IC Phoenix
 
Home ›  UU13 > UCC3918DP-UCC3918DPTR-UCC3918DPTRG4,0-4A, 3-6V Low RDSON Single Hot-Swap IC Hi-Side MOSFET, Comm. Temp.
UCC3918DP-UCC3918DPTR-UCC3918DPTRG4 Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
UCC3918DPUNITRODEN/a3752avai0-4A, 3-6V Low RDSON Single Hot-Swap IC Hi-Side MOSFET, Comm. Temp.
UCC3918DPTRTIN/a2400avai0-4A, 3-6V Low RDSON Single Hot-Swap IC Hi-Side MOSFET, Comm. Temp.
UCC3918DPTRG4TI/BBN/a128avai0-4A, 3-6V Low RDSON Single Hot-Swap IC Hi-Side MOSFET, Comm. Temp. 16-SOIC 0 to 70


UCC3918DP ,0-4A, 3-6V Low RDSON Single Hot-Swap IC Hi-Side MOSFET, Comm. Temp.maximum ratings” may cause permanent damage to the device. These are stress ratings only, andfuncti ..
UCC3918DPTR ,0-4A, 3-6V Low RDSON Single Hot-Swap IC Hi-Side MOSFET, Comm. Temp.          SLUS384B – NOVEMBER 1999 – REVISED JUNE 2000DP PACKAG ..
UCC3918DPTRG4 ,0-4A, 3-6V Low RDSON Single Hot-Swap IC Hi-Side MOSFET, Comm. Temp. 16-SOIC 0 to 70maximum ratings over operating free-air temperature (unless otherwise noted)Input Voltage . . . . . ..
UCC3918N , LOW ON-RESISTANCE HOT SWAP POWER MANAGER
UCC3918N , LOW ON-RESISTANCE HOT SWAP POWER MANAGER
UCC3921 ,Latchable Negative Floating Single, Hot-Swap IC Commercial Temp.
UPB321611T-121Y-N , SMD Chip Beads
UPB412 , 2048 BIT BIPOLAR TTL
UPB424C , 4096 BIT BIPOLAR TTL
UPB425C , 4096 BIT BIPOLAR TTL
UPB426C , 4096 BIT BIPOLAR TTL
UPB426D , 4096 BIT BIPOLAR TTL


UCC3918DP-UCC3918DPTR-UCC3918DPTRG4
0-4A, 3-6V Low RDSON Single Hot-Swap IC Hi-Side MOSFET, Comm. Temp.
Independent Analog Control of CurrentLimit Up to 5 A Fast Overload Protection Unidirectional Switch Minimal External Components 1-μA ICC When Disabled Programmable On Time Programmable Start Delay Fixed 3% Duty Cycle

description

The UCC3918 low on-resistance hot swap power manager provides complete power management, hot swap
capability, and circuit breaker functions. The only components needed to operate the device, other than supply
bypassing, are a timing capacitor, and two programming resistors. All control and housekeeping functions are
integrated, and externally programmable. These include the fault current level, maximum output sourcing
current, maximum fault time, and startup delay. In the event of a constant fault, the internal fixed 3% duty cycle
ratio limits the average output power. The IFAULT pin allows linear programming of the fault level current from
0 A to 4 A.
Fast overload protection is accomplished by an additional overload comparator. Its threshold is internally set
above the maximum sourcing current limit setting. In the event of a short circuit or extreme current condition,
this comparator is tripped, shutting down the output. This function is needed since the maximum sourcing
current limit loop has a finite bandwidth.
When the output current is below the fault level, the output MOSFET is switched on with a nominal resistance
of 0.075 Ω. When the output current exceeds the fault level or the maximum sourcing level, the output remains
on, but the fault timer starts charging a capacitor connected to the CT pin (CT). Once CT charges to a preset
threshold, the switch is turned off, and remains off for 30 times the programmed fault time. When the output
current reaches the maximum sourcing level, the MOSFET transitions from a switch to a constant current
source.
The UCC3918 is designed for unidirectional current flow, emulating an ideal diode in series with the power
switch. This feature is particularly attractive in applications where many devices are powering a common bus,
such as with SCSI termintation power (Termpwr). The UCC3918 can also be put into the sleep mode, drawing
only 1 μA of supply current.
Other features include an open-drain fault output indicator, thermal shutdown, undervoltage lockout, 3 V to 6 V
operation, and a low thermal resistance small-outline power package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Pin 5 serves as the lowest impedance to the electrical
ground. Pins 4, 12, and 13, serve as heat sink/ground.
These pins should be connected to large etch PCB areas
to help dissipate heat.
GND*
GND*
FAULT
SHTDWN
IFAULT
GND*
GND*
IMAX
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED