TLC5911PZP ,LED Driver W/Shift Registers, Data Latch, On-Chip PLL For Gray Scale Generation & Constant Currentblock diagramXOEBCENADCLK DOUT(9−0)DCLKDPOLXENABLE ControlXDPOUTDIN(9−0), 1 x 10 bit B.C.16 x 10 bi ..
TLC5916IPW ,8-Bit Constant-Current LED Sink Driver 16-TSSOP -40 to 125Block Diagram... 143 Description....... 19.3 Feature Description.... 144 Revision History........ 2 ..
TLC5916IPW ,8-Bit Constant-Current LED Sink Driver 16-TSSOP -40 to 125Maximum Ratings(1)over operating free-air temperature range (unless otherwise noted)MIN MAX UNITV S ..
TLC5916IPW ,8-Bit Constant-Current LED Sink Driver 16-TSSOP -40 to 125Features 3 DescriptionThe TLC591x Constant-Current LED Sink Drivers are1• Eight Constant-Current Ou ..
TLC5916IPWG4 ,8-Bit Constant-Current LED Sink Driver 16-TSSOP -40 to 125Features....... 1• Added Abstract section.. 1• Changed resistor value in Single Implementation diag ..
TLC5916IPWR ,8-Bit Constant-Current LED Sink Driver 16-TSSOP -40 to 125 SLVS695D–JUNE 2007–REVISED JANUARY 20155 Device Comparison TableOVERTEMPERATURE OPEN-LOAD SHORT TO ..
TMP47C670N , CMOS 4-BIT MICROCONTROLLER
TMP47C858F , CMOS 4-BIT MICROCONTROLLER
TMP47C860N , CMOS 4-BIT MICROCONTROLLER
TMP47C860N , CMOS 4-BIT MICROCONTROLLER
TMP47C870N , CMOS 4-BIT MICROCONTROLLER
TMP47C870N , CMOS 4-BIT MICROCONTROLLER
TLC5911PZP
LED Driver W/Shift Registers, Data Latch, On-Chip PLL For Gray Scale Generation & Constant Current
and Internal Brightness Control Register) Constant Current Accuracy
− ±4 % (Maximum Error Between Bits) Voltage Applied to Constant Current Output
Terminals
− Minimum 0.4 V (Output Current 5 mA to
40 mA)
− Minimum 0.7 V (Output Current 40 mA to
80 mA) 1024 Gray Scale Display
− Pulse Width Control 1024 Steps Brightness Adjustment†
− All Output Current Adjustment for 64
Steps (Adjustment for Brightness
Deviation Between LED Modules)
− Output Current Adjustment by Output
(OUT0 to OUT15) for 128 Steps
(Adjustment for Brightness Deviation
Between Dots)
− Brightness Control by 16 Steps
Frequency Division Gray Scale Control
Clock (Brightness Adjustment for Panel) Gray Scale Clock Generation
− Gray Scale Control Clock Generation by
Internal PLL or External Input Selectable Clock Invert/Noninvert Selectable at
Cascade Operation
− Clock Invert Selectable to Reduce
Changes in Duty Ratio
Exceeds Limit) LOD
− LED Open Detection (Detection for LED
Disconnection) Data Input/Output‡
− Port A (for Data Display)
− Clock Synchronized 10 Bit Parallel Input
(Schmitt-Triggered Input)
− Clock Synchronized 10 Bit Parallel
Output (3-State Output)
− Port B (for Dot Correction Data)
− Clock Synchronized 7 Bit Parallel Input
(Schmitt-Triggered Input)
− Clock Synchronized 7 Bit Parallel Output Input/Output Signal Level
− CMOS Level Power Supply Voltage
− 4.5 V to 5.5 V (Logic, Analog and
Constant Current)
− 3 V to 5.5 V (Interface) Maximum Output Voltage ...15 V Data Transfer Rate... 20 MHz (Max) Gray Scale Clock Frequency
− 16 MHz (Max) Using Internal PLL
− 8 MHz (Max) Using External Clock Operating Free-Temperature Range
−20°C to 85°C 100-Pin Package HTQFP (PD = 4.7 W, A = 25°C) † Adjustable for these functions independently.
‡ Allows to write all the data at port A by setting.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
