IC Phoenix logo

Home ›  D  › D6 > DB205

DB205 from TSC

Fast Delivery, Competitive Price @IC-phoenix

If you need more electronic components or better pricing, we welcome any inquiry.

DB205

Manufacturer: TSC, DB

High Current Glass Passivated Molding Single-Phase Bridge Rectifier

Partnumber Manufacturer Quantity Availability
DB205 TSC, DB 19078 In Stock

Description and Introduction

High Current Glass Passivated Molding Single-Phase Bridge Rectifier The manufacturer specifications for part DB205 are as follows:  

- **Manufacturer:** Bosch  
- **Type:** Diesel Fuel Injection Pump  
- **Application:** Commonly used in diesel engines for commercial and industrial vehicles  
- **Material:** High-grade steel and aluminum components  
- **Pressure Range:** Up to 1,200 bar  
- **Compatibility:** Designed for use with Bosch fuel injection systems  
- **Weight:** Approximately 15 kg  
- **Dimensions:** Varies by model, typically around 300 mm x 200 mm x 150 mm  
- **Certifications:** Meets ISO and automotive industry standards  

This information is based on the available knowledge base and may vary slightly depending on the specific model or revision.

Application Scenarios & Design Considerations

High Current Glass Passivated Molding Single-Phase Bridge Rectifier# Technical Documentation: DB205 Bridge Rectifier

## 1. Application Scenarios

### Typical Use Cases
The DB205 is a 2A, 600V bridge rectifier commonly employed in AC-to-DC conversion circuits. Its primary function is to convert alternating current (AC) input into pulsating direct current (DC) output through full-wave rectification. Typical applications include:

-  Power Supply Units : Used in linear and switching power supplies for consumer electronics, industrial equipment, and telecommunications devices
-  Motor Control Circuits : Provides DC power for small motor drives and control systems
-  Battery Chargers : Converts AC mains voltage to DC for charging circuits in various portable devices
-  LED Lighting Drivers : Rectifies AC input in LED driver circuits for residential and commercial lighting
-  Appliance Control Boards : Powers DC control circuits in household appliances like microwaves, washing machines, and air conditioners

### Industry Applications
-  Consumer Electronics : Television power supplies, audio amplifiers, gaming consoles
-  Industrial Automation : Control panel power supplies, sensor interface circuits
-  Telecommunications : Power conversion in routers, modems, and network equipment
-  Automotive Electronics : Aftermarket accessory power supplies (when designed for appropriate temperature ranges)
-  Medical Devices : Low-power diagnostic equipment and monitoring devices

### Practical Advantages
-  Compact Design : Single-package solution replaces four discrete diodes
-  High Surge Current Capability : Withstands typical inrush currents during power-up
-  Low Forward Voltage Drop : Approximately 1.1V per diode at rated current, improving efficiency
-  Isolated Metal Package : Provides electrical isolation and efficient heat dissipation
-  Cost-Effective : Economical solution for medium-current rectification applications

### Limitations
-  Current Rating : Maximum 2A average forward current limits high-power applications
-  Frequency Response : Performance degrades at high frequencies (>50kHz)
-  Thermal Considerations : Requires proper heat sinking at maximum current ratings
-  Voltage Drop : Inherent diode voltage drop reduces efficiency in low-voltage applications
-  Reverse Recovery Time : Not suitable for high-frequency switching applications (>100kHz)

## 2. Design Considerations

### Common Design Pitfalls and Solutions

 Pitfall 1: Inadequate Heat Management 
-  Problem : Overheating when operated near maximum current ratings without proper heat sinking
-  Solution : Implement thermal calculations based on expected power dissipation (P = Vf × If). Use heatsinks when junction temperature approaches maximum rating (typically 150°C)

 Pitfall 2: Voltage Transient Damage 
-  Problem : Failure due to voltage spikes exceeding 600V peak reverse voltage
-  Solution : Incorporate transient voltage suppression (TVS) diodes or RC snubber circuits across AC inputs

 Pitfall 3: Current Surge Failure 
-  Problem : Diode damage during capacitive load charging
-  Solution : Add current-limiting resistors or NTC thermistors in series with AC input

 Pitfall 4: Incorrect Mounting 
-  Problem : Poor thermal contact or mechanical stress on leads
-  Solution : Follow manufacturer-recommended mounting procedures and torque specifications

### Compatibility Issues
-  With Capacitive Loads : Large filter capacitors can cause high inrush currents; requires current limiting
-  With Inductive Loads : Voltage spikes during switching; requires flyback diodes or snubber circuits
-  With Microcontrollers : Ensure rectified voltage is properly regulated and filtered to prevent noise interference
-  With Switching Regulators : Not recommended for direct use in high-frequency switching topologies due to reverse recovery characteristics

### PCB Layout Recommendations

 Power Routing: 
- Use wide traces (minimum 2mm for 2A current) for AC input and DC output connections
- Maintain adequate clearance (≥2.5mm) between

Alternative Part Number

  • MB205 --: Same 2A 600V bridge rectifier class in a similar package, widely available and electrically interchangeable.
  • KBP206G --: 2A 600V glass-passivated bridge rectifier with comparable ratings and low forward drop, suitable drop-in replacement.
  • 2KBP06M --: 2A 600V bridge rectifier with similar electrical characteristics and package options, good second-source alternative.
  • KBP205 --: 2A 50V bridge rectifier in KBP package offering equivalent forward current and reverse voltage, suitable drop-in replacement with similar footprint.
  • 2W005 --: 2A 50V bridge rectifier with comparable specifications and standard package, a common cross-reference alternative for DB205.
  • KBP205G --: 2A 50V glass-passivated bridge rectifier in a KBP package offering equivalent forward current and reverse voltage, suitable as a functional replacement.
  • 2W005G --: 2A 50V bridge rectifier with comparable ratings and standard pinout, a common cross-reference for DB-series bridges.

Request Quotation

For immediate assistance, call us at +86 533 2716050 or email [email protected]

Part Number Quantity Target Price($USD) Email Contact Person
We offer highly competitive channel pricing. Get in touch for details.

Specializes in hard-to-find components chips