IC Phoenix logo

Home ›  D  › D37 > DTC123JKA

DTC123JKA from ROHM

Fast Delivery, Competitive Price @IC-phoenix

If you need more electronic components or better pricing, we welcome any inquiry.

DTC123JKA

Manufacturer: ROHM

NPN 100mA 50V Digital Transistors (Bias Resistor Built-in Transistors)

Partnumber Manufacturer Quantity Availability
DTC123JKA ROHM 6360 In Stock

Description and Introduction

NPN 100mA 50V Digital Transistors (Bias Resistor Built-in Transistors) The DTC123JKA is a digital transistor manufactured by ROHM. Below are its specifications:  

- **Type**: Digital transistor (built-in resistor)  
- **Polarity**: PNP  
- **Maximum Collector-Base Voltage (VCBO)**: -50V  
- **Maximum Collector-Emitter Voltage (VCEO)**: -50V  
- **Maximum Emitter-Base Voltage (VEBO)**: -5V  
- **Collector Current (IC)**: -100mA  
- **Base Current (IB)**: -5mA  
- **Total Power Dissipation (PT)**: 200mW  
- **Junction Temperature (Tj)**: 150°C  
- **Storage Temperature (Tstg)**: -55°C to +150°C  
- **Resistor Values**:  
  - **R1 (Base Resistor)**: 10kΩ  
  - **R2 (Base-Emitter Resistor)**: 10kΩ  
- **Package**: SOT-23  

These specifications are based on ROHM's official datasheet for the DTC123JKA.

Application Scenarios & Design Considerations

NPN 100mA 50V Digital Transistors (Bias Resistor Built-in Transistors)# Technical Datasheet: DTC123JKA Digital Transistor

## 1. Application Scenarios

### 1.1 Typical Use Cases
The DTC123JKA is a  digital transistor (bias resistor built-in transistor)  primarily employed as an interface device between low-current control signals and higher-current loads. Its integrated base-emitter and base-collector resistors simplify circuit design by reducing external component count.

 Primary applications include: 
-  Signal Inversion/Amplification : Converting weak microcontroller GPIO signals (3.3V/5V) into sufficient drive currents for relays, LEDs, or small motors.
-  Load Switching : Acting as a solid-state switch for loads up to 100mA, such as indicator LEDs, buzzers, or small solenoids.
-  Level Shifting : Interfacing between different voltage domains in mixed-voltage systems.
-  Input Buffering : Providing input protection and signal conditioning for sensitive IC inputs.

### 1.2 Industry Applications
-  Consumer Electronics : Remote controls, smart home devices, and portable electronics where space and component count are critical.
-  Automotive Electronics : Non-critical switching applications in body control modules, lighting controls, and sensor interfaces (within specified temperature ranges).
-  Industrial Control : PLC I/O modules, sensor interfaces, and indicator circuits where reliability and simplicity are valued.
-  Telecommunications : Line interface circuits and status indication in networking equipment.

### 1.3 Practical Advantages and Limitations

 Advantages: 
-  Space Efficiency : Eliminates two discrete resistors, reducing PCB footprint by approximately 60% compared to discrete implementations.
-  Improved Reliability : Fewer solder joints and components decrease potential failure points.
-  Simplified Assembly : Reduces pick-and-place operations and bill-of-materials complexity.
-  Consistent Performance : Tight resistor tolerances (typically ±30%) ensure predictable switching characteristics across production lots.
-  ESD Protection : Integrated resistors provide some electrostatic discharge protection for the base-emitter junction.

 Limitations: 
-  Fixed Biasing : Built-in resistors (R1=10kΩ, R2=10kΩ) cannot be adjusted for optimal performance across all operating conditions.
-  Limited Current Handling : Maximum collector current (IC) of 100mA restricts use to small loads.
-  Thermal Constraints : Power dissipation limited to 200mW requires careful thermal management in high-ambient-temperature environments.
-  Frequency Response : Not suitable for high-frequency applications (>10MHz) due to internal parasitic capacitance.

## 2. Design Considerations

### 2.1 Common Design Pitfalls and Solutions

 Pitfall 1: Inadequate Base Drive Current 
-  Problem : Assuming the digital transistor will switch fully with minimal base current.
-  Solution : Calculate required base current using IB = (VIN - VBE) / (R1 + (hFE × R2)). For 5V input, ensure IB > 0.5mA for reliable saturation.

 Pitfall 2: Thermal Runaway in Linear Mode 
-  Problem : Operating in active region for extended periods without thermal considerations.
-  Solution : Use only for switching applications. If linear operation is unavoidable, implement external thermal monitoring or derate power dissipation by 50% above 25°C.

 Pitfall 3: Inductive Load Switching Without Protection 
-  Problem : Switching inductive loads (relays, solenoids) causing voltage spikes that exceed VCEO.
-  Solution : Implement flyback diodes across inductive loads and consider adding snubber circuits for high-inductance loads.

### 2.2 Compatibility Issues with Other Components

 Microcontroller Interfaces: 
-  3.3V MCUs : May not provide sufficient VBE to turn on transistor reliably. Verify VOH(min) > 2.0V or use level shifter.
-  

Alternative Part Number

  • MMUN2211LT1G --: NPN digital transistor with built-in bias resistors (10k/10k), functionally similar to the DTC123JKA and widely available.
  • PDTC123JT --: NPN resistor-equipped transistor with comparable 2.2k/4.7k bias network, suitable direct replacement in switching applications.
  • KRC102S --: NPN digital transistor with integrated bias resistors, commonly used as an alternative to ROHM DTC-series parts.
  • MMUN2213LT1G --: NPN bias resistor transistor with matching 2.2k/47k resistor values, suitable direct replacement.
  • KRC103S --: NPN digital transistor with integrated 2.2k/47k bias resistors, same switching function and package style.

Request Quotation

For immediate assistance, call us at +86 533 2716050 or email [email protected]

Part Number Quantity Target Price($USD) Email Contact Person
We offer highly competitive channel pricing. Get in touch for details.

Specializes in hard-to-find components chips