IC Phoenix logo

Home ›  D  › D37 > DTA143ZKA

DTA143ZKA from 蓝箭

Fast Delivery, Competitive Price @IC-phoenix

If you need more electronic components or better pricing, we welcome any inquiry.

DTA143ZKA

Manufacturer: 蓝箭, ROHM, ROHM

PNP -100mA -50V Digital Transistors (Bias Resistor Built-in Transistors)

Partnumber Manufacturer Quantity Availability
DTA143ZKA 蓝箭, ROHM, ROHM 60433 In Stock

Description and Introduction

PNP -100mA -50V Digital Transistors (Bias Resistor Built-in Transistors) The DTA143ZKA is a digital transistor manufactured by ROHM. Below are its key specifications:  

- **Type**: PNP Digital Transistor (with built-in resistors)  
- **Maximum Collector-Base Voltage (VCBO)**: -50V  
- **Maximum Collector-Emitter Voltage (VCEO)**: -50V  
- **Maximum Emitter-Base Voltage (VEBO)**: -5V  
- **Continuous Collector Current (IC)**: -100mA  
- **Total Power Dissipation (PT)**: 150mW  
- **DC Current Gain (hFE)**: 56 (min) to 112 (max) at VCE = -5V, IC = -2mA  
- **Built-in Resistors**:  
  - R1 (Base resistor): 4.7kΩ  
  - R2 (Base-Emitter resistor): 4.7kΩ  
- **Operating Temperature Range**: -55°C to +150°C  
- **Package**: SOT-346 (SC-59)  

This information is sourced from ROHM's official datasheet for the DTA143ZKA.

Application Scenarios & Design Considerations

PNP -100mA -50V Digital Transistors (Bias Resistor Built-in Transistors)# Technical Datasheet: DTA143ZKA Digital Transistor

## 1. Application Scenarios

### 1.1 Typical Use Cases
The DTA143ZKA is a digital transistor (bias resistor built-in transistor) primarily designed for  low-power switching and amplification  in compact electronic circuits. Its integrated base-emitter and base-collector resistors make it particularly suitable for:

-  Interface Circuits : Level shifting between microcontrollers (3.3V/5V) and higher voltage peripherals
-  Load Switching : Direct drive of small relays, LEDs, or other low-current loads (<100mA)
-  Signal Inversion : Inverter/buffer stages in logic circuits where discrete transistor-resistor networks would occupy excessive board space
-  Input Protection : Input stage protection for digital ICs, providing current limiting and voltage clamping

### 1.2 Industry Applications
-  Consumer Electronics : Remote controls, smart home devices, portable electronics where board space is premium
-  Automotive Electronics : Non-critical switching functions in infotainment systems, lighting controls (excluding safety-critical applications)
-  Industrial Control : PLC input/output modules, sensor interface circuits, panel controls
-  Telecommunications : Line interface circuits, modem controls, peripheral switching

### 1.3 Practical Advantages and Limitations

 Advantages: 
-  Space Efficiency : Eliminates need for two external resistors (typically 4.7kΩ base-emitter, 10kΩ base-collector), reducing component count by 66%
-  Improved Reliability : Reduced solder joints and component interconnections enhance overall circuit reliability
-  Simplified Design : Predetermined bias conditions simplify circuit design and reduce calculation requirements
-  Consistent Performance : Tight resistor tolerances (±30%) ensure more predictable switching characteristics across production batches
-  ESD Protection : Integrated resistors provide limited ESD protection to the base-emitter junction

 Limitations: 
-  Fixed Configuration : Cannot optimize resistor values for specific applications; limited to built-in 4.7kΩ/10kΩ combination
-  Power Handling : Maximum collector current of 100mA restricts use to low-power applications only
-  Thermal Considerations : Small SOT-346 package has limited thermal dissipation capability (150mW maximum)
-  Frequency Response : Not suitable for high-frequency applications (>100MHz) due to internal parasitics
-  Voltage Constraints : Maximum VCEO of 50V limits high-voltage applications

## 2. Design Considerations

### 2.1 Common Design Pitfalls and Solutions

 Pitfall 1: Overcurrent Conditions 
-  Problem : Exceeding 100mA collector current causes thermal runaway and permanent damage
-  Solution : Implement external current limiting for loads exceeding 50mA, or use parallel devices with balancing resistors

 Pitfall 2: Inadequate Base Drive 
-  Problem : Microcontroller GPIO pins (especially 3.3V systems) may not provide sufficient base current for saturation
-  Solution : Verify base current calculation: IB = (VOH - VBE) / (R1 + R2 × hFE) where R1=4.7kΩ, R2=10kΩ

 Pitfall 3: Inductive Load Switching 
-  Problem : Switching inductive loads without protection causes voltage spikes exceeding VCEO
-  Solution : Add flyback diode across inductive loads or snubber networks for faster switching

 Pitfall 4: Thermal Management 
-  Problem : Continuous operation at maximum ratings leads to premature failure
-  Solution : Derate power dissipation by 30-50% for reliable operation, add thermal vias for SMT applications

### 2.2 Compatibility Issues with Other Components

 Microcontroller Interfaces: 
-  3.3V Systems : May require level shifting if driving higher voltage loads; ensure VOH

Alternative Part Number

  • PDTA143ZT --: PNP digital transistor with built-in 4.7k base and 47k emitter resistors, same R1/R2 ratio and SOT-23 package, direct functional equivalent.
  • MMUN2133LT1G --: PNP bias resistor transistor with 4.7k/47k resistor network in SOT-23, matches the DTA143Z electrical configuration.
  • RN2303 --: PNP digital transistor with 4.7k/47k built-in resistors in SOT-23, suitable drop-in replacement for switching and interface circuits.
  • DDTA143ZCA --: PNP pre-biased transistor with 4.7k base and 47k shunt resistors, functionally equivalent to the DTA143ZKA for switching applications.

Request Quotation

For immediate assistance, call us at +86 533 2716050 or email [email protected]

Part Number Quantity Target Price($USD) Email Contact Person
We offer highly competitive channel pricing. Get in touch for details.

Specializes in hard-to-find components chips