74ACTQ244SJ ,Quiet Series Octal Buffer/Line Driver with 3-STATE OutputsFeaturesThe ACQ/ACTQ244 is an octal buffer and line driver
54ACTQ244DMQB-74ACTQ244SCX
Quiet series octal buffer/line driver with TRI-STATE outputs. Devices shipped in 13 inches reels.
National
Semiconductor
54ACQ/74ACQ244 © 54ACTQ/74ACTQ244
Quiet Series Octal Buffer/Line Driver
with TRl-STATE8 Outputs
General Description
The 'ACO/'ACT0244 is an octal buffer and line driver de-
signed to be employed as a memory address driver, clock
driver and bus oriented transmitter or receiver which pro-
vides improved PC board density. The ACQ/ACTQ utilizes
NSC Quiet Series technology to guarantee quiet output
switching and improved dynamic threshold performance.
FACT Quiet SeriesTM features GTOTM output control and
undershoot Corrector in addition to a split ground bus for
superior performance.
Features
September 1990
Guaranteed simultaneous switching noise level and dy-
namic threshold performance
Guaranteed pin-to-pin skew AC performance
Improved latch-up immunity
TRI-STATE® outputs drive bus lines or buffer memory
address registers
Outputs source/sink 24 mA
Faster prop delays than the standard 'AC/‘ACT244
4 kV minimum ESD immunity
Standard Military Drawing (SMD)
- 'ACT0244: 5962-8776003
Logic Symbol Connection Diagrams
IEE/IEC Pin Assignment Pin Assignment
for DIP, Flatpak and SOIC for Lee and PCC
o I o I o I
_ I 3 s 2 s 1
0:1 2 Vcc E] E El IE
00 k: 3 o-r,
o, o q, o, E - IE! 04
02 I: 4 I4 "til FL E '0_
5 7 r E] OE,
03 os 6 th OJE l]; / " IVcc
I2 7 Is Is a o%
os 8 02 I-,- .-,-1
ls 9 Is E] MI
o, o, w 03 th Is o, i4 q,
os arm I, TL/F/10235-3
TL/Fl10235-2
TL/F/10235-t
Truth Tables
Pin Names Description Inputs Outputs
- Pins12,14, 16, 18
DE, t% TRI-STATE Output Enable Inputs OE, In ( l
lo-I7 Inputs L L L
Oo-o; Outputs L H H
Inputs Outputs
tttia In (Pins 3, 5, r, 9)
H = HIGH Voltage Level
_ . . _ L = LOW Voltage Leva|
THI-STATE' Is a mgistered lrademadI of Nanonal Semiconductor Ca'porauon, x = Immaterial
FACTW. FACT Quiet Seuss”, and GT0m are trademarks of Naiional Semiconductor .
Corporation. Z = High Impedance
© I990 National Semictrnductix Corporation TL/F/ I 0235
RRD-B2NM20fprtrtmd In U S. A,
VVZOLOVVL/OLOVVS 0 VVZOOVVUOOVVS
SIHdIDO ELVLS'IHL UllM JaAl-IG eUI'I/Jeuna |9190 seuas IaIno
Absolute Maximum Rating (Note1)
" Milltary/Aerospace specified devices are required,
please contact the National Semiconductor Sales
Office/Dlstributors for avallabllity and specifications.
Supply Voltage (Vcc) - 0.5V to + 7.0V
DC Input Diode Current (lot)
VI = --0.5V -20 mA
VI = Vcc + 0.5V +20 mA
DC Input Voltage (Vi)
DC Output Diode Current (IOK)
-0.5V to VCC + 0.5V
Recommended Operating
Conditions
Supply Voltage (Vcc)
Input Voltage (Nh)
Output Voltage (V0)
Operating Temperature (T A)
74ACQ/ACTO
54ACQ/ACTQ
2.0V to 6.0V
4.5V to 5.5V
0V to Vcc
0V to Vcc
- 40'C to + 85°C
- 55°C to + 125''C
[t f J, 0'5: 0 5V 3:; ”‘2 Minimum Input Edge Rate AV/At
0 - CC . m 'ACO Devices
DC Output Voltage No) -0.5V to VCC + 0.5V VIN from 30% to 70% of Vcc
DC Output Source VCC © 3.0V, 4.5V, 5.5V 125 mV/ns
or Sink Current (lo) i 50 mA Minimum Input Edge Rate AV/At
DC Vcc or Ground Current 'ACTQ Devices
per Output Pin (ICC or IGND) , 50 mA Ihr: from o.sv to 2.0V
Storage Temperature (T STG) _ 65''C to + 150°C Vcc @ 4.5V, 5.5V 125 mV/ns
DC Latch-Up Source or
Sink Current 1 300 mA
Junction Temperature (T J)
CDIP 175''C
PDIP 140''C
Note 1: Absolute maximum ratings are those values beyond which damage
to the device may occur. The databook tpscitications should be met, without
exception, to ensure that the system design is reliable over its power supply,
temperature, and output/input loading variables. National does not recom~
mend operation ot FACT circuits outside databook smrcifeations.
DC Electrical Characteristics for 'ACtt Family Devices
74ACO 54ACO 74ACQ
Symbol Parameter ti? " = + 25'C _ 55.02% C) 125''C _ "l, 'loc + 85°C Unlts Conditions
Typ Guaranteed Limits
VIH Minimum High Level 3.0 1.5 2.1 2.1 2.1 VoUT = 0.1V
InputVoltage 4.5 2.25 3.15 3.15 3.15 V or Vcc - 0.1V
5.5 2.75 3.85 3.85 3.85
" Maximum Low Level 3.0 1.5 0.9 0.9 0.9 VOUT = 0.1V
Input Voltage 4.5 2.25 1.35 1.35 1.35 V or Vcc - 0.1V
5.5 2.75 1.65 1.65 1.65
VOH Minimum High Level 3.0 2.99 2.9 2.9 2.9 [OUT = - 50 [LA
Outpu1Voltage 4.5 4.49 4.4 4.4 4.4 V
5.5 5.49 5.4 5.4 5.4
'vm = " OYVIH
3.0 2.56 2.4 2.46 - 12 mA
4.5 3.86 3.7 3.76 v IOH -24 mA
5.5 4.86 4.7 4.76 - 24 mA
VOL Maximum Low Level 3.0 0.002 0.1 0.1 0.1 [OUT = 50 MA
Output Voltage 4.5 0.001 0.1 0.1 0.1 V
5.5 0.001 0.1 0.1 0.1
'VIN = " OYVIH
3.0 0.36 0.50 0.44 12 mA
4.5 0.36 0.50 0.44 V IOL 24 mA
5.5 0.36 0.50 0.44 24 mA
IIN Maximum Input V. = Vcc, GND
Leakage Current 5.5 uF0.1 t1.0 uF1.0 "A (Note 1)
IOLD tMinimum Dynamic 5.5 50 75 mA VOLD = 1.65V Max
IOHD Output Current 5.5 -50 -75 mA VOHD = 3.85V Min
lcc Maximum Quiescent VIN = VCC
Supply Current 5.5 8.0 160.0 80.0 “A or GND (Note 1)
'All outputs loaded thresholds on input associated with output under test.
tMaximum test duration 2.0 ms, one output loaded at a time.
DC Electrical Characteristics for 'ACQ Family Devices (Continued)
74ACQ 54ACG 74ACO
Vcc = TA = TA = . . .
Symbol Parameter (V) TA + 25°C - 55''C to + 125°C _ 40'C to + 85°C Units Conditions
Typ Guaranteed Limits
I02 Maximum TRI-STATE V/OE) = VIL. "
Leakage Current 5.5 t 0.5 t 10.0 :50 ,u.A V. ' Vcc, GND
V0 = Vcc, GND
VOLP Quiet Output 5 0 1 1 1 5 V Figures 1,2
Maximum Dynamic VOL . . . (Notes 2, 3)
VOLV Quiet Output - - Figures l, J?
Minimum Dynamic VOL 5.0 0.6 I.2 V (Notes 2, 3)
VIHD Minimum High Level (Notes 2, 4)
Dynamic Input Voltage 5.0 3.1 3.5 V
VILD Maximum Low Level (Notes 2, 4)
Dynamic Input Voltage 5.0 IS 1.5 V
'AII outputs loaded thresholds on input associated with output under test.
tMaximum test duration 2.0 ms, one output loaded at a lime.
Note 1: IN and ICC © 3.0V are guaranteed to be less than or equal to (he raspsctive limit © 5.5V v00.
Note 2: Worst case package.
Note 3: Max number of outputs defined as (n). Data Inputs are driven 0V to 5V. One output © GND.
