IC Phoenix
 
Home ›  VV3 > VN02NSP,HIGH SIDE SMART POWER SOLID STATE RELAY
VN02NSP Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
VN02NSPSTMicroelectronicsN/a2220avaiHIGH SIDE SMART POWER SOLID STATE RELAY


VN02NSP ,HIGH SIDE SMART POWER SOLID STATE RELAYVN02NSPVN02NPTHIGH SIDE SMART POWER SOLID STATE RELAY PRELIMINARY DATATYPE V R )I VDSS DS(on O ..
VN02NSP13TR ,HIGH SIDE SMART POWER SOLID STATE RELAYABSOLUTE MAXIMUM RATINGSymbol Parameter Value UnitV Drain-Source Breakdown Voltage 60 V(BR)DSSI Out ..
VN03 ,ISO HIGH SIDE SMART POWER SOLID STATE RELAYABSOLUTE MAXIMUM RATINGSymbol Parameter Value UnitV Drain-Source Breakdown Voltage 60 V(BR)DSSoI Ou ..
VN0300L ,N-Channel Enhancement-Mode Vertical DMOS FETs
VN0300L ,N-Channel Enhancement-Mode Vertical DMOS FETs
VN0300L ,N-Channel Enhancement-Mode Vertical DMOS FETs
WCMA1008C1X-TF70 , 128K x 8 Static RAM
WCMA1008U1X-SF55 , 128K x 8 Static RAM
WCMA2016U4B-FF70 , 128K x 16 Static RAM
WE2408 , 2.4GHz Single Chip FM Transceiver
WE9140A , TONE/PULSE SWITCHABLE DIALER WITH REDIAL
WE9140A , TONE/PULSE SWITCHABLE DIALER WITH REDIAL


VN02NSP
HIGH SIDE SMART POWER SOLID STATE RELAY
VN02NSP
VN02NPT

HIGH SIDE SMART POWER SOLID STATE RELAY
PRELIMINARY DATA

September 1997
BLOCK DIAGRAM
OUTPUT CURRENT (CONTINUOUS):
6A @ Tc=25oC 5V LOGIC LEVEL COMPATIBLE INPUT THERMAL SHUT-DOWN UNDER VOLTAGE SHUT-DOWN OPEN DRAIN DIAGNOSTIC OUTPUT VERY LOW STAND-BY POWER
DISSIPATION
DESCRIPTION

The VN02NSP/VN02NPT are monolithic devices
made using SGS-THOMSON Vertical Intelligent
Power Technology, intended for driving resistive
or inductive loads with one side grounded.
Built-in thermal shut-down protects the chip from
over temperature and short circuit.
The input control is 5V logic level compatible.
The open drain diagnostic output indicates open
circuit (no load) and over temperature status.
1/10
ABSOLUTE MAXIMUM RATING
CONNECTION DIAGRAMS
CURRENT AND VOLTAGE CONVENTIONS
VN02NSP/VN02NPT

2/10
THERMAL DATA
($) When mounted using minimum recommended pad size on FR-4 board
ELECTRICAL CHARACTERISTICS (VCC = 13 V; -40 ≤ Tj ≤ 125
o C unless otherwise specified)
POWER
SWITCHING
LOGIC INPUT
VN02NSP/VN02NPT

3/10
ELECTRICAL CHARACTERISTICS (continued)
PROTECTION AND DIAGNOSTICS
(*) The VIH is internally clamped at 6V about. It is possible to connect this pin to an higher voltage via an external resistor calculated to not
exceed 10 mA at the input pin. @NOTE = () Status determination > 100 μs after the switching edge.
FUNCTIONAL DESCRIPTION

The device has a diagnostic output which
indicates open circuit (no load) and over
temperature conditions. The output signals are
processed by internal logic.
To protect the device against short circuit and
over-current condition, the thermal protection
turns the integrated Power MOS off at a minimum
junction temperature of 140 o C. When the
temperature returns to about 125 o C the switch is
automatically turned on again.
In short circuit conditions the protection reacts
with virtually no delay, the sensor being located in
the region of the die where the heat is generated.
PROTECTING THE DEVICE AGAINST
REVERSE BATTERY

The simplest way to protect the device against a
continuous reverse battery voltage (-26V) is to
insert a Schottky diode between pin 1 (GND) and
ground, as shown in the typical application circuit
(fig. 3).
The consequences of the voltage drop across
this diode are as follows: If the input is pulled to power GND, a negative
voltage of -VF is seen by the device. (VIL, VIH
thresholds and VSTAT are increased by VF with
respect to power GND).
The undervoltage shutdown level is increased by
VF.
If there is no need for the control unit to handle
external analog signals referred to the power
GND, the best approach is to connect the
reference potential of the control unit to node [1]
(see application circuit infig. 4), which becomes
the common signal GND for the whole control
board.
In this way no shift of VIH, VIL and VSTAT takes
place and no negative voltage appears on the
INPUT pin; this solution allows the use of a
standard diode, with a breakdown voltage able to
handle any ISO normalized negative pulses that
occours in the automotive environment.
VN02NSP/VN02NPT

4/10


ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED