TPA2001D1PWR ,Mono Filter-Free Class-D Audio Amplifierfeatures make the device ideal for use in devices where high-efficiency is needed to extendbattery ..
TPA2001D1PWRG4 ,Mono Filter-Free Class-D Audio Amplifierblock diagramV AGNDDDVDDPVDD+Deglitch GateGainOUTN_INN _Logic DriveAdjust+_PGND+_+ PVDD+_Gain _Degl ..
TPA2001D2PWP ,Stereo Filter-Free Class-D Audio AmplifierTPA2001D21-W FILTERLESS STEREO CLASS-D AUDIO POWER AMPLIFIERSLOS292A – MARCH 2000 – REVISED APRIL 2 ..
TPA2001D2PWPRG4 , 1-W FILTERLESS STEREO CLASS-D AUDIO POWER AMPLIFIER
TPA2005D1DGN ,Mono, Fully Differential, Filter-Free Class-D Audio AmplifierMaximum Ratings(1)over operating free-air temperature range (unless otherwise noted)MIN MAX UNITIn ..
TPA2005D1DGNG4 ,1.4-W Mono Class-D Audio Amplifier (TPA2005) 8-MSOP-PowerPAD -40 to 85Features 3 DescriptionThe TPA2005D1 is a 1.4-W high efficiency filter-free1• 1.4 W Into 8Ω From a 5 ..
TR250-120U , PolySwitch™ Resettable Device Short Form Catalog
TR250-120U , PolySwitch™ Resettable Device Short Form Catalog
TR5100 , FM Transceiver IC
TR9-B-S , Transformers for Inverter or Converter
TRC101 , highly integrated single chip
TRC102 , 400-1000MHz RF Transceiver
TPA2001D1-TPA2001D1PW-TPA2001D1PWG4-TPA2001D1PWR-TPA2001D1PWRG4
1-W Filterless Mono Class-D Audio Power Amplifier
<0.2% THD+N at 1 W, 1 kHz, Into an
8-Ω Load Extremely Efficient Third Generation 5-V
Class-D Technology:
– Low-Supply Current (No Filter) ...4 mA
– Low-Supply Current (Filter)... 7.5 mA
– Low-Shutdown Current... 0.05 μA
– Low-Noise Floor ...40 μVRMS
(No-Weighting Filter)
– Maximum Efficiency Into 8 Ω, 75 – 85%
– 4 Internal Gain Settings ...6 – 23.5 dB
– PSRR... –77 dB Integrated Depop Circuitry Short-Circuit Protection (Short to Battery,
Ground, and Load)
descriptionThe TPA2001D1 is a 1-W mono bridge-tied-load (BTL) class-D amplifier designed to drive a speaker with at
least 8-Ω impedance. The amplifier uses TI’s third generation modulation technique, which results in improved
efficiency and SNR. It also allows the device to be connected directly to the speaker without the use of the LC
output filter commonly associated with class-D amplifiers (this results in EMI which must be shielded at the
system level). These features make the device ideal for use in devices where high-efficiency is needed to extend
battery run time.
The gain of the amplifier is controlled by two input terminals, GAIN1, and GAIN0. This allows the amplifier to
be configured for a gain of 6, 12, 18, and 23.5 dB. The differential input terminals are high-impedance CMOS
inputs, and can be used as summing nodes.
The class-D BTL amplifier includes depop circuitry to reduce the amount of turnon pop at power up, and when
cycling SHUTDOWN.
The TPA2001D1 is available in the 16-pin TSSOP package that drives 1 W of continuous output power into an
8-Ω load. TPA2001D1 operates over an ambient temperature range of –40°C to 85°C.
AVAILABLE OPTIONS The PW package is available taped and reeled. To order a taped and reeled
part, add the suffix R to the part number (e.g., TPA2001D1PWR).
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