Note 4: Max number of Data Inputs 1n) switching. (n - 1) Inputs switching 0V to 5V ('ACC). Input-under-test switching: 5V to threshold (VILD). 0V to lhreshold
(VIHD).1 = 1 MHz.
DC Electrical Characteristics for 'ACTO Family Devices
'00 for 54ACQ ii? 25''C is identical to 74ACO @ 25''C.
74ACTO 54ACTQ 74ACTQ
Vcc = a TA = TA = . . .
Symbol Parameter (V) TA f 25 c _ 55°C to + 125°C - 401: to + 85''C Units Cttntiltitmtt
Typ Guaranteed Limits
1/iH Minimum High Level 4.5 1.5 2.0 2.0 2.0 V VOUT 2 0.1V
InputVoltage 5.5 1.5 2.0 2.0 2.0 or Vcc - 0.1V
Ihr. Maximum Low Level 4.5 1.5 0.8 0.8 0.8 V VOUT = 0.1V
Input Voltage 5.5 1.5 0.8 0.8 0.8 or Vcc - 0.1V
VOH Minimum High Level 4.5 4.49 4.4 4.4 4.4 V IOUT = -50 pA
Output Voltage 5.5 5.49 5.4 5.4 5.4
'VIN = " OFVIH
4.5 3.86 3.70 3.76 V lors -24 mA
5.5 4.86 4.70 4.76 ~24 mA
VOL Maximum Low Level 4.5 0.001 0.1 0.1 0.1 v IOUT = 50 ”A
Output Voltage 5.5 0.001 0.1 0.1 0.1
4 5 0 36 0 50 0 44 I.VIN = " "U: A
. . . . OL m
5.5 0.36 0.50 0.44 V 24 mA
IIN Maximum Input VI = Vcc, GND
Leakage Current 5.5 i 0.1 t 1.0 i 1.0 p.A
Ioz Maximum TRI-STATE + V: = lhc, VIH
Leakage Current 5.5 10.5 110.0 :50 0A vo = Vcc, GND
ICCT Maximum lcc/lnput 5.5 0.6 1.6 1.5 mA V. = Vcc - 2.1V
'OLD tMinimum Dynamic 5.5 50 75 mA VOLD = 1.65V Max
IOHD Output Current 5.5 - 50 - 75 mA VOHD = 3.85V Min
ICC Maximum Quiescent " = Vcc
Supply Current 5.5 B.0 160.0 80.0 “A or GND (Note 1)
VOLP Quiet Output 5 0 1 1 1 5 V Figures I, 2
Maximum Dynamic VOL . . ' (Notes 2, 3)
VOLv Quiet Output _ - Figures t, 2
Minimum Dynamic VOL 5.0 0.6 1.2 V (Notes 2, 3)
'All toutputs loaded thresholds on input associated with output under test.
tMaximum test duration 2.0 ms, one output loaded at a time.
DC Electrical Characteristics for 'ACTQ Family Devices (Continued)
74ACTQ 54ACTQ 74ACTQ
Symbol Parameter Vcc TA = +25°C TA = TA = Units Conditions
(V) _ 55'C to + 125°C -40''C to + 85''C
Typ Guaranteed Limits
V'HD M'mmufn High Level 5.0 1.9 2.2 V (Notes 2, 4)
Dynamic Input Voltage
ViLD Maximum Low Level
Dynamic Input Voltage 5.0 1.2 0.8 V (Notes 2, 4)
'AII outputs loaded; thresholds on input associated with output under test.
tMaximum test duration 2.0 ms, one output loaded at a time.
Note 1: ICC for 54ACTQ (ik 25°C is identical to 74ACTQ © 25°C.
Note 2: Worst case package.
Note 3: Max number of outputs defined as " Data Inputs are driven 0V to 3V. One output (i8 GND.
Note & Max number of Data Inputs (n) switching. (n- 1) Inputs switching 0V to 3V (’ACTQ). Input-under-test switching: 3V to threshoid Mar), 0V to threshold
(VIHD), f = 1 MHz.
