IC Phoenix
 
Home ›  VV4 > VNB28N04,"OMNIFET" FULLY AUTOPROTECTED POWER MOSFET
VNB28N04 Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
VNB28N04STN/a1500avai"OMNIFET" FULLY AUTOPROTECTED POWER MOSFET


VNB28N04 ,"OMNIFET" FULLY AUTOPROTECTED POWER MOSFETELECTRICAL CHARACTERISTICS (continued)DYNAMICSymbol Parameter Test Conditions Min. Typ. Max. Unitg ..
VNB35N07 ,"OMNIFET" FULLY AUTOPROTECTED POWER MOSFETELECTRICAL CHARACTERISTICS (continued)SWITCHING (** )Symbol Parameter Test Conditions Min. Typ. Max ..
VNB35N07-E , ”OMNIFET”: FULLY AUTOPROTECTED POWER MOSFET
VNB35NV04 ,"OMNIFET II": FULLY AUTOPROTECTED POWER MOSFETELECTRICAL CHARACTERISTICS (continued) (T =25°C, unless otherwise specified)jDYNAMICSymbol Paramete ..
VNB49N04 ,"OMNIFET" FULLY AUTOPROTECTED POWER MOSFETFEATURESDuring normal operation, the INPUT pin is junction temperature may reach theelectrically co ..
VND05B ,DOUBLE CHANNEL HIGH SIDE SMART POWER SOLID STATE RELAYELECTRICAL CHARACTERISTICS (8VWE2408 , 2.4GHz Single Chip FM Transceiver
WE9140A , TONE/PULSE SWITCHABLE DIALER WITH REDIAL
WE9140A , TONE/PULSE SWITCHABLE DIALER WITH REDIAL
WE9140G , TONE/PULSE SWITCHABLE DIALER WITH REDIAL
WE9140J , TONE/PULSE SWITCHABLE DIALER WITH REDIAL
WE9142 , 10-MEMORY TONE/PULSE SWITCHABLE DIALER


VNB28N04
"OMNIFET" FULLY AUTOPROTECTED POWER MOSFET
VNP28N04FI
VNB28N04/VNV28N04

”OMNIFET”:
FULLY AUTOPROTECTED POWER MOSFET
June 1998
BLOCK DIAGRAM(∗)
TYPE Vclamp RDS(on) Ilim

VNP28N04FI
VNB28N04
VNV28N04VVV
0.035Ω
0.035 Ω
0.035ΩAAA LINEAR CURRENT LIMITATION THERMAL SHUT DOWN SHORT CIRCUIT PROTECTION INTEGRATED CLAMP LOW CURRENT DRAWN FROM INPUT PIN DIAGNOSTIC FEEDBACK THROUGH INPUT
PIN ESD PROTECTION DIRECT ACCESS TO THE GATE OF THE
POWER MOSFET (ANALOG DRIVING) COMPATIBLE WITH STANDARD POWER
MOSFET
DESCRIPTION

The VNP28N04FI, VNB28N04 and VNV28N04
are monolithic devices made using
STMicroelectronics VIPower M0 Technology,
intended for replacement of standard power
MOSFETSin DCto 50 KHz applications. Built-in
thermal shut-down, linear current limitation and
overvoltage clamp protect the chip in harsh
enviroments.
Fault feedback can be detectedby monitoring the
voltageat the input pin.
PowerSO-10
23
D2PAK
TO-263
ISOWATT220

(∗) PowerSO-10Pin Configuration: INPUT= 6,7,8,9,10;SOURCE= 1,2,4,5; DRAIN= TAB
1/13
ABSOLUTE MAXIMUM RATING
Symbol Parameter Value Unit
PowerSO-10
D2PAK
ISOWATT220

VDS Drain-source Voltage (Vin=0) Internally Clamped V
Vin Input Voltage 18 V Drain Current Internally Limited A Reverse DC Output Current -28 A
Vesd Electrostatic Discharge (C= 100 pF, R=1.5 KΩ) 2000 V
Ptot Total DissipationatTc =25o C83 34 W Operating Junction Temperature Internally Limited oC Case Operating Temperature Internally Limited oC
Tstg Storage Temperature -55to 150 oC
THERMAL DATA
ISOWATT220 PowerSO-10 D2PAK

Rthj-case
Rthj-amb
Thermal Resistance Junction-case Max
Thermal Resistance Junction-ambient Max
62.5 C/W C/W
ELECTRICAL CHARACTERISTICS
(-40OFF
Symbol Parameter Test Conditions Min. Typ. Max. Unit

VCLAMP Drain-source Clamp
Voltage= 200 mA Vin=0 34 42 51 V
VCLTH Drain-source Clamp
Threshold Voltage =2 mA Vin =0 31 V
VINCL Input-Source Reverse
Clamp Voltage
Iin=-1 mA -1.1 -0.1 V
IDSS Zero Input Voltage
Drain Current (Vin =0)
VDS =13V Vin =0
VDS =25V Vin =0
IISS Supply Current from
Input Pin
VDS =0V Vin=10V 250 600 μA(∗)
Symbol Parameter Test Conditions Min. Typ. Max. Unit

