IC Phoenix logo

Home ›  D  › D6 > DB105S

DB105S from RECTRON

Fast Delivery, Competitive Price @IC-phoenix

If you need more electronic components or better pricing, we welcome any inquiry.

DB105S

Manufacturer: RECTRON, WILLAS

Single Phase 1.0 AMPS. Glass Passivated Bridge Rectifiers Voltage Range 50 to 1000 Volts Current 1.0 Amperes

Partnumber Manufacturer Quantity Availability
DB105S RECTRON, WILLAS 14580 In Stock

Description and Introduction

Single Phase 1.0 AMPS. Glass Passivated Bridge Rectifiers Voltage Range 50 to 1000 Volts Current 1.0 Amperes The part DB105S is a bridge rectifier. Here are its manufacturer specifications:

- **Type**: Single-phase bridge rectifier
- **Maximum Average Forward Current (Io)**: 1A
- **Peak Repetitive Reverse Voltage (Vrrm)**: 50V to 1000V (depending on variant)
- **Maximum RMS Voltage (Vrms)**: 35V to 700V (depending on variant)
- **Maximum DC Blocking Voltage (Vdc)**: 50V to 1000V (depending on variant)
- **Forward Voltage Drop (Vf)**: Typically 1.1V at 1A
- **Operating Temperature Range**: -55°C to +150°C
- **Package**: DBS (DIP-4)

These specifications may vary slightly based on the manufacturer. Always refer to the datasheet for precise details.

Application Scenarios & Design Considerations

Single Phase 1.0 AMPS. Glass Passivated Bridge Rectifiers Voltage Range 50 to 1000 Volts Current 1.0 Amperes# Technical Datasheet: DB105S Bridge Rectifier

## 1. Application Scenarios

### 1.1 Typical Use Cases
The DB105S is a single-phase, glass-passivated bridge rectifier designed for converting alternating current (AC) to direct current (DC) in low-power applications. Its compact construction and reliable performance make it suitable for:

*  AC-to-DC Power Conversion : Primary use in power supply input stages for small electronic devices, converting mains AC (typically 50/60 Hz) to pulsating DC for subsequent filtering and regulation.
*  Signal Demodulation : Can be used in simple amplitude modulation (AM) detector circuits due to its rectification properties.
*  Polarity Protection : Employed in circuits to ensure correct DC polarity regardless of AC input connection.
*  Battery Chargers : Found in low-current charger circuits for consumer electronics.

### 1.2 Industry Applications
*  Consumer Electronics : Power supplies for routers, set-top boxes, small audio amplifiers, LED drivers, and appliance control boards.
*  Industrial Controls : Low-power sensor interfaces, relay drivers, and logic power supplies within control panels.
*  Telecommunications : Power conversion in customer premises equipment (CPE) like modems and network switches.
*  Lighting : Driver circuits for LED bulbs and fixtures.

### 1.3 Practical Advantages and Limitations

 Advantages: 
*  Compact Form Factor : The DB-S package (SIP-4) offers a space-saving solution compared to discrete diode arrangements.
*  Simplified Assembly : Reduces component count and PCB assembly complexity versus four discrete diodes.
*  Good Surge Handling : Glass-passivated junctions provide reliable performance against voltage transients.
*  Cost-Effective : Economical solution for low-to-medium current rectification needs.
*  Electrical Isolation : The plastic package provides basic isolation, simplifying thermal and mounting considerations.

 Limitations: 
*  Current Capacity : Limited to 1.0 A average forward current, unsuitable for high-power applications.
*  Voltage Drop : Typical forward voltage of 1.0 V per diode (2.0 V total in conduction path) leads to power dissipation and reduced efficiency in very low-voltage circuits.
*  Frequency Response : Designed for line frequency (50/60 Hz) operation; performance degrades significantly at high frequencies (>10 kHz).
*  Thermal Management : Requires consideration of heat dissipation at maximum load currents.

## 2. Design Considerations

### 2.1 Common Design Pitfalls and Solutions

 Pitfall 1: Inadequate Current Derating 
*  Problem : Operating at or near the maximum rated current (1.0 A) without derating for temperature.
*  Solution : Derate current based on ambient temperature. For reliable operation, design for ≤0.7 A continuous current at 40°C ambient. Use thermal calculations or heatsinking if higher currents are necessary.

 Pitfall 2: Ignoring Inrush Current 
*  Problem : Cold-start inrush currents into capacitive loads can exceed the device's surge rating (IFSM).
*  Solution : Implement inrush current limiting using NTC thermistors, series resistors, or active limiting circuits. Ensure the calculated inrush current stays below the 30 A non-repetitive peak surge rating.

 Pitfall 3: Reverse Voltage Margin 
*  Problem : Operating near the maximum repetitive peak reverse voltage (VRRM = 1000 V) without safety margin.
*  Solution : Select a device with a VRRM at least 20-30% higher than the peak AC input voltage. For 230VAC mains (≈325V peak), the DB105S provides sufficient margin.

 Pitfall 4: Poor Thermal Design 
*  Problem : Mounting on small PCB pads without adequate copper area for heat dissipation.
*  Solution : Incorporate thermal relief pads connected

Alternative Part Number

  • MB105S --: Same 1A 600V single-phase bridge rectifier in a similar SMD package, widely available and a direct functional replacement.
  • DF06S --: 1A 600V bridge rectifier in a similar surface-mount package with comparable ratings and pinout.
  • KBP06 --: 1A 600V bridge rectifier with equivalent electrical ratings, though in a through-hole package, usable where board space allows.
  • B10S --: 1A 600V single-phase bridge rectifier with comparable ratings and footprint, a common cross-reference for DB105S.
  • KBP106 --: 1A 600V bridge rectifier with equivalent voltage and current ratings; through-hole package but electrically interchangeable.
  • MB105 --: 1A 600V bridge rectifier in a similar package with equivalent electrical ratings, widely available and a common drop-in replacement.
  • KBP105G --: 1A 600V glass-passivated bridge rectifier offering comparable forward current and reverse voltage, suitable for the same rectification role.
  • DF06M --: 1A 600V bridge rectifier with similar specifications and a compact package, usable as an alternative where board space allows.

Request Quotation

For immediate assistance, call us at +86 533 2716050 or email [email protected]

Part Number Quantity Target Price($USD) Email Contact Person
We offer highly competitive channel pricing. Get in touch for details.

Specializes in hard-to-find components chips