AC Electrical Characteristics
74ACQ 54ACO 74ACO
. _ a TA = ~55°c TA = -40'C
Symbol Parameter 'tt 't L- gi', 7 to + 125°C to + 85°C Units
L p th. = so pF th. = so pF
Min Typ Max Min Max Min Max
tpHL. tpLH Propagation Delay 3.3 2.0 7.0 9.0 2.0 9.5 ns
Data to Output 5.0 1.5 5.0 6.0 1.5 6.5
tPZL, tPZH Output Enable Time 3.3 2.5 8.0 12.0 2.5 12.5 ns
5.0 1.5 6.5 8.0 1.5 8.5
tsz, tPLZ Output Disable Time 3.3 1.0 9.0 13.5 1.0 14.0 ns
5.0 1.0 7.5 9.0 1.0 9.5
tOSHL, Output to Output 3.3 1.0 1.5 1.5 ns
tOSLH Skew" Data to Output 5.0 0.5 1.0 1.0
'Voltage Range 5.0 is 5.0V 10.5V.
Voltage Range 3.3 is 3.3V t0.3V.
. 'Skew is defined as the absolute value of the difference between the actual propagation delay for any two separate outputs ot the same device. The specirisaron
applies to any outputs switching in the same direction, either HIGH to LOW (103m) " LOW to HIGH (IOSLH). Parameter guaranteed by design.
AC Electrical Characteristics
74ACTO 54ACTQ 74ACTG
. == Q TA = -55'C TA = -4trc
Symbol Parameter V678 2 = 2:5: to + 125°C to + 85''C Units
L p CL = 50 pF th. = so pF
Min Typ Max Min Max Min Max
tpHL, tpLH Propagation Delay
Data to Output 5.0 1.5 5.5 6.5 1.5 9.0 1.5 7.0 ns
tPZL. tsz Output Enable Time 5.0 1.5 7.0 8.5 1.5 10.5 1.5 9.0 ns
tsz, tPLZ Output Disable Time 5.0 1.0 8.0 9.5 1.5 10.5 1.0 10.0 ns
tOSHL, Output to Output
tOSLH Skew '' 5.0 0.5 1.0 1.0 ns
Data to Output
'Voltage Range 5.0 is 5.0V ttHN.
' 'Skew is defined as the absolute value of the difference between the actual propagation delay for any two separate outputs of the same device. The specification
applies to any outputs switching in the same direction, either HIGH to LOW “OSHU or LOW to HIGH (tOSLH). Parameter guaranteed by design.
Capacitance
Symbol Parameter Typ Units Conditions
CIN Input Capacitance 4.5 pF Vcc = 5.0V
CPD Pwerpissipation 70 pF Vcc = 5.0V
Capacitance
FACT Noise Characteristics
The setup of a noise characteristics measurement is critical
to the accuracy and repeatability of the tests. The following
is a brief description of the setup used to measure the noise
characteristics of FACT.
Equipment:
Hewlett Packard Model 8180A Word Generator
PC-163A Test Fixture
Tektronics Model 7854 Oscilloscope
Procedure:
1. Verify Test Fixture Loading: Standard Load 50 pF, 500n.
2. Deskew the word generator so that no two channels have
greater than 150 ps skew between them. This requires
that the oscilloscope be deskewed first. Swap out the
channels that have more than 150 ps of skew until all
channels being used are within 150 ps. It is important to
deskew the word generator channels before testing. This
will ensure that the outputs switch simultaneously.
3. Terminate all inputs and outputs to ensure proper loading
of the outputs and that the input levels are at the correct
voltage.
4. Set Vcc to 5.0V.
5. Set the word generator to toggle all but one output at a
frequency of 1 MHz. Greater frequencies will increase
DUT heating and affect the results of the measurement.
6. Set the word generator input levels at 0V LOW and 3V
HIGH for ACT devices and 0V LOW and 5V HIGH for AC
devices. Verify levels with a digital volt meter.
VOLP/VOLV and VOHP/VOHV=
0 Determine the quiet output pin that demonstrates the
greatest noise levels. The worst case pin will usually be
the furthest from the ground pin. Monitor the output volt-
ages using a 500 coaxial cable plugged into a standard
SMB type connector on the test fixture. Do not use an
active FET probe.
q Measure VOLP and vow on the quiet output during the
HL transition. Measure VOHp and VOHV on the quiet out-
put during the LH transition.
- Verify that the GND reference recorded on the oscillo-
scope has not drifted to ensure the accuracy and repeat-
ability of the measurements.
VILD and VIHD:
q Monitor one of the switching outputs using a 500 coaxial
cable plugged into a standard SMB type connector on
the test fixture. Do not use an active FET probe.
. First increase the input LOW voltage level. VIL, until the
output begins to oscillate. Oscillation is defined as noise
on the output LOW level that exceeds VIL limits, or on
output HIGH levels that exceed Vm limits. The input
LOW voltage level at which oscillation occurs is defined
as VILD~
. Next increase the input HIGH voltage level on the word
generator, VH4 until the output begins to oscillate. Oscilla-
tion is defined as noise on the output LOW level that
exceeds " limits, or on output HIGH levels that exceed
VIH limits. The input HIGH voltage level at which oscilla-
tion occurs is defined as VIHD.
. Verify that the GND reference recorded on the oscillo-
scope has not drifted to ensure the accuracy and repeat-
ability of the measurements.
ACTIVE
OUTPUTS
OUTPUT
UNDER TEST
TL/F/tof?'
FIGURE 1. Quiet Output Noise Voltage Waveforms
Note A. VOW and vow are measured with respect to ground reference.
Note B. Input pulses have the following characteristics" = 1 MHz, t, = 3 ns, tt = 3 ns, skew < 150 ps.
Ci) 7-Iniputs t, 450.0. C)
HP 81 BOA ' " TEK 7854
WORD 50 pF Oscilloscope
GENERATOR g 5011 Inputs
GND 50 pF Probes are grounded as
x close to DOT pins as possible.
GND is supplied vla 4, Load capacitors are placed
tt copper plane as close to OUT as possible.
TL/F/10235-5
FIGURE 2. Simultaneous Switching Test Circuit
Ordering Information
The device number is used to form part of a simplified purchasing code where the package type and temperature range are
defined as follows:
74ACTQ 244 P C
Temperature Range Family Special Variations
74ACQ = Commercial X = Devices shipped in 13" reels
54ACQ = Military OR = Commercial grade device with
74ACTQ = Commercial TTL-Compatible burn-in
54ACTQ = Military TTL-Compatible QB z Military grade device with
. environmental and burn-in
Device Type processing shipped in tubes
Package fo?' Temperature Range
P = Plastic DIP
C = Commercial (- 40''C to ' 85''C)
Ceramic DF M = Military (-55"C to + 125°C)
F Flatpak
L = Leadless Chip Carrier (LCC)
== Plastic Leaded Chip Carrier (PCC)
= Small Outline Package (SOIC)
Physical Dimensions inches (millimeters)
0.200110%
(5.030301?!)
0.015 t0.010
f (0.301 tll 254)
/" Iran - 0.011
tl.350f_ihtm 0015 /
(0090:0203) - ----i!yl,,i,3Afl-,l, (0.32m / -_-_--
' (1.6004905! mm n? , -lth178-t1.27g)
X f/ n m
0.022 _ 0.020
- "0.559-tl,rW
0.077 -0.iBI j ' Tre
(IS5g-t.361) 1 -
. 0.06-0.05: A
F (1.1034307; -- -
4mm A "P '/,'-ti,t-yilt-',,--l ._ 0.045 -0155
"m'',,-,', '1 ) (1.u3-1.397)
Top Vlow Side View “P
Ci' x 004010.010
(1010:0254)
3 PLCS
Bottom View
thi03 (3.3%?)
(0.016 .
mu 11W MhX m
0.022 - -
o." ' + 0.0%
MAX m (tlA52)
Detail A
L20! IREV "
20-Terminal Ceramic Leadless Chlp Carrier (L)
NS Package Number E20A
Physical Dimensions inches (millimeters) (Continued)
(0.635)
--tis'
(25. Ef"?
is';,,-,-,---,,,,'-",?'')'',-',,,-,,-,,-,,,-,-,,,'-'",;
MN-tMN - _
(5.588- 7.014)
I1lLtlltlrtJltlLtijll1lltll1d
Ih005-0.020
tlhW7-0.508)
Mil "P 003110.005
[034010.127]
tum 005520.005
th_t81 "90-0.3N - [0.121) 1139110127) 0320-0,an
(2. TH - -.--
MAX (r.im6-8.1tlb) SUSS SEALAN" MIN (0.5m_1.5u)
= th 200
(5. tt80)
l fl CQ --H---r-l'il'r1u's, MAX "
95° t5'' tltr M" f-iii-i-',--, 0
0.008-0.01t 'll-fl-, (t.ft5- 0.200
(0.2004005) 'li? (a 175- b. 030)
L,t:.iysres11/r. B. 310- 0.410 +1 0.060 Ir-trt/ini, 01020. 003
[1. an- 10. 41) (1.5241 (0. 4511!! tmi)
30TH ENOS M
(254010.254)
JQDAWEV My
20-Lead Ceramic Duai-In-Line Package (D)
NS Package Number J20A
ItA96-trM2
' ttt.598--u.0W) .
-iiiiii)iiiiiiih1i)
"M-IM"
tttrll08-lih6431
IO 30" m
LEAD " 1
IDEN'I
0m aux
t0254)
"81-tLt99
F391-h595)
0010-0029 ci"-- tm-6.tM
(tr.tu-th73r) A - - t2a62-t.66t)
V'm"? 1yA%-...tULI?..
ALL Lms (0102-0305)
LIEU - “ 5 - - - - sumac
"N-troto M21 we--' e l "" 0050 l 0014+ 0020
=L---= (0102) 001570050 W - - === I F - _ m'
[tum-ram; An m0 ms + 10400 4.270) t I (117!) (0.356 415“)
m ALL LEAI2S m ILL mus m
_, J.Li.r1b"
loam ummtv n
20-Lead Small Outline Integrated Circuit (S)
NS Package Number M208
Physical Dimensions inches (millimeters) (Continued)
I (1,9N-0.00
0.092 X 0.030 (2C638-25AM)
12.331 y 11.71121\l omzmnns
MAX " MI m mu”! [rsLrrsl Fil IT?! m m FiiiiTGWh
PIN 00.11051“ "x (h240-0.260 MD
"ss, (8.tm-tr604l PIN ND IIDEI‘IT\‘°
_0.zw - 09110111 I
llf yll_tjLe3.Jltll_sJuJLUltlLtJltArl
028041.325 , - m’ 0PT|0N2
(7 stit-irisTtj Iriialtel! - 0-040 - F OPTION? .1 0130 0005
l 0055 (1.5241 11.1115) l 4''tax) t- fi;
13.3112 0.1211
I i (teil) TYP 11? 1 -
I I I I I I I I) iht65-ir200
f _ 7 I (083-5.08il)
0.003-0015‘ 9050.004" - I 1
[0.203-0.381I [ - 0.020
010010.010 ‘I L tyt25-th15i) 111.5031
iri_utl, P12540205“ . M114-th023 - (3.17li-3.810l MIN
0.350 (1.016) (i)355-0di85)
e v NOM
19,3901
MOBIREVI)
20-Lead Plastic Dual-ln-Line Package (P)
NS Package Number N208
4 SPACES AT
- fl 0.045
(1.270] m <7
19 N 1 2 3 A x45°
I I I l 0-08"
- m_llllll m,
A " Ollt MOM
quasm.
, [""'. 15: VIEW A-A
4 smss AT 13 9
0.050 l - 0.226
1270) [5.740)
sauna;
Ih310-0.330 _ -
(1.374 - L382) I
(conmn 01111511510141
(htn3-t018
‘* 10 330- 0 1571
0026-0032 -.-
2-2-i-,rt,l/r"iijllc'll'-ttt
1 HP {1.5001
- - - MIN
0.tm-0.0ts f I T 0_0_.32- o 040
(0.1tt-0.381) -
il.tiH--0n18 -..i-At II tTriiTs-o-a1ti, 813- 10151
(h6C-2.g97) k 0.350 _0.165A0.180
(8.8901 1:191 -4.572)
PIN 110.1 IIEF so
IDENT trM5-0.395
(9,7N-10.03)
SOUMIE V20A (REV "
20-Lead Plastic Chip Carrier (Q)
NS Package Number V20A
th TRl-STATE Outputs
Iver wi
D‘IAUUI IQAUUZ‘I"! ' O‘lHU I U] I “AD I U444
Quiet Series Octal Buffer/Line Dr
Physical Dimensions inches (millimeters) (Continued)
0060-0090 0.540 MAX
(1. 524-2. 286) (13.72)
- 0. 030-0. 040 WP (h050_t0.0t)5 o_. 005 MIN m,
_ (0762-1016) (1-270T$3.127)" -(tr.i-rr, 127)
(E.SSD-BJZB)
I 20191817161514131211
o_. 285
“(07‘ gigs l (6.6iu-6.858)
1 r 4 5 ti 7 5 910 0.008-0.012J
u Jd (t5rtfs-tistri) 203-0. 305
SEE A t DETAIL A
DETAIL A/l/ I 0250-0320
PIN fl (5.350 8.128)
wm (sz 0)
_,IL_ 0.004-0. 006 - L-ttit-tgs', 0.015-0. 019 o_.045
(0.102-H) 102-0. 152) (ir.iG-?i.iiri)m' 0.381-0. (tsan-Hs) TYP -d,, 'tici-ii, 143) mu TTP
LIFE SUPPORT POLICY
20-Lead Ceramic Flatpak (F)
NS Package Number W20A
Lit. ' 114674
NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OH SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL
SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and whose
faiiure to perform, when properly used in accordance
with instructions for use provided in the labeling, can
be reasonably expected to result in a significant injury
2. A critical component is any component of a life
support device or system whose failure to perform can
be reasonably expected to cause the failure of the life
support device or system, or to affect its safety or
effectiveness.
