IC Phoenix logo

Home ›  D  › D28 > DS2196LN

DS2196LN from DS,MAXIM - Dallas Semiconductor

Fast Delivery, Competitive Price @IC-phoenix

If you need more electronic components or better pricing, we welcome any inquiry.

DS2196LN

Manufacturer: DS, DALLAS

T1 Dual Framer LIU

Partnumber Manufacturer Quantity Availability
DS2196LN DS, DALLAS 1810 In Stock

Description and Introduction

T1 Dual Framer LIU The DS2196LN is a part manufactured by DALLAS (now part of Maxim Integrated). It is a T1/E1/J1 Short Haul LIU (Line Interface Unit) with integrated jitter attenuators. Key specifications include:

- **Interface Standards**: Compliant with T1 (1.544 Mbps), E1 (2.048 Mbps), and J1 line rates.
- **Jitter Attenuation**: Integrated jitter attenuators for both transmit and receive paths.
- **Package**: 28-pin PLCC (Plastic Leaded Chip Carrier).
- **Power Supply**: Operates on a single +5V supply.
- **Features**: Includes line build-out (LBO) control, adaptive equalization, and loss-of-signal (LOS) detection.
- **Temperature Range**: Commercial (0°C to +70°C) and industrial (-40°C to +85°C) options available.

This part is designed for telecommunications applications requiring robust line interface functionality.

Application Scenarios & Design Considerations

T1 Dual Framer LIU# DS2196LN Technical Documentation

## 1. Application Scenarios

### Typical Use Cases
The DS2196LN is a high-performance  serial interface transceiver  primarily employed in  digital communication systems  requiring robust data transmission capabilities. Typical implementations include:

-  RS-232/RS-485 serial communication interfaces  in industrial control systems
-  Modem and data terminal equipment  (DTE) connections
-  Point-of-sale terminals  and  industrial automation controllers 
-  Embedded systems  requiring legacy serial communication support
-  Telecommunications equipment  for maintenance and configuration ports

### Industry Applications
 Industrial Automation : The component excels in  harsh industrial environments  where electrical noise immunity is critical. It's commonly deployed in:
- PLC (Programmable Logic Controller) communication modules
- Motor drive control systems
- Sensor network gateways
- Factory floor communication hubs

 Telecommunications : Used in  network equipment  for:
- Base station configuration interfaces
- Router and switch console ports
- Network management system interfaces

 Consumer Electronics : Despite being a legacy interface, it finds use in:
- Industrial-grade POS systems
- Medical device configuration ports
- Test and measurement equipment

### Practical Advantages and Limitations

 Advantages: 
-  Robust noise immunity  through differential signaling
-  Extended communication distance  up to 1200 meters at lower data rates
-  Multi-drop capability  supporting up to 32 connected devices
-  Wide operating voltage range  (4.5V to 5.5V)
-  ESD protection  up to ±15kV (Human Body Model)

 Limitations: 
-  Lower data rates  compared to modern interfaces (max 10Mbps)
-  Higher power consumption  than contemporary alternatives
-  Limited to half-duplex operation  without additional components
-  Requires external termination resistors  for proper impedance matching

## 2. Design Considerations

### Common Design Pitfalls and Solutions

 Pitfall 1: Improper Termination 
-  Issue : Signal reflections causing data corruption
-  Solution : Implement  120Ω termination resistors  at both ends of the transmission line

 Pitfall 2: Ground Loops 
-  Issue : Common-mode noise affecting signal integrity
-  Solution : Use  isolated power supplies  or  galvanic isolation  between systems

 Pitfall 3: Incorrect Biasing 
-  Issue : Undefined bus state during idle conditions
-  Solution : Implement  fail-safe biasing network  with pull-up/pull-down resistors

### Compatibility Issues

 Voltage Level Conflicts: 
- The DS2196LN operates at  5V logic levels , requiring level shifters when interfacing with 3.3V systems
-  RS-485 standard compliance  ensures compatibility with other industry-standard transceivers

 Timing Considerations: 
-  Driver enable/disable times  must be coordinated with microcontroller UART timing
-  Bus contention  can occur if multiple drivers are enabled simultaneously

### PCB Layout Recommendations

 Power Supply Decoupling: 
- Place  0.1μF ceramic capacitors  within 5mm of VCC pins
- Additional  10μF bulk capacitor  for power supply stability

 Signal Routing: 
- Route  A and B differential pairs  as closely coupled traces
- Maintain  consistent impedance  throughout the transmission line
- Keep  RS-485 traces away from  noisy digital signals and power supplies

 Grounding Strategy: 
- Implement  single-point grounding  for analog and digital sections
- Use  ground planes  for improved noise immunity
- Separate  analog and digital grounds  with a single connection point

## 3. Technical Specifications

### Key Parameter Explanations

 Electrical Characteristics: 
-  Supply Voltage : 4.5V to

Alternative Part Number

  • BCM5221KPB --: Similar dual-port Ethernet transceiver function with comparable interface support, suitable as a functional replacement in networking designs.
  • KSZ8895MQ --: Integrated 5-port Ethernet switch/transceiver offering similar networking functionality and widely available as an alternative.
  • DP83848IVV --: Single-port Ethernet PHY transceiver with robust industrial support, usable where the original transceiver function is required.
  • BCM5221 --: Similar Ethernet transceiver/PHY function in the same application class, widely available as a functional substitute.
  • KSZ8041NL --: Single-port 10/100 Ethernet PHY with comparable interface and supply requirements, suitable as a drop-in functional replacement.
  • DP83848 --: Industry-standard 10/100 Ethernet PHY offering similar functionality and pin-compatible options for legacy designs.

Request Quotation

For immediate assistance, call us at +86 533 2716050 or email [email protected]

Part Number Quantity Target Price($USD) Email Contact Person
We offer highly competitive channel pricing. Get in touch for details.

Specializes in hard-to-find components chips