IC Phoenix logo

Home ›  D  › D9 > DG211CJ

DG211CJ from SILICON

Fast Delivery, Competitive Price @IC-phoenix

If you need more electronic components or better pricing, we welcome any inquiry.

DG211CJ

Manufacturer: SILICON, HARRIS, MAXIM, DG, MAX, MAXIM, TI, SiL, SILICONIX, INTERSIL

SPST 4-Channel Analog Switches

Partnumber Manufacturer Quantity Availability
DG211CJ SILICON, HARRIS, MAXIM, DG, MAX, MAXIM, TI, SiL, SILICONIX, INTERSIL 11030 In Stock

Description and Introduction

SPST 4-Channel Analog Switches The DG211CJ is a quad SPST (Single-Pole Single-Throw) analog switch manufactured by **INTERSIL** (now part of Renesas Electronics). Below are its key specifications:

1. **Configuration**: Quad SPST (4 independent switches).  
2. **Switch Type**: Normally Open (NO).  
3. **Voltage Range**:  
   - **Single Supply**: +5V to +44V.  
   - **Dual Supply**: ±5V to ±20V.  
4. **On-Resistance (Ron)**: Typically **85Ω** (max 175Ω) at ±15V supply.  
5. **Charge Injection**: 10pC (typical).  
6. **Switching Time**:  
   - **Turn-On (tON)**: 300ns (max).  
   - **Turn-Off (tOFF)**: 200ns (max).  
7. **Leakage Current (Off-State)**: 1nA (max) at 25°C.  
8. **Power Supply Range**: ±4.5V to ±20V (dual), 5V to 44V (single).  
9. **Package**: 16-pin **CERDIP** (Ceramic Dual In-line Package).  
10. **Operating Temperature Range**: -40°C to +85°C.  

The DG211CJ is designed for high-voltage analog and digital switching applications.  

(Note: INTERSIL was acquired by Renesas Electronics in 2017.)

Application Scenarios & Design Considerations

SPST 4-Channel Analog Switches# Technical Documentation: DG211CJ Quad SPST Analog Switch

## 1. Application Scenarios

### 1.1 Typical Use Cases
The DG211CJ is a monolithic quad single-pole/single-throw (SPST) analog switch designed for precision signal routing applications. Each switch conducts equally well in both directions when on, and blocks signals up to the power supply rails when off.

 Primary applications include: 
-  Signal Multiplexing/Demultiplexing : Routing analog signals between multiple sources and destinations in data acquisition systems, with typical applications in 4:1 multiplexer configurations
-  Sample-and-Hold Circuits : Switching between sample and hold modes in precision measurement systems
-  Audio Signal Routing : Switching audio signals in professional audio equipment, mixers, and communication systems
-  Programmable Gain Amplifiers : Selecting different feedback resistors to change amplifier gain settings
-  Battery-Powered Systems : Power management and signal routing in portable devices due to low power consumption
-  Test and Measurement Equipment : Automated test equipment (ATE) signal routing and instrument switching

### 1.2 Industry Applications
-  Industrial Automation : PLC I/O multiplexing, sensor signal conditioning, and process control systems
-  Medical Electronics : Patient monitoring equipment, diagnostic instruments, and biomedical signal processing
-  Telecommunications : Channel switching in communication systems, modem signal routing
-  Automotive Electronics : Sensor multiplexing, diagnostic systems, and infotainment controls
-  Consumer Electronics : Audio/video switching, battery management, and user interface controls
-  Aerospace and Defense : Avionics systems, radar signal processing, and military communications

### 1.3 Practical Advantages and Limitations

 Advantages: 
-  Low Power Consumption : Typically 35μW per switch, making it suitable for battery-operated devices
-  Fast Switching Speed : Turn-on time of 175ns max, turn-off time of 145ns max
-  Low Charge Injection : 10pC typical, minimizing glitches during switching transitions
-  High Off Isolation : -80dB at 1MHz, ensuring minimal signal leakage when switches are off
-  Break-Before-Make Switching : Prevents momentary short circuits during switching transitions
-  Wide Supply Range : ±4.5V to ±20V dual supply or +9V to +44V single supply operation
-  TTL/CMOS Compatible Logic Inputs : Easy interface with digital control circuits

 Limitations: 
-  Analog Signal Range : Limited to power supply rails (cannot exceed V+ or go below V-)
-  On-Resistance Variation : 35Ω typical with ±5Ω variation across channels and temperature
-  Bandwidth Limitation : -3dB bandwidth of approximately 15MHz, limiting high-frequency applications
-  Charge Injection Effects : Can cause voltage spikes in high-impedance circuits
-  Power Supply Sequencing : Requires proper sequencing to prevent latch-up conditions
-  ESD Sensitivity : Requires proper handling and protection (typically 2000V HBM)

## 2. Design Considerations

### 2.1 Common Design Pitfalls and Solutions

 Pitfall 1: Signal Distortion at High Frequencies 
-  Problem : Signal attenuation and phase shift increase significantly above 1MHz
-  Solution : Limit signal bandwidth to 1MHz for critical applications or use higher-bandwidth switches for RF applications

 Pitfall 2: Power Supply Sequencing Issues 
-  Problem : Applying analog signals before power supplies can cause latch-up or damage
-  Solution : Implement power supply sequencing circuits or use series resistors on analog inputs

 Pitfall 3: Charge Injection in Sample-and-Hold Circuits 
-  Problem : Switching transients inject charge into holding capacitors
-  Solution : Use smaller hold capacitors with buffer amplifiers or

Alternative Part Number

  • MAX391CPE --: Quad SPST analog switch with pin-compatible DIP-16 layout and similar on-resistance, a common drop-in replacement for the DG211.
  • ADG211AKNZ --: Quad SPST analog switch functionally equivalent to the DG211, with comparable supply range and DIP-16 package.
  • HI-201HS --: Quad SPST CMOS analog switch offering similar switching characteristics and DIP-16 pinout as the DG211.
  • ADG201AKNZ --: Quad SPST analog switch in DIP-16 with comparable signal range and low leakage, suitable functional substitute for the DG211.
  • HI-201-5 --: Quad SPST CMOS analog switch in DIP-16 offering similar switching characteristics and supply range, usable as an alternative to the DG211.
  • DG211CJ+ --: Current Maxim production version of the same quad SPST switch, same electrical characteristics and package.
  • HI3-0201-5 --: Quad SPST CMOS analog switch with comparable on-resistance and switching behavior, suitable as a cross-series alternative.
  • MAX333ACPE --: Quad SPST CMOS analog switch offering comparable on-resistance and switching characteristics, suitable as a drop-in functional substitute.
  • DG211CJZ --: Second-source quad SPST CMOS analog switch with matching pin configuration and electrical characteristics.
  • MAX351CPE --: Maxim quad SPST analog switch in a comparable package, offering similar on-resistance and switching behavior.

Request Quotation

For immediate assistance, call us at +86 533 2716050 or email [email protected]

Part Number Quantity Target Price($USD) Email Contact Person
We offer highly competitive channel pricing. Get in touch for details.

Specializes in hard-to-find components chips