to the user. .. ...-
Nation! Semicondudor Mammal Semiconductor Ftatktrtal Sqtttbttottdugtttr Mona! Sqtttittttttttutttttr National Somnondmons National Semiconductor
Componuon GmbH Japan Ltd. Hong Kong w. tht Brul Ltd; (Amhlll) PTY. Ltd.
2900 Semiconductor Drive Itt6ustnttstrtgsstt 10 Sansoido Bldg. 5F Suite 513, 5th Floor Av. Brig. Faria Lima, 1383 lst Floor, 441 s. Kikia Rd.
PO. Box 58090 D6080 FursttmftMtxuck 4-15 Nishi Shinjuku CNnadtom Golden Plaza, 60 AodttGorti. 62 Melbourne. 3004
Santa Clara. CA 95052-8090 West Germany Shinluku-Ku, 77 Matt Road, Tsmshmsui East, 01451 Sao Paulo, SP, Brasil Victory. Austalia
Tel: 1(800) 272-9959 Tel: (081-41) 103-0 Tokyo 160. Japan Kowloon. Hong Kong Tet. (55/11) 212-5066 Tel: (03) 257-5000
TWX: (910) 339AW40 Talent: 527449 Tel: 3-299-1001 Tel; 3-7231290 Fax: (56/11) 211-1181 NSBR BR Fax: 61»3-2677458
Fax: (06141) 103554 FAX: 34994000 Telex: 52996 NSSEA HX
Fax: 34112536
National does not assume any "tgportMy'lity tot use th any tirtaWy deserted. no titil patemtlkamses an; iwlied andNatitmal reserves the right at any ttttttt without notice to change said circuitry md sgxxi6ratkxts,
This datasheet has been :
www.ic-phoenix.com
Datasheets for electronic components.
National Semiconductor was acquired by Texas Instruments.
corp/docs/irwestor_relations/Pr_09_23_201 1_national_semiconductor.html
This file is the datasheet for the following electronic components:
54ACTQ244QMX - product/54actq244qmx?HQS=TI-nu|I-nu|I-dscataIog-df-pf-null-wwe
74ACQ244LCX - product/74acq244lcx?HQS=T|-nu|I-nulI-dscatalog-df-pf—null-wwe
54ACQ244SMQB - product/54acq244smqb?HQS=T|-nuIl-nulI-dscatalog-df—pf—nuII-wwe
54ACQ244SMX - product/54acq244smx?HQS=T|—nu|I-nuIl-dscataIog-df-pf-null-wwe
54ACTQ244DMQB - product/54actq244qub?HQS=T|-null-null-dscataIog-df-pf-null-wwe
54ACTQ244DMX - product/54actq244dmx?HQS=T|-nu|l-null-dscata|og-df—pf—nuII-wwe
54ACTQ244FMQB - product/54actq244fmqb?HQS=T|—null-nu|I-dscatalog-df-pf-nu||-wwe
54ACTQ244FMX - product/54actq244fmx?HQS=TI—nulI-null—dscataIog—df-pf-null-wwe
54ACTQ244LMQB - product/54actq244lmqb?HQS=T|-nu|I-nu|I-dscatalog-df-pf-null-wwe
54ACTQ244LMX - product/54actq244lmx?HQS=T|-nu|I-nulI-dscatalog-df—pf—null-wwe
54ACTQ244PMQB - product/54actq244pmqb?HQS=T|-nu|I-nulI-dscatalog-df-pf-null-wwe
54ACTQ244PMX - product/54actq244pmx?HQS=T|-nu|l-nulI-dscatalog-df—pf-nuII-wwe
54ACTQ244QMQB - product/54actq244qmqb?HQS=TI-nu|l-null-dscataIog-df-pf-null-wwe
