IC Phoenix logo

Home ›  D  › D37 > DTA144EKAT146

DTA144EKAT146 from ROHM

Fast Delivery, Competitive Price @IC-phoenix

If you need more electronic components or better pricing, we welcome any inquiry.

DTA144EKAT146

Manufacturer: ROHM

PNP -100mA -50V Digital Transistors

Partnumber Manufacturer Quantity Availability
DTA144EKAT146 ROHM 216000 In Stock

Description and Introduction

PNP -100mA -50V Digital Transistors The part **DTA144EKAT146** is a **Digital Transistor (Bias Resistor Built-in Transistor)** manufactured by **ROHM Semiconductor**.  

### **Key Specifications:**  
- **Type:** NPN Digital Transistor  
- **Configuration:** Built-in bias resistors (R1 and R2)  
- **Collector Current (Ic):** 100mA  
- **Collector-Emitter Voltage (VCEO):** 50V  
- **Emitter-Base Voltage (VEBO):** 5V  
- **Power Dissipation (Pd):** 150mW  
- **Resistor Values:**  
  - **R1 (Base Resistor):** 10kΩ  
  - **R2 (Base-Emitter Resistor):** 10kΩ  
- **Package:** SOT-346 (SC-59)  

This device is designed for switching and amplification in digital circuits, reducing external component count.  

For exact details, refer to the official **ROHM datasheet**.

Application Scenarios & Design Considerations

PNP -100mA -50V Digital Transistors# Technical Documentation: DTA144EKAT146 Digital Transistor

## 1. Application Scenarios

### 1.1 Typical Use Cases
The DTA144EKAT146 is a  digital transistor (bias resistor built-in transistor)  primarily designed for  low-power switching and amplification  in compact electronic circuits. Its integrated bias resistors make it particularly suitable for:

*  Interface Circuits : Level shifting between microcontrollers (3.3V/5V) and higher voltage peripherals
*  Load Switching : Direct drive of small relays, LEDs, or buzzers from digital I/O pins
*  Signal Inversion : Simple logic inversion in digital circuits without additional discrete components
*  Impedance Buffering : Isolation between sensitive control circuits and noisy load sections

### 1.2 Industry Applications
*  Consumer Electronics : Remote controls, smart home devices, portable electronics where board space is constrained
*  Automotive Electronics : Non-critical switching applications in infotainment and comfort systems
*  Industrial Control : PLC input/output modules, sensor signal conditioning
*  Telecommunications : Signal routing in low-frequency communication modules

### 1.3 Practical Advantages and Limitations

 Advantages: 
*  Space Efficiency : Eliminates two external resistors (typically 10kΩ base and 10kΩ base-emitter), reducing PCB footprint by approximately 60%
*  Simplified Assembly : Fewer components reduce pick-and-place operations and potential assembly errors
*  Improved Reliability : Reduced solder joints and component interconnections enhance overall circuit reliability
*  Consistent Performance : Factory-trimmed internal resistors ensure stable bias conditions across production lots
*  Cost Reduction : Lower total component count and assembly time in high-volume production

 Limitations: 
*  Fixed Bias Configuration : Internal resistor values (R1=10kΩ, R2=10kΩ) cannot be adjusted for specific gain requirements
*  Power Handling : Limited to 100mA continuous collector current, unsuitable for high-power applications
*  Frequency Response : Maximum transition frequency of 250MHz restricts use in high-speed switching (>10MHz) applications
*  Thermal Constraints : Small SOT-346 package has limited thermal dissipation capability (150mW maximum power dissipation)

## 2. Design Considerations

### 2.1 Common Design Pitfalls and Solutions

 Pitfall 1: Overcurrent Conditions 
*  Problem : Exceeding 100mA collector current causes thermal runaway and permanent damage
*  Solution : Implement external current limiting for loads with potential surge currents (e.g., capacitive loads)

 Pitfall 2: Insufficient Drive Current 
*  Problem : Microcontroller GPIO pins (especially at 3.3V) may not provide adequate base current for saturation
*  Solution : Verify base current calculation: Ib = (Voh - Vbe) / (R1 + R2 × hFE) where Voh is output high voltage

 Pitfall 3: Switching Speed Limitations 
*  Problem : Slow turn-off times when switching inductive loads
*  Solution : Add external pull-down resistor (1-10kΩ) between base and emitter to accelerate charge removal

### 2.2 Compatibility Issues with Other Components

 Microcontroller Interfaces: 
*  3.3V Systems : Ensure Voh(min) > 2.0V for proper transistor saturation (check specific microcontroller specifications)
*  5V Systems : Generally compatible, but may require current limiting resistor for GPIO protection

 Load Compatibility: 
*  Inductive Loads : Always use flyback diode across relay/coil to protect transistor from voltage spikes
*  LED Driving : Include series current-limiting resistor despite transistor current regulation capability

 Mixed Voltage Systems: 
* The 50V VCEO rating provides adequate headroom for 12V/24V systems interfaced with 3.3V/5V

Alternative Part Number

  • MMUN2214LT1G --: PNP digital transistor with built-in 10k base and 47k emitter resistors, same SOT-23 package and equivalent electrical function as the original.
  • PDTA144ET,215 --: PNP resistor-equipped transistor with 47k/10k bias resistors in SOT-23, a direct functional replacement for the DTA144E series.
  • DDTA144ECA-7-F --: PNP pre-biased transistor with 47k/10k resistors in SOT-23, matching the original's bias resistor values and switching behavior.
  • MMUN2211LT1G --: PNP digital transistor with built-in 10k/10k bias resistors, functionally equivalent to the DTA144E series and widely available.
  • RN2402TE85LF --: PNP transistor with integrated 10k/10k bias resistors in SOT-23, direct functional replacement for DTA144E applications.

Request Quotation

For immediate assistance, call us at +86 533 2716050 or email [email protected]

Part Number Quantity Target Price($USD) Email Contact Person
We offer highly competitive channel pricing. Get in touch for details.

Specializes in hard-to-find components chips