMONIC DISTORTION – dBc
FREQUENCY – Hz
Figure 16.Harmonic Distortion vs. Frequency (RL = 400 Ω)
Figure 18.Slew Rate vs. Supply Voltage
100100k100M10M1M10k
FREQUENCY – Hz
COMMON-MODE REJECTION – dB
Figure 13.Common-Mode Rejection vs. Frequency
1001k10M1M100k10k
HARMONIC DISTORTION – dBc
FREQUENCY – Hz
Figure 15.Harmonic Distortion vs. Frequency (RL = 100 Ω)
OUTPUT SWING FROM ±V TO 0V
SETTLING TIME – ns
Figure 17.Output Swing and Error vs. Settling Time
Figure 20.Small Signal Pulse Response, Gain = +1,
RF = 1 kΩ, RL = 150 Ω, VS = ±15 V100
1 1000
CLOSED-LOOP GAIN – dB
PHASE SHIFT – Degrees
FREQUENCY – MHz
Figure 22.Closed-Loop Gain and Phase vs. Frequency,
G= +1, RF = 1 kΩ for ±15 V, 910 Ω for ±5 V and ±2.5 V
Figure 24.–3 dB Bandwidth vs. Supply Voltage
G = +1, RL = 1 kΩ
AD810HP8130
PULSE
GENERATOR
–VS0.1µFVIN
Figure 19.Noninverting Amplifier Connection1001000
CLOSED-LOOP GAIN – dB
PHASE SHIFT – Degrees
FREQUENCY – MHz
Figure 21.Closed-Loop Gain and Phase vs. Frequency,
G= +1. RF = 1 kΩ for ±15 V, 910 Ω for ±5 V and ±2.5 V
–3dB BANDWIDTH – MHz
SUPPLY VOLTAGE – ±Volts
Figure 23.Bandwidth vs. Supply Voltage,
Gain = +1, RL = 150 Ω
AD810
–Typical Characteristics, Noninverting Connection
Figure 26.Large Signal Pulse Response, Gain = +10,
RF = 442 Ω, RL = 400 Ω, VS = ±15 V
Figure 28.Closed-Loop Gain and Phase vs. Frequency,
G = +10, RL = 1 kΩ
Figure 30.–3 dB Bandwidth vs. Supply Voltage,
Gain = +10, RL = 1 kΩ20nS
VIN
Figure 25.
RF = 442 Ω, RL = 150 Ω, VS = ±15 V1001000
CLOSED-LOOP GAIN – dB
PHASE SHIFT – Degrees
FREQUENCY – MHz
Figure 27.Closed-Loop Gain and Phase vs. Frequency,
G = +10, RL = 150 Ω
–3dB BANDWIDTH – MHz
SUPPLY VOLTAGE – ±Volts
Figure 29.–3 dB Bandwidth vs. Supply Voltage,
Gain = +10, RL = 150 Ω

Partno	Mfg	Dc	Qty	Available	Descript
5962-9313201MPA \|59629313201MPA	ADI	N/a	296	avai	Low Power Video Op Amp with Disable
AD810AN	AD	N/a	82	avai	Low Power Video Op Amp with Disable
AD810AR	ADI	N/a	57	avai	Low Power Video Op Amp with Disable
AD810AR-REEL \|AD810ARREEL		N/a	40	avai	Low Power Video Op Amp with Disable