74ACQ244PCQR - product/74acq244pcqr?HQS=TI-nu||-nu|I-dscataIog-df-pf-null-wwe
54ACQ244DMX - product/54acq244dmx?HQS=T|-nu|I-nulI-dscatalog-df—pf—nuII-wwe
54ACQ244FMX - product/54acq244fmx?HQS=TI-nulI-nulI—dscatalog—df-pf-nulI-wwe
54ACQ244LMX - product/54acq244lmx?HQS=T|—null-nulI-dscataIog-df-pf-null-wwe
54ACQ244PMQB - product/54acq244pmqb?HQS=T|—nuIl—nu|I—dscatalog-df-pf-null-wwe
54ACTQ244SMQB - product/54actq244smqb?HQS=TI-nu|I-null-dscataIog-df—pf-null-wwe
54ACTQ244SMX - product/54actq244smx?HQS=T|-nu|I—nu|I-dscataIog-df-pf-null-wwe
74ACQ244DCQR - product/74acq244dcqr?HQS=T|-nu||-nuII-dscataIog-df-pf-null-wwe
74ACQ244DCX - product/74acq244dcx?HQS=T|—nulI-nulI-dscatalog-df-pf-nu||-wwe
74ACQ244FCQR - product/74acq244fcqr?HQS=T|-nu|I-nulI-dscatalog-df—pf-null-wwe
54ACQ244PMX - product/54acq244pmx?HQS=T|-nu|I-null-dscatalog-df—pf—null-wwe
54ACQ244QMQB - product/54acq244qmqb?HQS=T|-null-null-dscatalog-df—pf—nuII-wwe
74ACQ244LCQR - product/74acq244lcqr?HQS=T|—null-nuIl-dscataIog-df-pf-null-wwe
54ACQ244QMX - product/54acq244qmx?HQS=T|—nulI-nuIl-dscatalog-df-pf-nu||-wwe
74ACQ244FCX - product/74acq244fcx?HQS=T|-null-null-dscatalog-df-pf-null-wwe
74ACTQ244LCQR - product/74actq244lcqr?HQS=T|-nu||-nu|I-dscatalog-df-pf-nulI-wwe
74ACTQ244PCQR - product/74actq244pcqr?HQS=T|-nu|I-nulI-dscatalog-df-pf-nuII-wwe
74ACTQ244PCX - product/74actq244pcx?HQS=T|-null-nuII-dscatalog-df-pf—null-wwe
74ACTQ244QCQR - product/74actq244chr?HQS=T|—nu|I-nulI-dscatalog-df-pf-nulI-wwe
74ACQ244PCX - product/74acq244pcx?HQS=T|—nu|I-nulI-dscatalog-df-pf-nuIl-wwe
74ACTQ244QCX - product/74actq244qcx?HQS=TI—null-nu|I—dscataIog-df—pf-null-wwe
74ACTQ244SCQR - product/74actq244scqr?HQS=TI-nu|I-nu|I-dscatalog-df-pf-null-wwe
74ACQ244QCX - product/74acq244qcx?HQS=Tl-nulI-nulI-dscatalog-df—pf—nuII-wwe
74ACTQ244LCX - product/74actq244lcx?HQS=T|-nu|I-nulI-dscatalog-df-pf-null-wwe
74ACTQ244SCX - product/74actq244scx?HQS=TI—nu|I-nuIl-dscatalog-df-pf-nulI-wwe
74ACTQ244FCX - product/74actq244fcx?HQS=T|-null-nulI-dscatalog-df-pf-nu||-wwe
74ACTQ244FCQR - product/74actq244fcqr?HQS=T|-nuIl-nulI-dscatalog-df-pf-nu||-wwe
74ACTQ244DCX - product/74actq244dcx?HQS=T|—null-null-dscatalog-df—pf—nuII-wwe
74ACTQ244DCQR - product/74actq244dcqr?HQS=TI-nuII-null-dscatalog-df—pf—nuII-wwe
74ACQ244QCQR - product/74acq244qcqr?HQS=T|-nu||-null-dscatalog-df-pf—nuII-wwe
74ACQ244SCX - product/74acq244scx?HQS=Tl-nulI-nulI-dscatalog-df-pf-nulI-wwe
74ACQ244SCQR - product/74acq244scqr?HQS=TI-null-null-dscatalog-df—pf—nuII-wwe
