IC Phoenix logo

Home ›  D  › D37 > DTC114TM

DTC114TM from ROHM

Fast Delivery, Competitive Price @IC-phoenix

If you need more electronic components or better pricing, we welcome any inquiry.

DTC114TM

Manufacturer: ROHM, DIODES

NPN 100mA 50V Digital Transistors (Bias Resistor Built-in Transistors)

Partnumber Manufacturer Quantity Availability
DTC114TM ROHM, DIODES 49750 In Stock

Description and Introduction

NPN 100mA 50V Digital Transistors (Bias Resistor Built-in Transistors) The DTC114TM is a digital transistor manufactured by ROHM. Below are its key specifications:  

- **Type**: NPN digital transistor with built-in resistors  
- **Maximum Collector-Base Voltage (VCBO)**: 50V  
- **Maximum Collector-Emitter Voltage (VCEO)**: 50V  
- **Maximum Emitter-Base Voltage (VEBO)**: 5V  
- **Maximum Collector Current (IC)**: 100mA  
- **Power Dissipation (PD)**: 200mW  
- **DC Current Gain (hFE)**: 100 (min) to 400 (max)  
- **Built-in Resistors**:  
  - Base resistor (R1): 10kΩ  
  - Base-emitter resistor (R2): 10kΩ  
- **Package**: SOT-416 (SC-75)  

These specifications are based on ROHM's official datasheet for the DTC114TM.

Application Scenarios & Design Considerations

NPN 100mA 50V Digital Transistors (Bias Resistor Built-in Transistors)# Technical Documentation: DTC114TM Digital Transistor

## 1. Application Scenarios

### 1.1 Typical Use Cases
The DTC114TM is a digital transistor (bias resistor-equipped transistor) primarily used for  interface switching and signal inversion  in low-power digital circuits. Its integrated base-emitter resistor (R1) and base resistor (R2) simplify circuit design by eliminating external discrete resistors.

 Primary functions include: 
*    Logic Level Inversion:  Converting a high logic signal to low, or vice versa, in microcontroller and logic gate interfaces.
*    Load Switching:  Driving small inductive or resistive loads (e.g., relays, LEDs, small motors) directly from a microcontroller GPIO pin.
*    Signal Buffering/Isolation:  Isolating a sensitive control circuit (like an MCU) from a higher-current or higher-voltage load circuit.
*    Pull-up/Pull-down Function:  The internal resistors provide a defined state for open-collector or open-drain configurations.

### 1.2 Industry Applications
This component is ubiquitous in cost-sensitive, space-constrained, and high-volume applications.

*    Consumer Electronics:  Remote controls, smart home devices, toys, and audio equipment for button input sensing and LED driving.
*    Automotive Electronics:  Non-critical body control modules (e.g., interior lighting control, simple sensor interfacing) where environmental conditions are mild.
*    Industrial Control:  PLC I/O modules, sensor interfaces, and optocoupler replacements for low-speed signal conditioning.
*    Computer Peripherals:  Keyboard/mouse encoders, printer head driving, and fan control circuits.
*    Telecommunications:  Line interface circuits and ringing signal detection in low-power telephony equipment.

### 1.3 Practical Advantages and Limitations

 Advantages: 
*    Board Space Savings:  Eliminates two external SMD resistors, reducing PCB footprint and assembly cost.
*    Simplified Design & BOM:  Reduces component count, simplifying schematic and procurement.
*    Improved Reliability:  Fewer solder joints increase manufacturing yield and long-term reliability.
*    Stable Bias:  Integrated resistors provide consistent biasing, reducing performance variation.
*    ESD Protection:  The internal resistors offer a degree of protection against electrostatic discharge on the base terminal.

 Limitations: 
*    Fixed Bias Ratio:  The resistor ratio (R1/R2) is fixed by the manufacturer (typically 10kΩ/10kΩ for DTC114TM). Designers cannot optimize it for specific gain or switching speed requirements.
*    Limited Current Capability:  Collector current (`Ic`) is typically limited to 100mA. It is unsuitable for driving high-power loads.
*    Speed Constraints:  The internal base resistor limits the base current, which can slow down switching speeds compared to a discrete transistor with an optimized drive circuit. Not suitable for high-frequency (>1MHz) switching.
*    Thermal Considerations:  The small SOT-23 package has limited power dissipation (~200mW). Sustained high-current operation requires thermal analysis.

## 2. Design Considerations

### 2.1 Common Design Pitfalls and Solutions
| Pitfall | Consequence | Solution |
| :--- | :--- | :--- |
|  Overlooking `Ic` Limit  | Transistor saturation, excessive heating, failure. | Calculate load current and ensure it is below the maximum `Ic` (100mA). Include a safety margin (e.g., 70-80mA max). |
|  Insufficient Base Drive  | Transistor operates in linear region, causing high `Vce(sat)` and overheating. | Verify the driving source (e.g., MCU GPIO) can provide enough voltage/current to overcome `Vbe` and the internal 10kΩ base resistor (`R2`). |
|  Omitting

Alternative Part Number

  • MMUN2211LT1G --: NPN digital transistor with built-in 10k base resistor and 10k base-emitter resistor, functionally equivalent to the DTC114T series and widely available.
  • PDTC114TT,215 --: NPN resistor-equipped transistor with the same 10k/10k bias resistor configuration, direct functional replacement in SOT-23 package.
  • KRC102S --: NPN digital transistor with integrated 10k base resistor, suitable as a cross-manufacturer substitute for the DTC114T in switching applications.
  • PDTC114TT --: NPN digital transistor with built-in 10k base resistor and 10k base-emitter resistor, same SOT-23 package and equivalent electrical characteristics.

Request Quotation

For immediate assistance, call us at +86 533 2716050 or email [email protected]

Part Number Quantity Target Price($USD) Email Contact Person
We offer highly competitive channel pricing. Get in touch for details.

Specializes in hard-to-find components chips