VIN(th) Input Threshold
Voltage
VDS =Vin ID +Iin =1 mA 0.8 3 V
RDS(on) Static Drain-source On
Resistance
Vin =10V ID =14A
Vin =5V ID =14A
-40Vin =10V ID =14A
Vin =5V ID =14A= 125oC
VNP28N04FI-VNB28N04-VNV28N04
2/13
ELECTRICAL CHARACTERISTICS (continued)
DYNAMIC
Symbol Parameter Test Conditions Min. Typ. Max. Unit

gfs (∗)Forward
Transconductance
VDS =13V ID =14A 9 18 S
Coss Output Capacitance VDS= 13Vf= 1MHz Vin=0 700 1100 pF
SWITCHING (**)
Symbol Parameter Test Conditions Min. Typ. Max. Unit

td(on)
td(off)
Turn-on Delay Time
Rise Time
Turn-off Delay Time
Fall Time
VDD =15V Id =14A
Vgen =10V Rgen =10Ω
(see figure3)
td(on)
td(off)
Turn-on Delay Time
Rise Time
Turn-off Delay Time
Fall Time
VDD =15V Id =14A
Vgen =10V Rgen= 1000Ω
(see figure3)
(di/dt)on Turn-on Current Slope VDD =15V ID =14A
Vin =10V Rgen =10Ω A/μs Total Input Charge VDD =12V ID =10A Vin=10V 60 nC
SOURCE DRAIN DIODE
Symbol Parameter Test Conditions Min. Typ. Max. Unit

VSD (∗)Forward On Voltage ISD =14A Vin =0 2 V
trr (∗∗)
Qrr (∗∗)
IRRM (∗∗)
Reverse Recovery
Time
Reverse Recovery
Charge
Reverse Recovery
Current
ISD=14A di/dt= 100 A/μs
VDD =30V Tj =25oC
(see test circuit, figure5)
PROTECTION
Symbol Parameter Test Conditions Min. Typ. Max. Unit

Ilim Drain Current Limit Vin =10V VDS =13V
Vin =5V VDS =13V
tdlim (∗∗) Step Response
Current Limit
Vin =10V
Vin =5V
Tjsh (∗∗) Overtemperature
Shutdown
150 oC
Tjrs (∗∗) Overtemperature Reset 135 oC
Igf (∗∗) Fault Sink Current Vin =10V VDS =13V
Vin =5V VDS =13V
Eas (∗∗) Single Pulse
Avalanche Energy
startingTj =25o CVDD =20V
Vin =10V Rgen =1 KΩ L=10 mH
2.5 J
(∗) Pulsed: Pulse duration=300μs, duty cycle1.5%
(∗∗) Parameters guaranteedby design/characterization
VNP28N04FI-VNB28N04-VNV28N04

3/13
During normal operation, the Input pin is
electrically connectedto the gateof the internal
power MOSFET. The device then behaves likea
standard power MOSFET and can be usedasa
switch from DCto 50 KHz. The only difference
from the user’s standpointis thata small DC
current (Iiss) flows into the Input pinin orderto
supply the internal circuitry.
The device integrates: OVERVOLTAGE CLAMP PROTECTION:
internally setat 42V, along with the rugged
avalanche characteristics of the Power
MOSFET stage give this device unrivalled
ruggedness and energy handling capability.
This featureis mainly important when driving
inductive loads. LINEAR CURRENT LIMITER CIRCUIT: limits
the drain currentIdto Ilim whatever the Input
pin voltage. When the current limiteris active,
the device operatesin the linear region, so
power dissipation may exceed the capabilityof
the heatsink. Both case and junction
temperatures increase, andif this phase lasts
long enough, junction temperature may reach
the overtemperature threshold Tjsh. OVERTEMPERATURE AND SHORT CIRCUIT
PROTECTION: these are based on sensing
the chip temperature and are not dependenton
the input voltage. The locationof the sensing
element on the chipin the power stage area
ensures fast, accurate detectionof the junction
temperature. Overtemperature cutout occursat
minimum 150oC. The deviceis automatically
restarted when the chip temperature falls
below 135oC. STATUS FEEDBACK: In the case of an
overtemperature fault condition, a Status
Feedbackis provided through the Input pin.
The internal protection circuit disconnects the
input from the gate and connectsit insteadto
ground via an equivalent resistanceof 100Ω.
The failure can be detectedby monitoring the
voltageat the Input pin, which will be closeto
ground potential.
Additional features of this device are ESD
protection accordingto the Human Body model
and the abilityto be driven froma TTL Logic
circuit (witha small increasein RDS(on)).
PROTECTION FEATURES
VNP28N04FI-VNB28N04-VNV28N04

4/13
Thermal Impedance For ISOWATT220
Derating Curve
Transconductance
Thermal Impedance For D2PAK/ PowerSO-10
Output Characteristics
Static Drain-Source On Resistancevs Input
Voltage
VNP28N04FI-VNB28N04-VNV28N04

5/13
Static Drain-Source On Resistance
Input Chargevs Input Voltage
Normalized Input Threshold Voltage vs
Temperature
Static Drain-Source On Resistance
Capacitance Variations
Normalized On Resistancevs Temperature
VNP28N04FI-VNB28N04-VNV28N04

6/13
Normalized On Resistancevs Temperature
Turn-on Current Slope
Turn-off Drain-Source Voltage Slope
Turn-on Current Slope
Turn-off Drain-Source Voltage Slope
Switching Time Resistive Load
VNP28N04FI-VNB28N04-VNV28N04

7/13
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED